Owner manual

ManualsBrandsSteriflow ManualsEquipmentJSRLP Series

Steriﬂow by Jordan Valve

3170 Wasson Road • Cincinnati, OH 45209

513.533.5600 • 800.543.7311 • 513.871.0105 (f)

steriﬂow@richardsind.com • www.steriﬂowvalve.com

JSRLP Series

Low Pressure Reducing Valves for Bio-Pharm Gas Applications

JSRLP is a high purity gas low pressure regulator designed

and built specically for hygienic, ASME BPE gas applications.

The JSRLP has been designed specically for low pressure

clean gas regulation in Stainless and Single use disposable

applications. Whether it's precise regulation for sparging,

blanketing, motive force, or SUD bag ination, the JSRLP

was built for the job!

The durable valve body and metal trim components are

machined from ASTMA479 316L SST barstock and nished

to ASME BPE SF5 (20Ra micro-inch, electropolished) stan-

dard. The valve is outtted with a thin Jorlon diaphragm and

Teon, PEEK, or EPDM seats and seals that are all FDA

approved, USP Class VI compliant materials. These materi-

als of construction enable JSRLP to withstand the rigors of

an autoclave if required. The EPDM seat reduces lockup to

less than 0.5 psig on this model.

Features

• No exposed threaded connections below diaphragm

• In-line removable seat and trim facilitate cleaning and

routine maintenance

• Barstock construction guarantees material integrity and

surface nish

• Very low lockup with EPDM seat material

• High rangeability and relatively low set point offset

lessens the need for reduced trim sizes

• Minimized internal volume

• Proprietary Jorlon diaphragm material provides excep-

tionally long life and Autoclave capability

• Soft seat material for ANSI Class VI shutoff

• Can be used on continuous clean steam, and on

non-cavitating uids

Documentation

• The following documentation is shipped at no charge:

• Steriow Unicert:

• Certicate of Compliance for:

- Material, including MTR’s

- Surface Finish

- FDA/USP Class VI

• Traceability:

- Each Unicert includes individual valve serial

numbers, heat numbers and attached MTR’s directly

traceable to the valve serial number and heat numbers

imprinted on all wetted metallic components.

surFace Finish

• ASME BPE SF5 (20 Ra micro inch,

electropolished) – standard for all exter-

nal and wetted metal parts

• Other nishes optional

• O

cleaning - optional

applications

Ideal for clean gases used in bio-pharma-

ceutical, and pharmaceutical process.

Designed specically for low pressure con-

trol on traditional Stainless Steel and Single

Use Disposable installations such as: Air or

gas overlay, pressure lling, Lyophilization,

sparging, or SUD bag ination.

• Clean Filter Air

• Nitrogen

• Carbon Dioxide

• Argon

• Oxygen

• Custom purge or blanket gas

Sanitary Valves JSRLP Series Low Pressure Reducing Valves

Summary of content (12 pages)

