USER’S GUIDE SOA SERIES FAN HEATER TÈME QUAL ITÉ SYS For further information or to consult this guide online, please visit our website at www.stelpro.com.
WARNING IMPORTANT INSTRUCTIONS Before installing and using this product, you must read and understand these instructions and keep them for future reference. If the installer and the user do not follow these instructions, the manufacturer cannot be held liable in any way and the warranty will be null and void. This product must be installed by a qualified person and connected by a certified electrician, according to the electrical and building codes effective in your region. For indoor installation only.
INSTALLATION Cut off power supply at circuit breaker/fuse before proceeding to the installation. Use the appropriate screw sets (minimum head diameter 1/4 in (6.5 mm) and anchors according to the wall type and the weight of the product (10 lbs). When drilling into the wall, make sure not to damage the electrical wiring and other hidden utilities. N.B. This product must be connected by a certified electrician, according to the electrical and building codes effective in your region.
INSTALLING THE WALL MOUNT SUPPORT (CORDED UNIT ONLY) RECOMMENDED HEIGHT: 10 in (254 mm) FROM THE GROUND (certified at minimum 6 in) 1. Remove the wall mount from the unit by pressing the plastic tab at the bottom of the unit. 2. Place the wall mount at the desired height, making sure to respect the minimum clearance from the floor. 3. Secure the mount to the wall. Make sure it is level by using screw sets (minimum head diameter 1/4 in (6.
OPERATION WITH A WALL-MOUNTED THERMOSTAT Choose a thermostat equipped with a TRIAC, which makes it possible to maintain a precise temperature, thus increasing your level of comfort. WITH A BUILT-IN ELECTRONIC THERMOSTAT FOR SMART HOMES DISPLAYED ITEM LISTING 1 2 3 5 1 The 6 4 8 9 7 7 Ambient room temperature (or the temperature setpoint, if the dis- icon if the unit is overheating. play is flashing). In Boost mode, the Boost mode time remaining . 2 Displays the remaining time of the BOOST mode.
BUTTON FUNCTIONS BUTTONS MAIN SCREEN ADVANCED MENUS HIGH BUTTON OR LOW BUTTON Set the temperature setpoint* Browse and edit settings BOOST BUTTON Activate/deactivate BOOST mode Select and confirm BOOST setting (in the BOOST menu) UP AND DOWN BUTTONS SIMULTANEOUSLY FOR 3 SECONDS Access advanced menus Exit advanced menus BOOST BUTTON FOR 3 SECONDS Access BOOST menu Exit BOOST menu UP AND DOWN BUTTONS SIMULTANEOUSLY FOR LESS THAN 3 SECONDS --- Selection in Advanced Menus *If the UP or DOWN bu
ELECTRICAL WIRING The supply wires must be connected in accordance with all codes in effect. Connect the bare wire (ground) to the unit’s ground screw (green). Connect wires from the electrical box to the unit’s supply leads. N.B. This product must be connected by a qualified electrician according to electrical and building codes in effect in your region.
TROUBLESHOOTING PROBLEM The unit does not work The unit runs continuously The housing is extremely hot The desired room temperature cannot be reached Overheating The heater is on and the breaker trips The unit does not heat Thermal protection is activated, which translates to ventilation without heat.
REPLACEMENT COMPONENTS LIST RÉF. # 1 2 3 4 PART # ELF-043 ELF-044 240 V ELEMENT WITH INTEGRATED PROTECTION 120 V ELEMENT WITH INTEGRATED PROTECTION MO-087 240 V MOTOR/FAN MO-089 120V MOTOR/FAN P-SORB00D0 RÉF.
MAINTENANCE N.B. High voltage and the risk of electric shock are present in the unit even if the thermostat is set to off. Therefore, you can receive an electrical shock as long as the unit is under power. Always cut off the power at the breaker or fuse prior to cleaning the unit. Use a soft rag to dust the unit or a damp cloth to clean it. In order to prevent yellowing and/or damage to the product finish, do not use cleaning products (chemical or abrasive).
