Use and Care Manual

6
INSASOR1016
ZIGBEE CONNECTIVITY
This convector is compatible with the ZigBee smart home protocol.
Once connected, it can be controlled remotely by means of the
application included with the user’s ZigBee controller.
FOLLOW THESE STEPS TO CONNECT YOUR CONVECTOR TO A
ZIGBEE NETWORK:
- Make sure that the ZigBee controller is in ASSOCIATION mode
- Access the advanced menus
- Select menu 1 ( )
- If ON is selected, the convector will nd the channel assigned to the
ZigBee network. You can also manually specify the channel that your
ZigBee controller is currently using. The ZigBee connection process
will be faster if the ZigBee channel is manually specied.
- During the association, your selection will ash rapidly and the
connectivity icon ( ) will be animated
- Once the association with the ZigBee network has been established,
the channel number will be shown on the display
- If an error occurs during association, (ERR) will be displayed for 3
seconds followed by (NO HEAT) being displayed
FOLLOW THESE STEPS TO DISCONNECT YOUR CONVECTOR
FROM THE ZIGBEE NETWORK:
- Access the advanced menus
- Select menu 1 ( )
- Change the parameter to (NO HEAT)
- During the disassociation, (NO HEAT) will ash rapidly and the
connectivity icon ( ) will be animated
- Once the disassociation with the ZigBee network has been
completed, (NO HEAT) will be displayed
- If an error occurs during disassociation, (ERR) will be displayed for
3 seconds followed by the channel number being displayed
TEMPERATURE FORMAT
The temperature can be displayed in either degrees Celsius or
Fahrenheit.
Follow these steps to select the temperature format:
- Access the advanced menus
- Select menu 2
- Select either °C or °F
DISPLAY BACKLIGHTING
Both the display backlighting as well as the lighted control buttons can
be congured. When either button is pressed, the buttons are lit with a
color (see ADJUSTING THE TEMPERATURE SETPOINT for details of
colors displayed) and the display will be at 100% brightness. If no button
is pressed for 15 seconds, the display can behave in one of three ways:
1 - ALL: The display backlighting is active but dimmed. The button
contours remain colored
2 - BTN: The backlighting is off. The button contours remain colored.
3 - OFF: The backlighting is off. The button contours are colored light gray
Follow these steps to congure the backlighting and button behavior:
− Access the advanced menus
− Select menu 3 ( )
− Select ALL, BTN or OFF
NOTE: The display backlighting and the button contours will be at
100% intensity if a problem is detected with the ZigBee communication
or if a window is open.
LOCKING THE CONTROLS
This mode allows you to lock the controls in order to prevent unwanted
changes to the setpoint and/or operation modes.
While the ( ) icon is displayed, only changes sent by the ZigBee
controller are possible.
NOTE: The advanced menus remain accessible at all times.
Follow these steps to activate or deactivate the control lock:
- Access the advanced menus
- Select menu 4 ( )
- Select (ON) or (NO HEAT)
OPEN WINDOW DETECTION
This convector can detect an open window in the room and lower the
setpoint so as not to waste energy.
When the convector detects an open window in the room, the ( ) icon
will ash and the button contours will ash in blue. The setpoint will be
automatically set to 7 °C (45 °F).
Once the convector detects that the window has been closed, the setpoint
will return to its previous setting.
Follow these steps to activate or deactivate the open window detection:
- Access the advanced menus
- Select menu 5 ( )
- Select (ON) or (NO HEAT)
ECO MODE DURATION
By default, the ECO ( ) mode duration is set to (NO HEAT). In
other words, the mode selection is permanent and the convector will
remain in ECO mode unless another mode is manually selected or
selected remotely by the smart home controller.
Follow these steps to modify the duration of the ECO ( ) mode:
- Access the advanced menus
- Select menu 6 ( )
- Select the duration from the values available ranging from:
- 1-12 hrs, in one hour increments
- 14 hrs
- 16 hrs
- 18 hrs
- 1-7 days, in one day increments
BUTTON FUNCTIONS
BUTTONS DISPLAY ADVANCED MENUS
SINGLE BUTTON ADJUSTMENT OF TEMPERATURE SETPOINT NAVIGATION AND EDITING OF PARAMETERS
BOTH BUTTONS SIMULTANEOUSLY MODE SELECTION (COMFORT, ECO, NO HEAT) SELECTION AND CONFIRMATION OF PARAMETERS
BOTH BUTTONS HELD SIMULTANEOUSLY FOR 3 SECONDS ACCESS TO ADVANCED MENUS EXIT FROM ADVANCED MENUS
OPERATION