SMS Medium Duty Single Shaft Shredder SMS 850, 1200, 1500, 2000 Part Number: ESS-0039-S Bulletin Number: BJ5-615 Effective: 9.30.2008 Write Down Your Serial Numbers Here For Future Reference: _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ We are committed to a continuing program of product improvement.
Shipping Info Unpacking and Inspection You should inspect your equipment for possible shipping damage. Thoroughly check the equipment for any damage that might have occurred in transit, such as broken or loose wiring and components, loose hardware and mounting screws, etc. In the Event of Shipping Damage According to the contract terms and conditions of the Carrier, the responsibility of the Shipper ends at the time and place of shipment.
Storage, Disposal, Transportation Storage Clean the machine (see “Cleaning the Machine”). Preserve all polished metal surfaces using a suitable rust preventing agent. Store the machine in a dry, enclosed space. Cover the machine completely with a plastic sheet. Disposal The disposal of machines, machine components, and process materials is partially subject to legal controls. More detailed information is given at the relevant administrative authority (i.e.
Table of Contents CHAPTER 1: SAFETY................................................................ 5 1-1 1-2 1-3 1-4 How to Use This Manual ............................................................................................. 5 Safety Symbols Used in this Manual .....................................................................5 General Safety Regulations ........................................................................................ 6 Responsibility ...................................
Chapter 1: Safety 1-1 How to Use This Manual Use this manual as a guide and reference for installing, operating, and maintaining your equipment. The purpose is to assist you in applying efficient, proven techniques that enhance equipment productivity. This manual covers only light corrective maintenance. No other maintenance should be undertaken without first contacting a service engineer. The Functional Description section outlines models covered, standard features, and safety features.
1-2 General Safety Regulations This machine uses cutters for the performance of its intended use. Consequently, it can be a dangerous machine to operate and maintain unless these safety regulations are followed. These regulations should be read, understood and periodically reviewed by all personnel involved in any way with this machine. Never operate or remove any machine components that are secured by wrench-type fasteners unless the motor is electrically locked out and the rotor is motionless.
1-4 Warnings and Precautions Our granulators are designed to provide safe and reliable operation when installed and operated within design specifications, following national and local safety codes. To avoid possible personal injury or equipment damage when installing, operating, or maintaining this granulator, use good judgment and follow these safe practices: ; LEARN AND OBEY your company’s safety policy regarding granulating equipment.
; ROTATION OF MOTORS: The correct rotating direction for the machine motor is clearly marked on the machine. Always check for proper rotation of motors. Incorrect rotation direction can cause severe damage. ; ELECTRICAL GROUNDING: All electrical equipment on the granulator must be grounded in accordance to all local codes and Article 250 of the National Electric Code. ; ALWAYS DISCONNECT AND LOCKOUT the main electrical power to the granulator before performing any service.
Type of Danger Activity Possible Consequences Preventative Measures Pulling in caused by running V-belts All activities Serious injury can result from hair, jewelry, etc. being pulled into the machine. • Never dismount V-belt protection and window. Direct/indirect contact with live parts in terminal box. Maintenance work, start up Serious injury or death • Only trained electricians may carry out all work on the electrical equipment.
Type of Danger Activity Possible Consequences Preventative Measures Crushing, cutting, amputation caused by manipulation of protective devices All activities Serious injury or death • Never make the protective devices ineffective. • Check the protective devices regularly for proper function according to the manual’s specifications.
Chapter 2: Functional Description 2-1 Models Covered in This Manual The models included in this manual are the Sterling SMS 850, 1200, 1500 and 2000 Medium Duty Single Shaft Shredders. The SMS Series is designed for processing scrap from wood industries—miscellaneous trim and panel scraps, furniture, injection and extrusion mold start-up purge, heavy wall parts, paper and cardboard, and film (baled and loose).
Machine (Standard Execution) (1) (2) (3) (4) (5) (6) (7) (8) Base Frame Machine door Hopper door Gear Box Drive motor V-belt guards Ram hydraulic guards Discharge area 3 7 4 2 6 5 8 1 The machine housing, drive motor, gear box, hydraulic system and terminal box are mounted on the base frame for electrical connections.
