Use and Care Manual

7
INSASOR1016
N.B. In order for the warranty on this product to remain valid, it
must be cleaned on a regular basis.
Always cut off the power at the breaker or fuse prior to cleaning the
unit. Use a soft rag to dust the unit or a damp cloth to clean it. In order
to prevent yellowing and/or damage to the product nish, do not use
cleaning products (chemical or abrasive). Regularly use a vacuum
brush to remove dust and any other foreign objects from the grill if the
product is installed in a very dusty area.
NOTE: Cigarette smoke can accelerate the yellowing of the discharge
grill. More frequent cleanings are recommended in these conditions.
N.B. High voltage and the risk of electric shock are present in the
unit even if the thermostat is set to OFF.
STAINLESS STEEL CLEANING TIPS
Although stainless steel is corrosion resistant, its nish can still be
damaged. It is recommended to clean the stainless steel surfaces
on a regular basis and not to wait until a full cleaning is necessary.
Since the acidity level and chlorine content of regular cleaning agents
vary greatly, it is highly recommended to thoroughly rinse the surface
with clean water following their use. Stainless steel polishes can also
be used and are recommended. Always polish the stainless steel
surfaces with the grain and never against the grain.
DO NOT USE
- chlorine or chlorine-based cleaners
- scrubbing pads or other scrubbing devices (steel wool)
- abrasive cleaning agents
- hydrochloric acid-based products such as bleach: they can stain
and/or damage stainless steel surfaces
MAINTENANCE
Do not use cleaning
products identied
with these symbols:
°STELPRO MENU
Information about the convector is available in this menu. It is also
possible to reset the convector to its factory settings (menu 7.7).
Follow these steps to access this information:
- Access the advanced menus
- Select menu 7
- Select one of the following sub-menus:
- 7.1 : Version of convector
- 7.2 : Version of ZigBee ‘radio’
- 7.3 : Day manufactured
- 7.4 : Month manufactured
- 7.5 : Year manufactured
- 7.6 : Internal control code
- 7.7 : Factory reset of convector
FREEZE PROTECTION
The ( ) icon will be displayed when the thermostat is adjusted
between 5 °C (41 °F) and 7 °C (45 °F) and indicates that the ambient
room temperature will not drop below the freezing point.
NO HEAT MODE
See the SELECTING THE OPERATION MODE section for procedure to
activate the NO HEAT mode.
NOTE #1 : There is still voltage present in the convector and there
is a risk of electric shock even if the NO HEAT mode is activated.
Always switch the circuit breaker off prior to servicing or cleaning the
convector.
NOTE #2 : The convector will NEVER heat when in the NO HEAT
mode. A freeze risk is present when the NO HEAT mode is activated.
FACTORY RESET
Follow these steps to reset the convector to its factory settings:
- Access the advanced menus
- Select menu 7
- Select sub-menu 7.7. Conrm selection when (def) is displayed
- Select (yes) and conrm the selection
- (yes) will blink for few seconds and the convector will be reset to its
factory settings
BUTTON CONTOUR COLORS
BUTTON CONTOUR COLORS CONVECTOR CONDITION
GREEN NORMAL OPERATION, ECONOMICAL TEMPERATURE SETPOINT
BETWEEN GREEN AND RED
NORMAL OPERATION, THE COLOR REFLECTS HOW ECONOMICAL THE TEMPERATURE SETPOINT IS; MORE GREEN IS MORE
ECONOMICAL AND MORE RED IS LESS ECONOMICAL.
RED NORMAL OPERATION, HIGH TEMPERATURE SETPOINT
BLUE CONVECTOR IN ‘NO HEAT’ MODE
FLASHING BLUE OPEN WINDOW DETECTED
WHITE WHILE IN ADVANCED MENUS
GRAY WHEN THE BACKLIGHTING IS SET TO ‘NO HEAT’ AND THE BUTTONS REMAIN INACTIVE FOR MORE THAN 15 SECONDS
OPERATION & MAINTENANCE