assembly Instructions

- 11 -- 10 -
6. Function
The sensor-switched light can be put into service after
mounting the enclosure and connecting to the mains power
supply. When putting the light into operation manually at the
light switch, the light will switch OFF after 10 seconds for the
calibration phase and is then activated for sensor mode. It is
not necessary to operate the light switch a second time.
Function - control dials ( Fig.6.1 )
Factory settings:
Time setting: 5 seconds
Reach setting: 8m
Twilight level: 2000lux
Basic brightness: 10%
Time setting ( stay-ON time ) ( Fig.6.1/F )
The light's ON time can be set to any period from approx.
5 seconds to a maximum of 15 minutes. Any movement
detected before this time elapses will restart the timer.
Note:
After the light switches OFF, it takes approx. 1 second
before it is able to start detecting movement again. The
light will only switch ON in response to movement once this
period has elapsed.
The shortest time setting is recommended when adjusting
the detection zone and performing the functional test.
Reach setting ( sensitivity ) ( Fig. 6.1/G )
Reach is the term used to describe the diameter of the
more or less circular detection zone produced on the floor
after mounting the sensor-switched light at a height of
2.50m.
– Control dial set to maximum = max. reach ( 8 m )
– Control dial set to minimum = min. reach ( 2.50 m )
Twilight setting / response threshold ( Fig.6.1/H )
The light's chosen response threshold can be infinitely
varied from approximately 2 to 2000 lux.
– Control dial set to
= daylight mode ( depending on
ambient brightness )
– Control dial set to = twilight mode ( approx. 2 lux )
The control dial must be turned to
when adjusting the
detection zone and performing the functional test in daylight.
Night light ( Fig.6.1/E )
The night light provides illumination at approx. 10% of full
light output. The light only switches to maximum output
( 100% ) in response to movement in the detection zone
( see Time setting ). The light then switches to the activated
night light level.
– Control dial set to
= night light activated
– Control dial set to 0 = night light deactivated
Night light is ON when the level of light falls below the
brightness threshold. Night light is always ON when daylight
mode is activated.
Manual override function
If a mains switch is installed in the mains supply lead,
the following functions are available in addition to simply
switching light ON and OFF:
Manual override ( Fig. 6.2 )
1 ) Activate manual override:
Switch OFF and ON twice. Light is set to
manual override for 4 hours. Then it returns automatically to
sensor mode.
2 ) Deactivate manual override:
Switch OFF and ON once. Light goes out or switches to
sensor mode.
Important:
The switch should be actuated in rapid succession ( in the
0.2 to 1second range ).
7. Disposal
Electrical and electronic equipment, accessories and pack-
aging must be recycled in an environmentally compatible
manner.
Do not dispose of electrical and electronic
equipment as domestic waste.
EU countries only
Under the current European Directive on Waste Electrical
and Electronic Equipment and its implementation in national
law, electrical and electronic equipment no longer suitable
for use must be collected separately and recycled in an
environmentally compatible manner.
8. Declaration of Conformity
STEINEL Vertrieb GmbH hereby declares that the
RS LED D1 / RS LED D2 radio equipment type conforms
to Directive 2014/53/EU. The full wording of the EU Decla-
ration of Conformity is available for downloading from the
following Internet address: www.steinel.de
9. Manufacturer's warranty
This Steinel product has been manufactured with utmost
care, tested for proper operation and safety and then sub-
jected to random sample inspection. Steinel guarantees that
it is in perfect condition and proper working order.
The warranty period is 36 months and starts on the date of
sale to the consumer. We will remedy defects caused by
material flaws or manufacturing faults. The warranty will be
met by repair or replacement of defective parts at our own
discretion. The warranty shall not cover damage to wear
parts, damage or defects caused by improper treatment or
maintenance. Further consequential damage to other ob-
jects shall be excluded.
Claims under the warranty will only be accepted if the unit is
sent fully assembled and well-packed with a brief descrip-
tion of the fault, a receipt or invoice ( date of purchase and
dealer’s stamp ) to the appropriate Service Centre.
Repair service:
If defects occur outside the warranty pe-
riod or are not covered by warranty, ask
your nearest service station for the possi-
bility of repair.
10. Technical specifications
Dimensions ( H × W × D ) 300 × 300 × 65.5 mm
Material Plastic
Power supply 220 - 240 V, 50 / 60 Hz
Power consumption 9.5 W / 795 lm / 84 lm/W
Standby 0.4 W
Power factor 0.93
Colour temperature 3000 Kelvin ( warm white )
LED life expectancy 65,000 hours
HF technology 5.8 GHz ( responds to the slightest movement regardless of temperature )
Angle of coverage 360° with 160° angle of aperture
Transmitter power approx. 1 mW
Detection reach Ø 3 to 8 m
Twilight setting 2 - 2000 lux
Time setting 5 s - 15 min
IP rating IP20
Protection class II
Temperature range -10°C to +40°C
Malfunction Cause Remedy
Sensor-switched light without
power
■ Fuse has tripped, not switched ON,
break in wiring
■ Short circuit in mains power supply lead
■ Any mains switch OFF
■ Activate, change fuse, turn ON mains
switch, check wiring with voltage tester
■ Check connections
■ Switch on mains switch
Sensor-switched light will not
switch ON
■ Incorrect twilight setting selected
■ Mains switch OFF
■ Fuse has tripped
■ Readjust
■ Switch ON
■ Activate, change fuse,
check connection if necessary
Sensor-switched light will not
switch OFF
■ Continued movement within the
detection zone
■ Check detection zone
Sensor-switched light switches
ON without any identifiable
movement
■ Light not mounted for detecting move-
ment reliably
■ Movement occurred, but not identified
by the observer ( movement behind wall,
movement of a small object in immediate
light vicinity etc. )
■ Securely mount enclosure
■ Check detection zone
Sensor-switched light does not
switch ON despite movement
■ Rapid movements are suppressed to
minimise malfunctioning or detection
zone set too small
■ Incorrect twilight setting selected
■ Check detection zone
■ Readjust
11. Troubleshooting
MANUFACTURER'S
1
3
5
YEAR
GB
WARRANTY
MANUFACTURER'S
YEAR
WARRANTY
MANUFACTURER'S
YEAR
WARRANTY
GB