In-feed Hopper The material in-feed flows through an in-feed hopper to ensure the grinding material is delivered safely and correctly. NOTE: An optional top-hinged cover to prevent in-feed material fly-back during size reduction is available. Special hopper with hydraulic cover Additional In-feed Device If the machine has an optional in-feed device such as a conveyor belt, please refer to the additional information about the accessory in the manufacturer’s manual that accompanied the accessory.
Drive The drive of the rotor runs using an electric motor via V-belts. The motor (mounted on sliding rails or a motor plate) can be adjusted for regulating the tension of the V-belts using tensioning screws. The V-belt pulley is attached to the motor shaft with a special tensioning element.
1 3 (1) Rotor cutter (2) Screen support (hydraulic) (3) Bed cutter 2 (1) Rotor cutter (2) Screen support 1 2 The rotor is accessible after opening the machine door and removing the screen. The rotor is arranged on roller bearings that situated outside the housing. The V-belt pulley is attached to the rotor axis with a taper brush. The rotor is dynamically counterbalanced and has vibration-free concentricity.
An optional feature is a water cooling system for the rotor used for special applications. Bearing with water plug for rotor cooling Screen and screen support The screen and the screen support are welded together and fixed to the housing by screws in the standard execution. The screen is slightly larger in radius than the cutting circle of the rotor cutters. The screen perforation is selected according to the desired grain size of the grinding material.
Another optional feature is a screen support that can be lowered by a hydraulic system. (1) Hydraulic cylinder (2) Screen support (3) Screen 3 1 2 Discharge of Shredding Material Normally the shredded material will be discharged onto a conveyor belt. (Options include a discharge with blower or with a screw conveyor.
Hydraulic Ram The hydraulic ram is fixed on two arms arranged on flange bearings. Two heavy duty hydraulic cylinders move the ram back and forth. The ram moves automatically after switching ON the hydraulic system and the shredder when the machine is operated in automatic mode. NOTE: The ram can be moved by hand on the control panel when run in manual mode.
Pulse Push Function In normal process mode, the ram pushes forward continuously until the ram arm reaches the proximity switch, reverses the function, and the ram moves backwards. The ram moves forward in steps when the switch (1) is changed to “Pulse Push”. This means that after each step, the ram remains in position for a couple of seconds before it moves forward again. This function should be used for very heavy applications and when overloading the system is a concern.
2-4 Safety Features Protective Devices CAUTION: The Machine may under no circumstances be operated without these protective devices. The use of faulty or manipulated protective devices is strongly prohibited. Safety Device for Housing Flap Safety device: machine door Safety device: hopper door The shredder can only be operated if the doors are closed—deactivating the safety switch. The safety contact is broken when the machine or hopper door is open, thus switching off the machine.
V-Belts and Ram Guards V-belt and ram guards are screwed to the machine. They can be dismounted for installation and maintenance work only when all rotating parts have come to a complete standstill and the machine is electronically locked out. 1 (1) Ram guarding (2) V-belt guarding 2 NOTE: The operator must fit and mount the protective devices delivered with the machine according to current legal safety regulations if a machine is delivered without drive motors per request of the customer.
The following protective gear must be worn when carrying out the following tasks: Unloading machine. Connecting machine. Operation. Cleaning. Maintenance of bearings. Screen replacement. Maintenance of V-belts. Maintenance of cutting cutters. Cutter sharpening. Safety helmet x Safety boots x x x x x x x x Safety gloves x x Safety goggles x x Ear muffs x x x x x x x x Emergency Stop Button The machine may only be operated with the installed Emergency Stop buttons.
Chapter 3: Installation 3-1 Uncrating the Equipment Requirements at Application Site Check the application site to make sure it conforms to the qualifications listed below. • The site is an enclosed space. • • • • • • • • • • The ground has sufficient load-bearing capacity (Refer to “Technical Specifications” in the Appendix for machine weight). The unevenness of the ground surface may not exceed 5 mm. The machine must be freely accessible from all sides.
WARNING! SUSPENDED LOAD! • Falling loads can cause serious injury or death. • Only use a crane or forklift suitable for the weight and the dimensions of the load. • Use suitable stopping equipment and pay attention to the gravity center location. • DO NOT step under the suspended load. • Wear a safety helmet in addition to basic protective gear. WARNING! OVERTURNING OR FALLING MACHINE! • Serious injury or death can result.
