assembly Instructions

- 9 -- 8 -
Störung Ursache Abhilfe
Sensorleuchte ohne Spannung
■ Sicherung hat ausgelöst,
nicht eingeschaltet,
Leitung unterbrochen
■ Kurzschluss in der Netzzuleitung
■ evtl. vorhandener Netzschalter aus
■ Sicherung einschalten, tauschen,
Netz schalter einschalten, Lei tung
überprüfen mit Spannungsprüfer
■ Anschlüsse überprüfen
■ Netzschalter einschalten
Sensorleuchte schaltet nicht ein
■ Dämmerungseinstellung falsch
gewählt
■ Netzschalter AUS
■ Sicherung hat ausgelöst
■ neu einstellen
■ einschalten
■ Sicherung einschalten, tauschen
evtl. Anschluss überprüfen
Sensorleuchte schaltet nicht aus
■ dauernde Bewegung im
Erfassungsbereich
■ Bereich kontrollieren
Sensorleuchte schaltet ohne
erkennbare Bewegung ein
■ Leuchte nicht bewegungssicher
montiert
■ Bewegung lag vor, wurde jedoch
vom Beobachter nicht erkannt
( Bewegung hinter Wand, Bewegung
eines kleinen Objektes in unmittelbarer
Leuchtennähe etc. )
■ Gehäuse fest montieren
■ Bereich kontrollieren
Sensorleuchte schaltet trotz
Bewegung nicht ein
■ schnelle Bewegungen werden zur
Störungsmini mierung unterdrückt oder
Erfassungsbereich zu klein
eingestellt
■ Dämmerungseinstellung falsch gewählt
■ Bereich kontrollieren
■ neu einstellen
11. Betriebsstörungen
A Shade
B Electronics enclosure
C HF sensor
D Connecting terminal
E Night light
F Time setting
G Reach adjustment
H Twilight setting
Detection zones for ceiling mounting
Ø 3-8 m ( Fig.3.4 )
Detection zones for wall mounting
Ø 2.50 m ( Fig.3.5 )
4. Electrical installation
Wiring diagram ( Fig.4.1 )
The mains power supply lead is a 3-core cable:
L = phase conductor ( usually black, brown or grey )
N = neutral conductor ( usually blue )
PE = protective-earth conductor ( green/yellow )
If you are in any doubt, identify the conductors using a volt-
age tester; then disconnect from the power supply again.
Connect the phase conductor ( L ) and neutral conductor
( N ) to the terminal block.
Important:
Incorrectly wired connections will produce a short circuit lat-
er on in the product or your fuse box. In this case, you must
identify the individual conductors once again and reconnect
them. A mains power switch for turning the unit ON and
OFF may of course be installed in the mains supply lead.
The light source of this luminaire cannot be replaced. If the
light source needs to be replaced ( e.g. at the end of its
service life ), the complete luminaire must be replaced.
Connection to a dimmer will result in damage to the sen-
sor-switched light.
5. Mounting
• Check all components for damage.
• Do not use the product if it is damaged.
• When installing the sensor-switched light, make sure the
installation site is not exposed to vibration.
• Select an appropriate mounting location, taking the
reach and motion detection into consideration.
Mounting procedure
• Switch OFF power supply ( Fig.4.1 )
• Mark drill holes ( Fig.5.1 )
• Drill holes and insert wall plugs ( Fig.5.2 )
• Installation with concealed power supply lead ( Fig.5.3 )
• Installation with surface-mounted power supply lead
( Fig.5.4 )
• Connect conductors ( Fig.5.5 )
• Make settings ➔ "6.Functions" ( Fig.5.6 )
• Fit shade ( Fig.5.7 )
• Switch ON power supply ( Fig.5.7 )
GB
1. About this document
Please read carefully and keep in a safe place.
– Under copyright. Reproduction either in whole or in part
only with our consent.
– Subject to change in the interest of technical progress.
Symbols
!
Hazard warning!
...
Reference to other information in the
document.
2. General safety precautions
Disconnect the power supply before attempt-
ing any work on the unit.
• During installation, the electric power cable being con-
nected must not be live. Therefore, switch o the power
first and use a voltage tester to make sure the wiring is
o-circuit.
• Installing the sensor-switched light involves work on the
mains supply voltage. This work must therefore be car-
ried out professionally in accordance with national wiring
regulations and electrical operating conditions.
( e.g. DE- VDE 0100, AT- ÖVE / ÖNORM E8001-1,
CH- SEV 1000 )
• Only use genuine replacement parts.
• Repairs may only be made by specialist workshops.
3. RS LED D1/D2
Proper use
- Sensor-switched indoor light with active motion detector
for installing indoors
The integrated HF sensor emits high-frequency electromag-
netic waves ( 5.8 GHz ) and receives their echo. The change
in echo caused by the slightest movement within the light's
detection zone is detected by the sensor. A microprocessor
then issues the switch command "switch light ON". Detec-
tion is possible through doors, panes of glass or thin walls.
Note:
The high-frequency power of the HF sensor is approximate-
ly 1mW – 1000 times less than the transmission power of a
mobile phone or microwave oven.
Package contents ( Fig.3.1 )
Product dimensions ( Fig.3.2 )
Product components ( Fig.3.3 )
!
GB