Installation Guide

Wall Jamb
Top View
Same Distance
Top Track
Clamp Tab
Expansion Mechanism
Wall Jamb
Top Track
Top Track
Cap
Outside
of the
Shower
Expansion
Mechanism
Expansion
Mechanism
Hex
Wrench
Tape
Expansion Mechanism
Outside of
the Shower
Bottom Track
Leg
Masking Tape
100% Silicone Sealant
Shop Vacuum
1205305**
Hanger Bracket Kit
1277031-*
Hardware Pack
Gasket
1199110
Barrel Nut
1050048-B
#8-32 x 3/8"
8-32 x 1/4"
Screw
1051142-A
Roller
1044585
Hanger Bracket
1199426-01**
Bolt
1077763-A
Door Panel*
1057704-01**
Towel Bar
[18" (457 mm)]
[20" (508 mm)]
[24" (610 mm)]
1057704-02**
1057704-03**
1093027
Spacer (8 ea.)
Series Number Label
(5305EZ-59, 5325EZ-59)
(5325EZ-57, 5375EZ-57)
(5375EZ-47)
(5365EZ-45, 5375EZ-45)
Friction Pad
1008723
Friction Pad
1008723
Bottom Right
Bumper
1232120-58
Wall Jamb
1233169-03** (5375EZ)
1016785-04**
1016785-03**
1016785-02**
(5305EZ-59, 5325EZ-59)
(5325EZ-57, 5375EZ-57)
(5375EZ-47)
(5365EZ-45, 5375EZ-45)
Bottom Track
1016785-01**
1204280-04**
1204280-03**
1204280-02**
Top Track Assembly
1204280-01**
Wall Jamb*
Guide
1228730**
Bottom Left
Bumper
1232119-58
Top Bumper
1232118-58
1233169-01** (5305EZ)
1233169-02** (5325EZ)
1233169-04** (5365EZ)
1232118-58
Top Bumper
Adhesive
Backing
Friction Pad
1"
(25 mm)
Square
End
Contoured
End
Top
Bumper
Bottom
Bumper
IMPORTANT! The wall jambs must rest flat
against the shower ledge and the wall.
Determine which end of the wall jambs will rest
on the shower ledge. Match either the square or
contoured end of the wall jambs to the corner
radius of the shower ledge.
Remove the adhesive backing from both friction
pads. Attach a friction pad to the backside of
each wall jamb approximately 1” (25 mm) above
the shower ledge.
Center the wall jambs on the shower ledge.
Position both wall jambs the same distance from
the front and back edges.
Using a level, plumb both wall jambs. Secure
with masking tape.
Set the bottom track on the shower ledge.
Position the bottom track between both wall
jambs with the bottom track leg facing the
outside of the shower.
Using the large hex wrench (provided), turn the
expansion mechanism toward the inside of the
shower until the bottom track is secure, and the
wall jambs are flush against the shower walls.
Slide both caps toward the center of the top track.
Position the top track to rest on top of the wall
jambs, with the rounded face toward the outside
of the shower, and the expansion mechanism on
the right.
NOTE: The clamp tabs must press the wall
jambs flush against the wall when the top track is
expanded.
When positioning the top track, insert the clamp
tabs against the wall jambs.
Use the large hex wrench (provided) to turn the
expansion mechanism. Expand the top track
until the top track is secure, and the wall jambs
are flush against the shower walls. Tighten one
or two additional turns to secure the top track.
Remove the tape from the wall jambs.
Press the top and bottom bumpers into place as
shown. Make sure the top bumper tabs press
directly into the triangular pockets in the clamps.
5300EZ Series Sliding Shower and Bath Doors
Sliding Shower DoorsSliding Bath Doors
11278968-2-A
USA/Canada: 1-800-STERLING (1-800-783-7546)
México: 001-877-680-1310
1278968-2-A
Installation and Care Instructions
Required Tools Parts Identifi cation
2 3 4
7 86 9
1 5
10
SterlingPlumbing.com
WARNING: Risk of serious injury. Damage prior to installation can
result in glass shattering. Inspect the glass and all parts for damage
before installation.
WARNING: Risk of serious injury. Improper installation can result
in glass shattering. Follow all installation instructions.
WARNING: Risk of serious injury. Do not cut tempered glass.
Tempered glass will shatter if cut.
WARNING: Risk of serious injury. Shower door and side panels
can shatter. Regularly inspect the glass and all parts for damage,
missing, or loose parts.
WARNING: Risk of serious injury. Always wear safety glasses
while cutting and drilling.
IMPORTANT! Do not touch the edges of the tempered glass with tools or
any other hard objects. Do not set the unframed tempered glass directly on
the floor or any hard surface.
IMPORTANT! Leave this manual for the end user.
Read these instructions before installing or using this product.
IMPORTANT! Do not cut the top track the same length as the bottom track.
NOTICE: The warranty does not apply to a product that has been modified
or altered in a manner other than as expressly permitted in the Installation
and Care Guide.
Walls must be within 3/8” (10 mm) of plumb.
Cover the drain with tape to avoid loss of small parts.
Follow the silicone sealant manufacturer’s instructions for application and
curing time.
To watch this installation online, visit the product page at
www.sterlingplumbing.com.
For care and cleaning and other information; visit
www.sterlingplumbing.com/care-and-cleaning.
Critical Information!
Read Before Installation!
Read and follow all instructions.
*Need help? Contact the STERLING Customer Care Center
at 1-800-STERLING (1-800-783-7546).
For service parts information, care and cleaning, and
other information, visit www.sterlingplumbing.com
**Finish/color code must be specifi ed when ordering.
Retain this document for future servicing.
Record model number from box for reference.
Model Number:______________