WARNING! Use caution when operating specific equipment to prevent electrical shock. Installation, service, alterations, and/or modifications must only be done by qualified personnel and with high regard for safety. Not conforming to the requirements could result in bodily harm, death, or costly damage. NOTE: Alterations to the wiring diagrams require approval. Failure to do this will exclude all guarantee claims. The wiring schematics are located in the control panel.
Checking the Rotational Direction Rotational direction of the motors must be checked before initial start-up. The following steps must be completed. 1. Switch the machine ON and then immediately OFF again. 2. Observe whether the discharge air fan in the drive motor is rotating in the direction of the direction arrow. NOTE: If running in the wrong direction, reconnect the motor connection immediately. Damage to the machine will result from operation in the wrong direction.
9 Switch ON machine for a short period of time and check rotational direction. The rotational direction can be seen at the discharge air fan of the drive motor (observe running direction arrow). 9 Switch ON hydraulic unit for a short time and check rotational direction. 9 Allow machine to run for approximately 10 minutes without shredding material. 9 Connect material discharge device and in-feed device; check rotational direction drives. 9 Feed grinding material uniformly.
Chapter 4: Operation 4-1 Start-up WARNING! No persons should operate the machine until they have read and understand all parts of the operation manual. Machine Check—Before Switching Machine ON 9 Cutters and bed knives are properly set and the screws are tightened with the specified torque. 9 Screen is inserted into the screen support according to the instructions, and the screen support is fixed at the end position with tightened mounting screws. 9 The cutting chamber is free of foreign matter.
• Throw the grinding material into the in-feed hopper. • The machine should be fed from the front. • If your machine has an additional in-feed device installed, please observe the additional information for working with the in-feed device. DANGER! Do not climb into the in-feed hopper while operating the machine. Death will result. Emptying the Screen (standard screen) 1. Switch OFF the shredder at the main switch 2. Safeguard main switch using a padlock. 3. Open the machine door. 4.
Emptying the Screen (hydraulic screen) 1. Switch OFF the shredder at the main switch. 2. Safeguard main switch using a padlock. 3. Open the lower machine door. 4. Safeguard the machine door. 5. Pivot the screen support downwards by pushing the button screen open on the control box. 6. Remove the screen. 7. Empty the screen. 8. Put the screen back into the screen support. 9. Pivot the screen support into the working position and fasten using the mounting screws. 10. Close the machine door. 11.
4-3 Shut-down Switch OFF Machine 1. Switch OFF the material in-feed device (accessories). 2. Wait until the remaining grinding material has been shredded, and then switch OFF the shredder (main switch to 0). 3. Switch OFF the material discharge device.
Chapter 5: Maintenance 5-1 Preventative Maintenance Schedule Only trained and specialized personnel should carry out maintenance work. Maintenance Plan WARNING! • Danger caused by electrical voltage and starting the machine during maintenance work. Death can result! • ALWAYS turn main switch to 0, safeguard using a padlock, and attach a warning sign while carrying out maintenance work. The tasks for maintenance work are described below.
5-2 Preventative and Corrective Maintenance Checking the Protective Devices Check the safety devices for: • Stipulated condition • Stipulated location • Safe mounting • Stipulated function WARNING! Danger due to non-functioning protective devices can cause serious injury or death! • Eliminate all defects before operating the machine! • If defects occur during operation, stop the machine immediately and eliminate the defects! • Do NOT change or remove any protective devices.
10. Place the screen back into its working position and fasten with the mounting screws. 11. Close the machine and hopper doors. 12. Machine can be started again. Replacing the Gear Box The gearbox is made so a replacement is only necessary in exceptional cases. Dismounting and mounting the gear box requires specialist knowledge and a careful working method. Please observe the instructions given in the installation manual of the gear box manufacturer or ask the service department for help.
9. Carry out a test run. NOTE: If the spare rotor is delivered without bearings, the bearings MUST be mounted first. Replacing the Main Bearings The main bearings of the machine are made so a bearing replacement is only necessary in exceptional cases. Dismounting and mounting of the bearings requires specialist knowledge and a careful working method.
