Installation Guide
Wall Jamb
Top View
Same Distance
Top Track
Clamp Tab
Expansion Mechanism
Wall Jamb
Top Track
Top Track
Cap
Outside
of the
Shower
Expansion
Mechanism
Expansion
Mechanism
Hex
Wrench
x2
Tape
Expansion Mechanism
Outside of
the Shower
Bottom Track
Leg
Correct Incorrect
100% Silicone Sealant
Masking Tape
1205305**
Hanger Bracket Kit
1012706**
Hardware Pack
(5/64")
1013942
1008774
(7/64")
Gasket
1199110
Barrel Nut
1050048-B
#8-32 x 3/8"
8-32 x 1/4"
Screw
1051142-A
Roller
1044585
Hanger Bracket
1199426-01**
Bolt
1077763-A
Door Panel*
1057704-01**
Towel Bar
[18" (457 mm)]
[20" (508 mm)]
[24" (610 mm)]
1057704-02**
1057704-03**
1093027
Spacer (8 ea.)
Series Number Label
(5305EZ-59, 5325EZ-59)
(5325EZ-57, 5375EZ-57)
(5375EZ-47)
(5365EZ-45, 5375EZ-45)
Friction Pad
1008723
Friction Pad
1008723
Guide
1008061**
Fastener
1009982
Bumper
10195.01
1016786-01**
1016786-02**
1016786-03**
(5365EZ)
(5375EZ)
(5325EZ)
(5305EZ)
Wall Jamb
1016786-04**
1016785-04**
1016785-03**
1016785-02**
(5305EZ-59, 5325EZ-59)
(5325EZ-57, 5375EZ-57)
(5375EZ-47)
(5365EZ-45, 5375EZ-45)
Bottom Track
1016785-01**
1204280-04**
1204280-03**
1208525
(1/16")
Hex Wrench
1204280-02**
Top Track Assembly
1204280-01**
Wall Jamb*
Wall Jamb*
Adhesive
Backing
Friction Pad
1"
(25 mm)
Square
End
Contoured
End
IMPORTANT! The wall jamb must rest flat
against the shower ledge and the wall.
Determine which end of the wall jamb will rest
on the shower ledge. Match either the square
or contoured end of the wall jamb to the corner
radius of the shower ledge.
Remove the adhesive backing from both friction
pads. Attach a friction pad to the backside of
each wall jamb approximately 1” (25 mm) above
the shower ledge.
Center the wall jambs on the shower ledge.
Position both wall jambs the same distance from
the front and back edges.
Using a level, plumb both wall jambs. Secure
with masking tape.
Position the bottom track on the shower ledge.
Place the bottom track between both wall jambs
with the bottom track leg facing the outside of
the shower.
Using the large hex wrench (provided), turn the
expansion mechanism toward the inside of the
shower until the bottom track is secure and the
wall jambs are flush against the shower walls.
Slide both caps toward the center of the top track.
Position the top track to rest on top of the wall
jambs with the rounded face toward the outside
of the shower and the expansion mechanism on
the right.
NOTE: The clamp tabs must press the wall
jambs flush against the wall when the top track is
expanded.
When positioning the top track, insert the clamp
tabs against the wall jambs.
Use the large hex wrench (provided) to turn the
expansion mechanism. Expand the top track
until the top track is secure and the wall jambs
are flush against the shower walls. Tighten one
or two additional turns to secure the top track.
Remove the tape from the wall jambs.
Check the bumpers for the correct horizontal
alignment with the wall jambs.
5300EZ Series Sliding Shower and Bath Doors
IMPORTANT! Do not cut the top track the same length as the bottom track.
Walls must be within 3/8” (10 mm) of plumb.
Cover the drain with tape to avoid loss of small parts.
Follow the silicone sealant manufacturer’s instructions for application and
curing time.
For care and cleaning and other information; visit
www.sterlingplumbing.com/care-and-cleaning.
Sliding Shower DoorsSliding Bath Doors
11204891-2-D
USA/Canada: 1-800-STERLING (1-800-783-7546)
México: 001-877-680-1310
1204891-2-D
Installation and Care Instructions
*Call Customer Care Center to order replacement parts.
**Finish/color code must be specifi ed when ordering.
Retain this document for future servicing.
Record model number from box for reference.
Model Number:______________
Required Tools Parts Identifi cation
2 3 4
7 86 9
1 5
10
WARNING: Risk of serious injury. Damage prior to installation can
result in glass shattering. Inspect the glass and all parts for damage
before installation.
WARNING: Risk of serious injury. Improper installation can result
in glass shattering. Follow all installation instructions.
WARNING: Risk of serious injury. Do not cut tempered glass.
Tempered glass will shatter if cut.
WARNING: Risk of serious injury. Shower door and side panels
can shatter. Regularly inspect the glass and all parts for damage,
missing, or loose parts.
WARNING: Risk of serious injury. Always wear safety glasses
while cutting and drilling.
NOTICE: Do not touch the edges of the tempered glass with tools or any
other hard objects. Do not set the unframed tempered glass directly on the
floor or any hard surface.
IMPORTANT! Leave this manual for the end user.
Read these instructions before installing or using this product.
SterlingPlumbing.com