Installation Sheet

Bottom
Track
Sealant
x2
3
2
1
x2
B
Face
Notch
Center Guide
Sealant
Tin Snips
5/16"
5/16" Masonry Bit for Tile
3/16"
Miter Box
32 Teeth Per Inch Blade
Masking Tape
100% Silicone Sealant
File
5/16"
Sliding Bath Doors Sliding Shower Doors
Wall Jamb
1226713-01**
[55-1/16" (1403 mm)]
1226713-02**
[68-13/16" (1753 mm)]
Screw
Screw
1048208-H
#8-32 x 3/8"
1052906-A
Outside Panel
1222640** [59" (1499 mm)]
1222642**
[48" (1219 mm)]
#8-18 x 3/4"
1216554**
Towel Bar Bracket
1077762
Anchor
1081001
Bumper
1031943**
Screw Cap
#8-18 x 1-1/2"
Inside Panel
Center Guide
1217372**
Seal
1198133-01**
Roller
172818
1031943**
Screw Cap
1048208-C
Screw
1216373-02**
Towel Bar
1216373-01**
[22-5/16" (567 mm)]
[27-1/2" (699 mm)]
1217369-01**
Bottom Track
[59-1/4" (1505 mm)]
1219845-01**
Top Track
1222643**
[59" (1499 mm)]
1222645**
[48" (1219 mm)]
[60" (1524 mm)]
Guide/Bracket Skin Pack
Hardware Skin Pack
1218488**
1218485
1/4" (6 mm)
Cut Line
"A" Mark
A
A
x2
Measure distance "A." Subtract 1/4” (6 mm) or
the width of a number 2 pencil from “A;” mark
and cut the bottom track.
If needed file the bottom track edges to fit the
curved corners of the shower or bath unit.
If the threshold is uneven, bend the bottom track
to conform to the threshold to eliminate gaps.
Center the bottom track on the ledge with the
front face to the outside. Mark the location of the
bottom track.
IMPORTANT! The bottom track and wall jamb
must sit flat against the shower ledge and the
wall. If needed, trim and file the wall jamb. Use
a coin to match and to transfer the corner radius
of the shower to the wall jamb.
Position the wall jambs over the bottom track.
Plumb both wall jambs using a level. Secure
with tape. Confirm "B" is the same for both wall
jambs.
Recheck plumb using a level. For each screw
hole, mark the locations or drill a pilot hole at
each spot.
Remove the wall jambs. Drill 5/16” holes into
the walls and insert the anchors.
Apply sealant on the underside of the bottom
track along the entire length. Position the track
on the ledge at the marks with an even gap on
each side.
Determine the centerline of the bottom track.
Apply silicone sealant to the bottom of the center
guide. Install the center guide centered on the
bottom track.
Sliding Shower Door
572005, 572075
1
1225437-2-B
USA/Canada: 1-800-STERLING (1-800-783-7546)
México: 001-877-680-4537
SterlingPlumbing.com
1225437-2-B
Installation and Care Instructions
Required Tools Parts Identifi cation
2 3 4
7 86 9
1 5
10
WARNING: Risk of serious injury. Damage prior to
installation can result in glass shattering. Inspect the
glass and all parts for damage before installation.
WARNING: Risk of serious injury. Improper
installation can result in glass shattering. Follow all
installation instructions.
WARNING: Risk of serious injury. Do not cut
tempered glass. Tempered glass will shatter if cut.
WARNING: Risk of serious injury. Shower door and
side panels can shatter. Regularly inspect the glass and
all parts for damage, missing, or loose parts.
WARNING: Risk of serious injury. Always wear safety
glasses while cutting and drilling.
IMPORTANT! Do not touch the edges of the tempered glass
with tools or any other hard objects. Do not set the unframed
tempered glass directly on the floor or any hard surface.
IMPORTANT! Leave this manual for the end user.
Read these instructions before installing or using this product.
IMPORTANT! Do not cut the top track the same length as the
bottom track.
NOTICE: The warranty does not apply to a product that has
been modified or altered in a manner other than as expressly
permitted in the Installation and Care Guide.
Walls must be within 3/8” (10 mm) of plumb.
Cover the drain with tape to avoid loss of small parts.
Follow the silicone sealant manufacturer’s instructions for
application and curing time.
To watch this installation online, visit the product page at
www.sterlingplumbing.com.
For care and cleaning and other information; visit
www.sterlingplumbing.com/care-and-cleaning.
Critical Information!
Read Before Installation!
Read and follow all instructions.
*Need help? Contact the STERLING Customer Care Center
at 1-800-STERLING (1-800-783-7546).
For service parts information, care and cleaning, and
other information, visit www.sterlingplumbing.com
**Finish/color code must be specifi ed when ordering.
Retain this document for future servicing.
Record model number from box for reference.
Model Number:______________