5. Attach the bearing housing to the bearing seats using screws. 6. Push the distance sleeve onto the rotor axis. 7. Put the gear onto the rotor axis 8. Put back the rotor cover plates 9. Put in the screen 10. Pull on V-belts and adjust the V-belt tension force. 11. Attach the V-belt cover. 12. Carry out a test run. NOTE: • The roller bodies will be damaged unless the mounting forces engaged into inner ring. • The hardened bearing rings are sensitive to impact stress; never hit the rings with the hammer.
Replacing or Refilling Lubricant • Fill the bearings uniformly with grease until all operating surfaces are well-greased. • For the rotor bearings, a lubricant quantity of one third to a maximum of half of the bearing volume per bearing is required. If too much grease is used, the lubricant will become unusable due to excessive temperature. • Only one type of grease may be used, mixing different types of grease is prohibited.
out, the bearing must immediately be preserved using lubricant, in order to avoid corrosion. 4. Fill bearing with approved lubricant (refer to “List of Lubricants”).
Mounting and Dismounting TAPER-LOCK Tensioning Element The motor and the gear V-belt pulleys are attached to the shaft using a TAPER-LOCK tensioning element. The disks must be dismounted for certain maintenance processes.
Tightening Torque of the Screws Refer to the table below.
Checking the tension force of the V-belt 1. Remove the V-belt cover. 2. Measure the distance between the roller centers. 3. Determine the belt sag force F for each belt at 16 mm sag if sag "b" is equal to 1 m distance between roller centers. Do this by measuring the distance between roller centers at a right angle to the V-belt.
3. Lock the drive motor into new position using tensioning screws so the motor shaft is parallel to the rotor axis and aligned. 4. Check the tension force of the V-belt (refer to previous section). 5. Mount the V-belt cover. Checking V-belt condition, replacing V-belt CAUTION! Running V-belts can pull objects into the machine! Hair, jewelry etc. can be pulled into machine without proper precaution resulting in serious injury. NEVER dismount the V-belt cover and window during operation.
Torque Screw type Grade 8.8 M8 M10 M12 M16 M20 M24 Nm 25 49 86 210 410 710 lbf ft 18.4 36.1 63.4 154 302 523 Grade 10.9 Nm 35 69 120 295 580 1000 lbf ft 25.8 50.9 88.5 217 428 737 Grade 12.9 Nm 41 83 145 355 690 1200 lbf ft 30.2 61.2 106 261 508 885 Checking the Condition of the Cutters WARNING! Danger of cutting caused by sharp cutters at all times—even when rotor is at standstill. Serious Injury especially to the hands and fingers can occur.
1 (1) (2) (3) (4) Cutter Cutter mounting screw Cutter holder Cutter holder mounting screws 4 2 3 Dismounting the Cutter Holders 1. Switch OFF the shredder at the main switch 2. Safeguard main switch using a padlock. 3. Open the lower machine door. 4. Safeguard the machine door. 5. Remove screen NOTE: Although it is possible to reach the cutting shaft by climbing into the feeding chamber, it is recommended to access the cutters through the machine door located at the front of the machine.
WARNING! Danger of cutting caused by sharp cutters at all times—even when rotor is at standstill. Serious Injury especially to the hands and fingers can occur. Wear protective gloves! Dismounting the Bed Cutters 1. Switch OFF the shredder at the main switch. 2. Safeguard main switch using a padlock. 3. Open the upper hopper door. 4. Safeguard the hopper door.
WARNING! Danger of cutting caused by sharp cutters at all times—even when rotor is at standstill. Serious Injury especially to the hands and fingers can occur. Wear protective gloves! 6 (1) (2) (3) (4) (5) Bed knife Knife mounting screws Knife holder Cover plates Knife adjusting screw for pushing (6) Cutter adjusting screw for pulling (7) Cover plate mounting screws 5 2 3 4 1 7 Mounting the Cutter Holders 1. Clean the cutter pocket and the cutter holder. 2. Insert cutter holder into the pocket.
Mounting the Cutters 1. Clean the cutter supporting surface and the hole on the cutter holder. 2. Insert sharp cutter or turn old cutter, and push against the cutter holder surface. 3. Put in the cutter mounting screw (DIN912 – M12x40 – 12.9) and the washer (DIN433 – 13 – 300HV). 4. Screw in the mounting screws and tighten lightly first. 5. Make sure the cutter fits planar in the seat. 6. Tighten the cutter mounting screws using a torque wrench.
