Instructions / Assembly

INSASIRH0117
2
Before installing and operating this product, the user and/or installer must read, understand and follow these instructions and keep them handy for future
reference. If these instructions are not followed, the warranty will be considered null and void and the manufacturer deems no further responsibility for this
product.
This product must be installed by a qualied person and connected by a certied electrician, according to the electrical and building codes effective in your
region.
The following instructions must be adhered to in order to avoid personal injuries or property damages, serious injuries and potentially fatal electric shocks.
Protect the heating unit with the appropriate circuit breaker or fuse, in accordance with the nameplate.
Make sure the line voltage (volt) is consistent with that indicated on the unit’s nameplate.
This unit must be grounded.
Switch off the power at the circuit breaker/fuse before installing, repairing and cleaning the unit.
Make sure the unit is appropriate for the intended use (if needed, refer to the product catalog or a representative). Use this heater only as described in this
manual. Any other use not recommended by the manufacturer may cause re, electric shock, or injury to persons.
Do not install the unit where objects could be heat damaged or where object could burn if they are too close from the front of the heater.
Respect distances and positions indicated in the installation section.
If the installer or the user modies the unit, they will be held responsible for any damage resulting from this modication, and the CSA certication could be
void.
Because this unit is hot when in use, it may pose risks even in normal operation. Therefore, be careful and responsible when using it. To avoid burns, do not
let bare skin touch hot surfaces. Let the unit cool down for a few minutes before handling it (it stays warm for some time after shutdown). Extreme caution is
necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
Make sure objects do not come into contact with the unit and keep them away from it at distances greater than the ones specied in this guide and on the
warning label on the unit (see the Installation section). Failure to comply with this warning could lead to a re. Some materials are more heat-sensitive than
others, so make sure those near the unit can withstand heat.
Do not use this unit in areas where you can nd large amount of inammable dust, vapors or gases in suspension.
Never block air vents (with objects or other items). You risk damaging the heater and the obstruction could lead to electric shock or overheating, which could
result in a re.
Do not insert or allow foreign objects to enter any air vent as this may cause electric shocks, res, or damages to the unit.
Do not use this product in areas containing ammable liquids, combustible materials or corrosive, abrasive, chemical, explosive and ammable substances
such as, but not limited to, gasoline, paint, chlorine and cleaning products.
Some areas are dustier than others. Accumulated dirt can lead to a component malfunction or discoloration (yellowing). It may cause a re hazard if not
installed and maintained in accordance with these instructions.
Before unplugging the unit, all controls must be in the “OFF” position and the current from the main breaker panel should be cut. (The general switch may be
used also, if included.)
If the unit is damaged or defective, discontinue use, cut off power supply at circuit breaker and contact a certied electrician or certied repair centre. (Refer
to the limited warranty)
Ensure to choose the model required for your application. You can ask either your distributor or the customer service. Overheating may occur if the chosen
model is too powerful for the application.
SAVE THESE INSTRUCTIONS
AVERTISSEMENT
Note: This unit is designed to increase comfort, not to heat the ambiant air. A lot of factors can have an impact on the heat felt by users (wind, weather, etc.). It is
important to consider it before using the unit.
When a part of the product specication must be changed to improve operability or other functions, priority is given to the product specication itself. In such
instances, the instruction manual may not entirely match all the functions of the actual product. Therefore, the actual product and packaging, as well as the name
and illustration, may differ from the manual.
SPECIFICATIONS
WATTAGE VOLTAGE FREQUENCY LENGTH HEIGHT DEPTH WEIGHT
CODE WATTS VOLTS Hz IN. MM IN. MM IN. MM LB KG
ASIRH1501W* 1500 120 60 19 483 10 254 5 5/8 143 11.0 5.0
ASIRH2002W* 2000/1600 240/208 60 19 483 10 254 5 5/8 143 11.0 5.0
ASIRH4002W* 4000/3200 240/208 60 19 483 15 7/8 403 5 5/8 143 13.8 6.25
ASIRH4203W* 4180 347 60 19 483 21 13/16 554 5 5/8 143 16.3 7.4
ASIRH6002W* 6000/4800 240/208 60 19 483 21 13/16 554 5 5/8 143 16.3 7.4
* Add R for the weather-resistant model
IMPORTANT INSTRUCTIONS
SPECIFICATIONS