PAGE 1
Low Pressure Reducing Valves for Bio-Pharm Gas Applications JSRLP is a high purity gas low pressure regulator designed and built specifically for hygienic, ASME BPE gas applications. The JSRLP has been designed specifically for low pressure clean gas regulation in Stainless and Single use disposable applications.
PAGE 2
JSRLP Series High Purity Bio-Pharma Gas Low Pressure Reducing Valve Specifications Sizes: 1/2" (DN15) & 3/4" (DN20) Ends: Clamp, Weld-stub or NPT ends Soft Seat Materials for ANSI Class VI Shut-Off: • PTFE to +252°F (122°C) continuous or 275°F (135°C) intermittent [not to exceed 15 min.
PAGE 3
JSRLP Series High Purity Bio-Pharma Gas Low Pressure Reducing Valve Features & Benefits Optional: • Autoclavable annodized aluminum handle • Handle lockout device Reliable, gas pressure regulation with set points to 1 psig (69 millibar) Fine thread pitch for precision setpoint adjustments SST spring chamber suitable for washdown Large Teflon diaphragm FDA/ USP Class VI approved - for accurate low pressure control down to 1 psi Panel mount and captured vent options available FDA/USP Class VI seat and s
PAGE 4
JSRLP Series High Purity Bio-Pharma Gas Low Pressure Reducing Valve Flow Data for Cv trim selection The graphs illustrate the change or "droop" in outlet pressures as the flow rate increases, and the lockup (setpoint rise) as flow decreases and approaches zero. Flow Coefficient: 0.
PAGE 5
JSRLP Series High Purity Bio-Pharma Gas Low Pressure Reducing Valve Flow Data for Cv trim selection The graphs illustrate the change or "droop" in outlet pressures as the flow rate increases, and the lockup (setpoint rise) as flow decreases and approaches zero. Flow Coefficient: 0.
PAGE 6
JSRLP Series High Purity Bio-Pharma Gas Low Pressure Reducing Valve Flow Data for Cv trim selection The graphs illustrate the change or "droop" in outlet pressures as the flow rate increases, and the lockup (setpoint rise) as flow decreases and approaches zero. Flow Coefficient: 0.
PAGE 7
JSRLP Series High Purity Bio-Pharma Gas Low Pressure Reducing Valve Flow Data for Cv trim selection The graphs illustrate the change or "droop" in outlet pressures as the flow rate increases, and the lockup (setpoint rise) as flow decreases and approaches zero. Flow Coefficient: 0.
PAGE 8
JSRLP Series High Purity Bio-Pharma Gas Low Pressure Reducing Valve Flow Configurations outlet gage A outlet B inlet outlet inlet outlet C inlet outlet gage inlet gage outlet gage D outlet 270° E inlet outlet inlet outlet SAMPLE inlet 90° inlet gage * Gage ports are 1/4" FNPT (consult factory for required alternative) Consult factory for other porting options Sample Specifications Stainless Steel pressure regulator shall be made from ASTM A479 barstock material, which includes body and
PAGE 9
JSRLP Series High Purity Bio-Pharma Gas Low Pressure Reducing Valve Dimensions, In. (mm) — 1/2" & 3/4" Ø5.7 (144,8) 5.89 (149,9) (add 0.75" (19,1) for easy removal 1.25 (33,0) 8.66 (219,9) Dimensions, In. (mm) — 1/2" & 3/4" Ø5.7 (144,8) 5.9 (149,9)* * Add 0.75" (19,1) for easy removal 1.3 (33,0) Weight: 3.2 lbs (1,45 kgs) 3.
PAGE 10
JSRLP Series High Purity Bio-Pharma Gas Low Pressure Reducing Valve Ordering Schematic Model Size Material JSRLP — 050 — 6L JSRLP 1 & 2 3 & 4 5 & 6 7 & 8 9 & 10 11 & 12 13 & 14 Model High Purity Gas Pressure Reducing Valve 11 & 12 SK 050 075 1/2" 3/4" 6L Material Stainless Steel 316L 1&2 Body Feature End Connection Port Configuration C Tri-Clamp 20 Ra EP A Port "A" P FNPT 20 Ra EP B Port "B" T BWE 20 Ra EP C Port "C" D Port "D" E Port "E" ZZ Non-Standard 3&4 1S 2S 1R 2R ZZ Trim 0.8 Cv 0.
PAGE 11
JSRLP Series High Purity Bio-Pharma Gas Low Pressure Reducing Valve Repair Kit Ordering Schematic Model JSRLP JSRLP Size 050 — — Material 6L Model High Purity Gas Pressure Reducing Valve Size 050 075 1/2" 3/4" 6L Material Stainless Steel 316L Kit Kit Repair Kit -11- — Kit Kit 1&2 1P 3&4 ST 1&2 1P 1T 1E 2P 2T 2E ZZ Trim/Seat Material Cv 0.8/PEEK Cv 0.8/PTFE Cv 0.8/EPDM Cv 0.5/PEEK Cv 0.5/PTFE Cv 0.
PAGE 12
JSRLP/0514 Steriflow, a division of Jordan Valve 3170 Wasson Road • Cincinnati, OH 45209 513.533.5600 • 800.543.7311 • 513.871.0105 (f) steriflow@richardsind.com • www.steriflowvalve.com Steriflow Valve reserves the right to make revisions to its product, specifications, literature and related information without notice. Please visit our website at www.steriflowvalve.com for the latest information on our products.