7. Turn the rotor by hand 8. Check whether the cutting gap is correct and make sure the cutting cutters do not collide as the rotor turns. 9. Put back the cover plates and mount them with the screws. 10. Remove tools and other objects from the cutting chamber. 11. Put screen back and mount it. 12. Switch ON the shredder for a short time without grinding material and listen for noises. If there are unusual noises, determine the cause and eliminate it.
WARNING! Danger of cutting caused by sharp cutters at all times—even when rotor is at standstill. Serious Injury especially to the hands and fingers can occur. Wear protective gloves! Setting the Cutting Knives Cutters for the SMS series shredder do not have to be adjusted. All adjustments have to be done with the bed cutters. To simplify cutter setting and shorten standstill periods when replacing cutters, bed cutters have 4 adjusting screws, 2 each for pushing and pulling the cutter.
NOTE: The required torque for all cutter mounting screws is 120 Nm (see the table under “Working on the Cutters”). 7. Turn the rotor by hand 8. Check whether the cutting gap is correct and make sure the cutters and bed knives do not collide as the rotor turns. NOTE: Recommended cutter gap: 0.8 mm – 1 mm 9. Mount the cutter cover plates. Transporting and Storing the Cutting Cutters WARNING! • • • • • Danger of cutting caused by sharp cutting cutters.
Checking and Adjusting of the Hydraulic System (see figure below) 1. Start the machine in automatic running mode and wait for approximately 20 minutes. 2. When the ram moves forward the pressure gauge (1) should indicate 0 – 30 bars depends on the adjustment of the throttle check valves (2). (Also adjust the speed of the ram with this valve.) 3. When the ram moves backwards the pressure gauge (1) should indicate 0 – 30 bars depends on the adjustment of the throttle check valves (2). 4.
Hydraulic liquid recommendation Designation to DIN 51 524 HLP 32 Ambient temperature: -7 to +70°C Supplier Name of the oil ARAL Aral Vitam GF 32 Aral Vitam HF 32 BP Energol HLP-D 32 BP Energol HLP 32 BP Energol SHF 32 Elfolna 32 Hydrelf 32 Nuto H 32 HLPD-Oel 32 Fina Hydran 32 Renolin MR 10 Renolin B 10 Mobil DTE 24 Mobil DTE 17 Drucköl HLP 32 - C Hydrauliköl HLPD 32 Rando Oil HD A - 32 Rando Oil HD AZ - 32 Alcor Oil DD 32 BP ELF ESSO FINA FUCHS MOBIL TEXACO BJ5-615 Chapter 5: Maintenance 52 of
Chapter 6: Troubleshooting 6-1 Introduction The utmost in safety precautions should be observed at all times when working on or around the machine and the electrical components. All normal troubleshooting must be accomplished with the power off, line fuses removed, and with the machine tagged as out of service. The use of good quality test equipment cannot be over-emphasized when troubleshooting is indicated.
Problem Machine blocks or switches itself off Possible Cause Possible Remedy Too much feed material. Reduce grinding material infeed. Screen blocked. Clean screen, check condition, select larger screen perforation if necessary. V-belts slip. Check V-belt tension and condition. Re-tighten or replace if necessary. Cutter condition. Check cutters and resharpen or replace if necessary. Cutting gap. Check cutting gap and set following the instructions in this manual. Discharge blocked.
Problem Overheating of the shredded material. Unusual vibrations. Possible Cause Possible Remedy View first 5 possible causes for “Machine blocks or switches itself off” View first 5 possible remedies of “Machine blocks or switches itself off” Screen perforation too small. Insert a screen with larger perforation. Cutters wrongly sharpened. Modify cutter finish only after consulting the service department. Material rubs against the housing wall. Fit anti-winding device. Insufficient cooling.
Problem Cutting gap alters during operation. Screen damage. Shredder does not start. Shredder blocks when under load. Possible Cause Possible Remedy Cutter mounting screws not tight. Re-tighten using torque wrench following the instructions in this manual. Screw fatigue. Fit new screws. Washers deformed. Insert new washers. Cutter holder surface deformed. Insert new cutter holders. Supporting surfaces not clean. Clean and re-dust supporting surfaces. Threads in housing worn.
