Marine Instruments User's Manual

UNIVERSAL ADVANCED DIGITAL+
4 STEP ALTERNATOR REGULATOR
GREEN: HIGH CHARGE RATE ON
YELLOW: TIMER ACTIVATED
RED ONLY : HIGH BATTERY V TRIP
FLASHING RED: HIGH BATTERY TEMP
HELP LINE FOR STERLING POWER PRODUCTS TEL U.K 01905 26166
GREEN: FLOAT MODE
ORANGE: LOW VOLTAGE WARNING
BATTERY TYPE: GREEN: GEL/SEALED
YELLOW: OPEN LEAD ACID
RED: A.G.I.
BATTERY NEG TRIP FAULT
GREEN:HIGH ALT TEMP DISENGAGE
YELLOW:12 V SYSTEM SETUP
TERLING POWER PRODUCTS
S
CE
1 2
ON
1 2
ON
1 2
ON
BATTERY TYPE
PROGRAM SELECTOR
SWITCH, INSIDE LID
3 BATTERY TYPE
POSITIONS
GEL
SEALED
L.E.D.
( GREEN )
LEAD
OPEN
L.E.D.
( YELLOW )
A.G.M
L.E.D.
( RED )
GREEN: 24 V SYSTEM SETUP
FUSE
POS
NEG
Alternator type
selector inside
control box
Fig.1
Fig.2
a b c d e f g h i j
Setup Up
L.E.D. functions
a
b
c
Bat
ter
y
t
e
mpe
r
atur
e
sens
or
Alternator temperature sensor
Optional connections inside box on P.C.B
ON
1 2 3 4 5 6 7 8 9 10
1 2
ON
TO CONVERT
UNIT FROM 12 VOLT
TO 24 V OPERATION
CONNECT SUPPLIED
PIN JUMPER ACROSS
THESE 2 PINS
Battery
type
selector
REMOTE
PANEL
light
CE
beep
1 2 3 4
2
4
3
1
Sterling power products
Amp
hr
Amps Volts
14.35 v m Pos 4
37amps 435 a/hrs
Sterling power products
CE
alarm
light
temp
System
Low voltage warning System Disengaged System Trip System Within Limits
Screen
Help
Bat 14.4v Timer
Alt 15.4v 134m
set up
volts
d
e
f
h
i
BATTERY
SELECTOR
LED
COLOUR
OPEN
LEAD ACID
GEL-
BATTERIES
(EXIDE SPECIFICATION)
SEALED LEAD
ACID & AGM
GEL & AGM
(USA SPECIFICATION)
ON
1 2
ON
1 2
ON
1 2
ON
1 2
MAX. CHARGING
VOLTAGE
ABSORBTION
TIME
FLOATING
VOLTAGE
YELLOW
GREEN
GREEN-YELLOW
GREEN FLASHING
FOR 5 SEC.
14.8V / 20°C
14.4V / 20°C
14.4V / 20°C
14.1V / 20°C
13.65V / 20°C
13.8V / 20°C
13.65V / 20°C
13.5V / 20°C
1 - 3 HRS.
10 - 12 HRS.
4 - 8 HRS.
4 - 10 HRS.
1 2 3 4
Fig 3
Fig 4
FUSE
POS
NEG
extend cables as require
on/off
Power Management
with
AMP Hr Counter
Advanced Alternator Regulator
Display and
Diagnostics Panel
on/off
Default
light
CE
on/off
beep
1 2 3 4
2
4
3
1
Power Management
with
AMP Hr Counter
Sterling power products
Amp
hr
Amps Volts
14.35 v m Pos 4
37amps 435 a/hrs
Advanced Alternator Regulator
Display and
Diagnostics Panel
Sterling power products
CE
on/off
alarm
light
temp
System
Default
Low voltage warning System Disengaged System Trip System Within Limits
Screen
Help
Bat 14.4v Timer
Alt 15.4v 134m
set up
volts
BAT 14.1V BULK
ALT 14.4V CALC.
BULK CHARGE
WET OPEN
SYSTEM SET: 12V
xxx min. ACTIVE
BAT TEMP: 20C
ALT TEMP: 60C
remote screen information
A
B
THERE ARE 3 DIFFERENT WAYS TO MOUNT THE REMOTE
SLIDE PARTS A TO EXPOSE SCREW HOLES
1) FOR FLUSH MOUNT, REMOVE PART B
2) FOR SURFACE MOUNT KEEP PART B
3) FIT THROUGH A METAL PANEL
AFTER INSTALLATION REPLACE PARTS A
Push the volts button.
this gives the battery voltage and the alternator voltage, this would be
the main screen
Push the arrow button.
this give the charger stage , it bulk charger ( high charger rate ) or float
charger ( job done ), the bulk charger will change to a count down timer
( ie how long before the bulk charger is over and t will beguine ) l it also
gives you the type of battery the system is set up for, ie wet, gel, A.G.M.
etc.
Push button setup.
This gives the system set up information, ie it is set for 12 volt
operation or 24 v , anh the time the system has been active ( engine
running time from start up )
Push button temp.
This gives the battery and alterbnator temperature ( if the sensors are