Installation Guide

Tin Snips
Miter Box
32 Teeth Per Inch Blade
Masking Tape
100% Silicone Sealant
3/16", 5/16"3/16", 5/16"
5/16" Masonry Bit for Tile
1077762
Anchor
1031943**
Screw Cap
Center Guide
1217372**
Seal
1198133-01**
1048208-C
Screw
#8-18 x 1-1/2"
1217369-01**
Bottom Track
[59-1/4" (1505 mm)]
1235382**
Bracket Skin Pack
[60" (1524 mm)]
1235467
Hardware Skin Pack
1205305**
Hanger Bracket Skin Pack
Gasket
1199110
Screw
#8-32 x 3/8"
1051142-A
Roller
1217402
Hanger Bracket
1199426-01**
Serial Number Label
1232502-01**
Top Track
Bottom Wall
Jamb Notch
Wall Jamb
1225691-01**
1225691-02**
[53-7/8" (1368 mm)]
[68-7/16" (1738 mm)]
Panel
1232549**
1232550**
1232551**
1234156**
Bracket
1231700**
Bushing
1235581-A
Screw
#10 Hi-lo
1226405**
Cover
Left Bumper
1233092**
Top Bumper
1224786
Right Bumper
1233091**
Bolt
1077763-A
Blind Nut
1050048-B
[19" (483 mm)]
[23" (584 mm)]
Towel Bar
1238077-01**
1238077-02**
1/4" (6 mm)
Cut Line
"A" Mark
A
A
x2
x2
B
Notch
x2
3
2
1
Bottom
Track
Sealant
Face
Center Guide
Sealant
Sliding Shower and Bath Doors
IMPORTANT! Do not cut the top track the same length as the
bottom track.
Walls must be within 3/8” (10 mm) of plumb.
Cover the drain with tape to avoid loss of small parts.
Follow the silicone sealant manufacturer’s instructions for
application and curing time.
Measure distance “A.” Subtract 1/4” (6 mm) or the
width of a number 2 pencil from “A;” mark and cut the
bottom track.
If needed file the bottom track edges to fit the curved
corners of the shower or bath unit.
If the threshold is uneven, bend the bottom track to
conform to the threshold to eliminate gaps.
Center the bottom track on the ledge with the front face
to the outside. Mark the location of the bottom track
and secure with tape.
IMPORTANT! The bottom track and wall jamb must
sit flat against the shower ledge and the wall. Use a
coin to match and to transfer the corner radius of the
shower to the wall jamb.
Position the wall jambs over the bottom track. Plumb
both wall jambs using a level. Secure with tape. Confirm
“B” is the same for both wall jambs.
Recheck plumb using a level. For each screw hole, mark
the locations or drill a pilot hole at each spot.
Remove the wall jambs. Drill 5/16” holes into the walls
and insert the anchors.
Apply sealant on the underside of the bottom track
along the entire length. Position the track on the ledge
at the marks with an even gap on each side.
Determine the centerline of the bottom track. Apply
silicone sealant to the bottom of the center guide. Install
the center guide centered on the bottom track.
Sliding Bath Doors Sliding Shower Doors
1
1241585-2-A
Installation and Care Instructions
*Call Customer Care Center to order replacement parts.
**Finish/color code must be specifi ed when ordering.
Retain this document for future servicing.
Record model number from box for reference.
Model Number:______________
Required Tools Parts Identifi cation
581005, 581075
WARNING: Risk of serious injury. Damage prior to
installation can result in glass shattering. Inspect the glass
and all parts for damage before installation.
WARNING: Risk of serious injury. Improper
installation can result in glass shattering. Follow all
installation instructions.
WARNING: Risk of serious injury. Do not cut tempered
glass. Tempered glass will shatter if cut.
WARNING: Risk of serious injury. Shower door and
side panels can shatter. Regularly inspect the glass and all
parts for damage, missing, or loose parts.
WARNING: Risk of serious injury. Always wear safety
glasses while cutting and drilling.
NOTICE: Do not touch the edges of the tempered glass with
tools or any other hard objects. Do not set the unframed
tempered glass directly on the floor or any hard surface.
IMPORTANT! Leave this manual for the end user.
Read these instructions before installing or using this product.
1 2
7
3
86
4
9
5
10
1241585-2-A
USA/Canada: 1-800-STERLING (1-800-783-7546)
México: 001-877-680-1310
SterlingPlumbing.com