Appendix A-1 Returned Material Policy Credit Returns Prior to the return of any material, authorization must be given by the manufacturer. A RMA number will be assigned for the equipment to be returned. Reason for requesting the return must be given. All returned material purchased from the manufacturer is subject to 15% (75.00 minimum) restocking charge. All returns are to be shipped prepaid. The invoice number and date or purchase order number and date must supplied.
A-2 BJ5-615 Technical Specifications 0Appendix 58 of 85
A-3 Drawings and Diagrams NOTE: Please refer to the corresponding Spare Parts lists in the following section.
Bed Knife Mounting BJ5-615 0Appendix 60 of 85
Rotor Assembly BJ5-615 0Appendix 61 of 85
Drive BJ5-615 0Appendix 62 of 85
Ram BJ5-615 0Appendix 63 of 85
Ram scraper BJ5-615 0Appendix 64 of 85
SMS 850 Hydraulic Diagram BJ5-615 0Appendix 65 of 85
SMS 850 Hydraulic Unit BJ5-615 0Appendix 66 of 85
SMS 850 Hydraulic Screen Diagram BJ5-615 0Appendix 67 of 85
SMS 850 Hydraulic Unit—Screen BJ5-615 0Appendix 68 of 85
SMS 1200-2000 Standard Hydraulic Diagram BJ5-615 0Appendix 69 of 85
SMS 1200-2000 Hydraulic Unit BJ5-615 0Appendix 70 of 85
SMS 1200-2000 Hydraulic Screen Diagram BJ5-615 0Appendix 71 of 85
SMS 1200-2000 Hydraulic Unit BJ5-615 0Appendix 72 of 85
A-4 Spare Parts List SMS 850 Pos. 100 101 102 103 104 105 106 107 108 109 1 2 1 1 1 2 1 1 1 Description/Standard Machine complete Standard hopper PP-scraper side PP-scraper top Upper door Lower door Safety grid side Safety grid back Safety grid back Ram residual chute 200 201 202 203 204 205 206 207 208 1 5 5 5 2 2 2 2 Screen complete (Standard) Screen Screen support screws DIN912-M12x35-8.8 Washer DIN125-B-13-140HV Spring washer DIN127-A -13 Clamp Clamp mounting screws DIN933-M20x40-8.
BJ5-615 404 405 1 4 406 1 407 1 408 409 410 411 412 413 414 415 416 417 1 1 1 1 1 1 1 1 1 1 500 501 502 1 60 60 503 504 505 60 60 120 600 601 602 603 2 6 12 6 604 6 605 12 606 607 1 1 1 12 700 701 702 703 1 2 2 8 704 705 706 707 708 709 710 711 712 2 1 12 12 12 12 12 1 4 Gear pulley taper bushing TB 3535-50 Key C 28x250 V-Belt SPB 2150 V-Belt SPC 2430 Motor pulley SPB 224-4 Motor pulley SPC 250-4 Motor pulley taper bushing TB 3020-60 Motor pulley taper bushing TB 3535-65 Key Motor
713 714 715 716 1 2 2 8 717 4 800 801 802 803 804 805 806 900 901 902 903 904 905 Cover plate for scraper Upper cylinder screw Lower screw for cylinder mounting Mounting screw for cylinder screw DIN912 – M16x25 – 12.9 Grease nipple GB1152/M10x1 1 1 1 Hydraulic Cylinder for ram ø35xø70x420 Piping Connectors Hydraulic unit 3.
300 2 Bearing 301 302 303 304 305 306 307 308 309 2 2 2 1 1 3 2 2 24 Bearing housing SN324 Bearing GB/T288-94-22324 Bearing Cover A Bearing Cover B Bearing housing cover plate Sealing GB9877.1-86 J150x180x15 Grease nipple GB1152-89/M8x1 Sleeve Ø150x16 Mounting screw cover plate DIN912-M10x40-8.8 Mounting screw cover plate DIN912-M10x45-8.8 Bearing mounting plate Mounting plate screw DIN912 – M24x50 – 8.
604 8 605 16 606 607 2 1 1 16 700 701 702 703 1 2 2 8 704 705 706 2 1 12 707 708 709 710 711 712 12 12 12 12 1 4 713 714 715 716 1 2 2 8 717 4 800 801 802 803 804 805 806 900 901 902 903 904 905 Upper bed knife adjusting screw for pushing DIN912 – M16x45 – 12.9 Bed knife adjusting screw for pulling DIN912 – M16x60 – 12.9 Bed knife cover plate Bed knife cover plate left Bed knife cover plate right Cover plate mounting screw DIN912 – M12x35 – 12.
