User Guide

ManualsBrandsStelPro ManualsElectronic ThermostatSTELPRO SIBTE13F Built-In Electronic Thermostat

3 3 4

4 4

BRAVA

PRIMA

PRIMA PRIMA

PRIMA

Saint-Bruno-de-Montarville, Quebec, Canada, J3V 6L7

STELPRO DESIGN INC.

INS-SIBTE_0622

1-844-STELPRO WWW.STELPRO.COM

PREPARE THE BASEBOARD

ASSEMBLE THE

THERMOSTAT

CONNECT THE POWER

SUPPLY WIRES

INSTALL THE TEMPERATURE SENSOR

INSTALL THE INTERFACE

Before installing or using this product, you must read and understand

these instructions. The manufacturer cannot be held responsible for

anything, and the warranty will not be valid if the installer and user do

not follow these instructions. Failure to comply with these instruc-

tions could result in bodily harm, property damage, serious injury and

potentially fatal electric shock.

The thermostat must be installed by a certiﬁed electrician.

WARNING: HIGH VOLTAGE. Turn off the power supply

before installation and maintenance.

SAVE THESE INSTRUCTIONS

WARNING: Turn off the power supply. Do not install the thermostat

in a position other than that indicated in this guide.

1. Choose which side of the baseboard to install the thermostat. The connection must

be made in the same junction box as the power supply.

2. Remove the front panel. Refer to the baseboard instructions for more details.

3. Unscrew the front cover of the junction box [A] and remove it.

4. Remove the knockouts [B] with a hammer and a screwdriver.

1. Attach the thermostat using the screws

provided.

2. To ensure proper grounding and heat transfer,

make sure the thermostat is screwed in

securely and is in contact with the junction

box cover.

Complete the thermostat’s electrical connection

according to one of the diagrams below. Tighten

the wires securely in the supplied connection

caps.

WARNING: Be sure to connect the wire

colours as shown in the diagrams when

making electrical connections.

Install the temperature

sensor [A] as shown,

making sure it is rmly

seated at the bottom

of the groove.

1. Make sure surfaces are clean and dry. Position the interface so that the numbers

facein the correct direction, as shown.

2. Remove the adhesive protection on the back of the interface.

3. Insert the connector into the opening. Clip the interface into place and press rmly

sothat the adhesive sticks to the surface.

4. Clip the interface connector into the thermostat connector.

5. Push all the wires into the junction box while closing it. Be sure that the at exible cable

does not interfere with the wires and that the sensor wires are not pinched by the cover

as this could damage them.

6. Screw the junction box cover back on, then replace the front panel.

7. Restore the power supply.

INITIAL SETTING

Once installation is complete, you must congure your

thermostat according to your baseboard model.

BASEBOARDS

MODEL F

(Fahrenheit)

MODEL C

(Celsius)

INDICATOR

LIGHTS

BRAVA*

Press simultaneously

3 sec.

Press simultaneously

3 sec.

Purple

PRIMA

Press simultaneously

3 sec.

Press simultaneously

3 sec.

Light blue

ADJUSTING THE TEMPERATURE

Here are some examples of how to use the three buttons on

thethermostat to adjust the setpoint temperature.

DESIRED TEMPERATURE PRESS INDICATOR LIGHTS

72 °F* Orange

67 °F* Green

41 °F*

Freeze protection

3 sec. Blue

LOCK/UNLOCK FEATURE

PRESS INDICATOR LIGHTS

LOCK

Press simultaneously

3 sec.

After 3 sec., 3 white ﬂashes

UNLOCK

After 3 sec., display of the

current setpoint color

When an attempt is made to change the setpoint while in lock mode,

the indicator lights will ﬂash white three times.

INDICATOR LIGHTS

The indicator lights provide feedback on your comfort choices

and other advanced features.

COLOUR DESCRIPTION

TEMPERATURE

MODEL F (Fahrenheit)

BLUE

Freeze protection 41°F 5°C

GREEN

Energy saving 42°F to 66°F 6°C to 19°C

GREEN TO ORANGE

Eco-comfort balance 67°F to 74°F 20°C to 23°C

RED

Optimal comfort 75°F to 86°F 24°C to 30°C

FLASHING RED

The baseboard has overheated, and heating has been switched off.

After four minutes, the indicator lights will turn off. Heating will be

restored. If the indicator lights ﬂash repeatedly, make sure nothing

is obstructing the baseboard. Otherwise, contact °STELPRO.

FLASHING YELLOW

The baseboard isn’t operating due to a problem with

thetemperature sensor. Please contact °STELPRO.

FLASHING WHITE

Lock/unlock feature. See the section below.

Limited three-year warranty. See details on www.stelpro.com

* By default, the thermostat is set up for the BRAVA baseboard.

* Celsius version on the back.

VERSION VOLTAGE AND LOAD VOLTAGE RATING

PRODUCT CODE

CELSIUS (°C) OR

FAHRENHEIT (°F)

SUPPLY VOLTAGE

(VAC)

LOAD (W)

OVERVOLTAGE

Summary of content (1 pages)

PAGE 1
INSTALLATION OWNER’S GUIDE OPERATING INSTRUCTIONS 3 BUTTONS TO CONTROL THE TEMPERATURE 1 BUILT-IN ELECTRONIC THERMOSTAT FOR BRAVA AND PRIMA ELECTRIC BASEBOARDS SIBTE12C SIBTE12F SIBTE13C 1-844-STELPRO SIBTE13F 2 PREPARE THE BASEBOARD ASSEMBLE THE THERMOSTAT Press to lower the setpoint temperature by 1° 1. Attach the thermostat using the screws provided. 2. To ensure proper grounding and heat transfer, make sure the thermostat is screwed in securely and is in contact with the junction box cover.