Installation Guide

5400 Series Sliding Shower and Bath Doors
Installation Guide
Slide the notched end of the insert into the groove
and pull the notch to the end of the bottom track.
Trim the insert to be flush with the bottom track.
Position the bottom track on the center of the
ledge. If needed, file the ends to match the
corners.
Center the bottom track on the ledge with the leg
to the outside. Tape the bottom track in place and
mark the position.
Position the wall jambs over the bottom track.
Plumb both wall jambs. Mark the screw holes.
Remove the wall jambs. Drill 5/16” holes into the
walls and insert the anchors.
Reposition both wall jambs. Secure the wall jambs
with screws. Attach a bumper at the top and
bottom locations.
*Call Customer Care Center to order replacement parts.
**Finish/color code must be specified when ordering.
Retain this document for future servicing.
Record model number from box for reference.
Important! The bottom track and wall jamb must
sit flat against the shower ledge and the wall. If
needed, trim and file the wall jamb. Use a coin to
match and to transfer the corner radius of the
shower to the wall jamb.
CAUTION: Risk of injury. Do not attempt to cut
tempered glass.
IMPORTANT! Do not cut the top track the same
length as the bottom track.
Walls must be within 3/8" (10 mm) of plumb.
Cover drain with tape to avoid loss of small parts.
Follow the silicone sealant manufacturer's
instructions for application and curing time.
Installation video available at
SterlingPlumbing.com.
Parts Identification
7
89
5
2
3
4
Sliding Shower DoorsSliding Bath Doors
Required Tools
1
6
Model Number:______________
1204884-2-A
Measure distance "A." Subtract 1/4" (6 mm) or
the width of a number 2 pencil from "A" and cut
the bottom track.
Apply silicone sealant in the groove on the
underside of the bottom track. Secure the bottom
track to the ledge along the marked location.
100% Silicone Sealant Masking Tape
32 Teeth Per Inch Blade
Miter Box
Number 2 Pencil
3/16"
5/16" Masonry Bit for Tile
5/16"
Door Panel*
Wall Jamb*
Series Number Label
1077762
Anchor
1081001
Bumper
1031943**
Screw Cover
1058827-02**
Top Track
1093027
Spacer (8 ea.)
Bottom Wall
Jamb Notch
1053530
Insert
Wall Jamb*
1056868-A
Screw
1058294**
Center Guide
1048208-C
#8-18 x 1-1/2"
1058626-02**
Bottom Track
Bottom Wall
Jamb Notch
Insert
1/4" (6 mm)
Cut Line
"A" Mark
Leg
Notch
1
2
3
Screw Cover
Screw Cover
#8-18 x 1-1/2"
A
A
Groove
Bottom Track
Screw
Tin Snips
1
USA: 1-800-STERLING (1-800-783-7546)
Mexico: 001-877-680-1310
SterlingPlumbing.com
Gasket
1199110
Barrel Nut
1050048-B
#8-32 x 3/8"
8-32 x 1/4"
Screw
1051142-A
Roller
1044585
Hanger Bracket
1199426-01**
Sex Bolt
1077763-A
x2
x2
x2
1/16"
1057704-02**
[24" (610 mm)]
[20" (508 mm)]
Towel Bar
1057704-01**
1203633
Hardware Skin Pack
1205305**
Hanger Bracket Kit