107 108 109 1 1 1 200 201 202 203 204 205 206 1 6 6 6 2 2 207 208 2 2 200 201 202 203 203 204 205 1 6 6 6 1 2 300 301 302 303 304 305 306 307 308 309 2 2 2 1 1 3 2 2 24 Screen complete (Standard) Screen 12/16/20/25 Screen support screw DIN912–M12x35–8.8 Washer DIN125-B-13-140HV Spring washer DIN127-A-13 Clamp Clamp mounting screws DIN933 – M20 – 8.8 Washer DIN125-A – 20 – 140HV Spring washer DIN127-A-20 Screen complete (Hydraulic) Screen Screen support screws DIN912-M12x35-8.
BJ5-615 416 417 418 419 1 1 1 6 Torque arm screw Cover plate Cover 75KW Rubber bushing plate screws DIN933-M16x50-12.
2 803 804 805 806 1 1 1 Piping Connectors Hydraulic unit 5.6kW Set of sealing for cylinder Oil filter 12AT-10-CR 900 901 902 903 904 905 2 1 1 2 2 Electrical parts Safety switch AZ15ZVRK-1476-1 Small control box Control panel Proximity switch II0297 Cable for proximity switch EI0200 SMS 2000 Pos.
BJ5-615 403 2 404 405 2 8 406 2 407 2 408 409 410 411 412 413 414 415 416 417 418 419 2 2 2 2 2 2 2 2 2 2 2 12 420 421 422 423 12 12 12 2 500 501 502 1 144 144 503 504 505 144 144 288 600 601 602 603 2 14 28 14 604 14 605 28 606 607 1 1 5 28 700 701 702 703 1 2 2 8 704 705 2 1 Gear pulley taper bushing TB 3535-50 Gear pulley taper bushing TB 3535-55 Key C25x210 V-Belt SPC 2430 V-Belt SPC 2550 Motor pulley SPC 250-4 Motor pulley SPC 300-4 Motor pulley taper bushing 3535-65 Motor
706 12 707 708 709 710 711 712 12 12 12 12 1 4 713 714 715 716 1 2 2 8 717 4 800 801 802 803 804 805 806 900 901 902 903 904 905 Mounting screws ram arm DIN912-M16x9012.9 Nut DIN934-M16-10 Washer DIN 433-16-300HV Spring washer DIN127-A-16 Mounting pin DIN94-2.5x32 Scraper Spring for scraper YI GB1356-78 n=14/d=2/D=12/H=50 Cover plate for scraper Upper cylinder screw Lower screw for cylinder mounting Mounting screw for cylinder screw DIN912 – M16x25 – 12.
SMS 850 Hydraulic Screen Spare Parts Pos 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Description Oil filter net Oil filter net Electric motor Wheel pump Vane pump Check valve Check valve Spillover valve Sequence valve Pressure Gauge Solenoid valve Pilot operated check valve Throttle check valve Pressure relay Oil gauge Oil lubricator Scavenge oil filter Oil box Solenoid valve Throttle check valve Standard MF-06 MF-08 5HPX4P(straight system) 380V HGP-2A-F6R 50T-19 CIT-03, CIT-04 CRG-03 BSG-03-INP-2
10 11 11-1 12 12-1 13 14 15 16 17 18 19 20 21 22 Pressure Gauge Solenoid valve Solenoid valve Pilot operated check valve Pilot operated check valve Throttle check valve Pressure relay Oil gauge Oil lubricator Scavenge oil filter Oil box Check valve Throttle check valve Pressure gauge switch Pressure Gauge LA-250(including connector) DSD-G03-6C-***-31 DSD-G02-6C-***-31 MPD-03-W-1-10 MPD-02-W-1-10 PT-04 PS-02-3-10 LS-3 AB-1162 70134-10C-R 90L CIT-04 PT-03 GCT-02 LA-100(including connector) A-5 Technical A
Sterling, Inc. 2900 S. 160th Street New Berlin, WI 53151 www.sterlco.
