Instructions

- 10 - - 11 -
GB
This tool may be used by children
aged 8 or above and by persons with
reduced physical, sensory or mental
capabilities or lack of experience and
knowledge if they are supervised or
have been given instructions on how
to use the tool safely and understand
the hazards involved.
Do not allow children to play with the
tool.
Children are not allowed to clean or
carry out maintenance work on the
tool without supervision.
Do not overload your tools.
Your work results and safety will be
enhanced if you operate the tool
within the specified output range. Do
not carry the tool by the power cord.
Do not unplug the tool by pulling on
the power cord. Protect the power
cord from heat, oil and sharp edges.
Beware of toxic gases and
fire hazards.
Toxic gases may develop when
working on plastics, paints, varnishes
or similar materials.
Beware of fire and ignition hazards.
For your own safety, only use acces-
sories and attachments that are
specified in the operating instructions
or recommended or specified by the
tool manufacturer.
Using attachments or accessories
other than those recommended in
the operating instructions or cata-
logue may result in personal injury.
Repairs by a qualified
electrician only
This electric power tool com-
plies with the relevant safety regula-
tions. Repairs should only be per-
formed by a qualified electrician. Oth-
erwise the user may run the risk of
accidents.
If this tool's main power cord is dam-
aged, it must be replaced by the
manufacturer or its customer service
department or a similarly qualified
person so as to avoid hazards.
Keep these safety precautions
with the tool.
Safety precautions
1
2
3
4
8
9
Tool features
6
5
7
10
11
12
13
14
Enclosure
Hanger
Stroke adjustment
Glue stick guide
ON/OFF button
SET button (GluePRO400 LCD only)
UP button for increasing temperature
(GluePRO400 LCD only)
DOWN button for reducing temperature
(GluePRO400 LCD only)
LCD information display
(GluePRO400 LCD only)
Power cord
Stand (removable)
Feed trigger
Exchangeable gluing nozzle
Nozzle cap
Important advice
L Do not use liquid or pasty adhesives.
L Nozzle and molten glue can reach temperatures of
over 200 degrees Celsius. Beware of burns!
L You could burn yourself! After skin contact with
hot glue: immediately cool with cold water. Do not
try to remove hot-melt glue from the skin. If neces-
sary, seek medical attention.
L After eye contact with hot-melt glue: immediately
cool for approx. 15 minutes with running water
and consult a doctor straight away.
L The area you are gluing must be free of grease,
dry and absolutely clean.
L Trouble-free operation can only be guaranteed
when using genuine STEINEL glue sticks.
L Do not use in conjunction with highly flammable/
combustible materials.
L Glue marks on clothing cannot be removed.
L Make sure heat-sensitive materials are suitable for
gluing with hot-melt adhesive.
L Drips of glue are best removed when cold.
L Do not pull glue sticks out of the applicator. Hot
glue running into the applicator may cause dam-
age.
L Optimum adhesion is achieved when the bond is
established instantly on applying the glue.
L Unplug when not in use or during prolonged work
breaks (more than 30 min.).
L Before inserting a new glue stick, wait a moment for
the cold cartridge to heat up. Never force the glue
stick through the applicator.
L Always screw the nozzle hand-tight after replacing
it.
L Once heated up, the applicator must be stood on
the stand.
It must not be laid on its side.
L Unplug after use. Let the tool cool down com-
pletely before putting it away.
L On leaving the factory, the tool is automatically set
to stay switched OFF when the power supply is
restored after a power cut.
Hot-melt glue applicator for use with genuine
STEINEL glue sticks. The tool must only be used
indoors in a dry and well-ventilated environment.
Proper use