CONGRATULATIONS! You have purchased a product made in Quebec, Canada
USER’S GUIDE ASOR SERIES HIGH-END CONVECTOR TÈME QUAL ITÉ SYS EG IÉ - R ISTERE D TIF Q ER STEM Y SY LIT UA C REPLACEMENT COMPONENT LIST INCLUDED This unit complies with CSA and UL standards
IMPORTANT INSTRUCTIONS Before installing and operating this product, the user and/or installer must read, understand and follow these instructions and keep them handy for future reference. If these instructions are not followed, the warranty will be considered null and void and the manufacturer deems no further responsibility for this product.
SPECIFICATIONS & TECHNICAL DRAWINGS MODEL WATTS VOLTS MM LENGTH IN. KG LB HIGH MODELS - HEIGHT: 708 mm (27 7/8 in.) ASORH1002 1000/750 240/208 457 18 6.8 15.1 ASORH1502 1500/1125 240/208 623 24 1/2 8.8 19.4 ASORH2002 2000/1500 240/208 768 30 1/4 10.5 23.2 LOW MODELS - HEIGHT: 330 mm (13 in.) ASORL1002 1000/750 240/208 750 29 1/2 5.2 11.5 ASORL1502 1500/1125 240/208 1113 38 7/8 6.9 15.1 ASORL2002 2000/1500 240/208 1276 50 1/4 8.3 18.
INSTALLATION & ELECTRIC WIRING N.B. Cut off power supply at circuit breaker/fuse before proceeding with the installation. To reduce the risk of fire, do not store or use gasoline or other flammable vapors and liquids in the vicinity of the heater. Do not mount in contact with combustible material. Do not mount in close proximity to another unit. CAUTION – High temperature; risk of fire. Keep electrical cords, drapery, furnishings, and other combustibles at least 3 feet (0.
OPERATION BUILT-IN ELECTRONIC THERMOSTAT FOR SMART HOMES (ST218) ADJUSTING THE TEMPERATURE SETPOINT -- By pressing either button on the thermostat, the temperature setpoint will be displayed as flashing digits. -- The temperature setpoint is set by using the UP ( ) or DOWN ( ) buttons to raise or lower the setpoint respectively by increments of 0.5 °C (1 °F) each time the buttons are pressed. Holding down either button will allow you to scroll more quickly to the desired temperature setpoint.
OPERATION BUTTON FUNCTIONS BUTTONS DISPLAY ADVANCED MENUS SINGLE BUTTON ADJUSTMENT OF TEMPERATURE SETPOINT NAVIGATION AND EDITING OF PARAMETERS BOTH BUTTONS SIMULTANEOUSLY MODE SELECTION (COMFORT, ECO, NO HEAT) SELECTION AND CONFIRMATION OF PARAMETERS BOTH BUTTONS HELD SIMULTANEOUSLY FOR 3 SECONDS ACCESS TO ADVANCED MENUS EXIT FROM ADVANCED MENUS ZIGBEE CONNECTIVITY 3 - OFF: The backlighting is off.
OPERATION & MAINTENANCE °STELPRO MENU NO HEAT MODE Follow these steps to access this information: NOTE #1 : There is still voltage present in the convector and there is a risk of electric shock even if the NO HEAT mode is activated. Always switch the circuit breaker off prior to servicing or cleaning the convector. Information about the convector is available in this menu. It is also possible to reset the convector to its factory settings (menu 7.7).
TROUBLESHOOTING PROBLEM DEFECTIVE PART OR PART TO CHECK The unit does not work - Defective thermostat - Open circuit breaker or fuse - Thermal protection activated - Faulty connections The unit runs continuously - Defective wall mounted thermostat - Heat losses greater than the unit capacity The housing is extremely hot - Defective thermal protection - Blocked air vents The desired room temperature cannot be reached - One or more defective elements - Defective wall mounted thermostat - Voltage lowe
REPLACEMENT COMPONENT LIST MODEL HOUSING FRONT PANEL WALL SUPPORT THERMAL PROTECTION (AUTO.
LIMITED WARRANTY This limited warranty is offered by Stelpro Design inc. (“Stelpro”) and applies to the following product made by Stelpro: ASOR model. Please read this limited warranty carefully. Subject to the terms of this warranty, Stelpro warrants its products and their components against defects in workmanship and/or materials for the following periods from the date of purchase: 5 years (3 years on electronic components).