SXS Extreme Duty Shredder SXS 1500 & 2000 Part Number: EXS-0003-S Bulletin Number: BJ5-620 Effective: 9.30.2008 Write Down Your Serial Numbers Here For Future Reference: _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ We are committed to a continuing program of product improvement. Specifications, appearance, and dimensions described in this manual are subject to change without notice. DCN No.
Shipping Info Unpacking and Inspection You should inspect your equipment for possible shipping damage. Thoroughly check the equipment for any damage that might have occurred in transit, such as broken or loose wiring and components, loose hardware and mounting screws, etc. In the Event of Shipping Damage According to the contract terms and conditions of the Carrier, the responsibility of the Shipper ends at the time and place of shipment.
Storage, Disposal, Transportation Storage Clean the machine (see Cleaning the Machine). Preserve all polished metal surfaces using a suitable rust preventing agent. Store the machine in an dry and enclosed space. Cover the machine completely with a plastic sheet. Disposal The disposal of machines, machine components, and process materials is partially subject to legal controls. More detailed information is given at the relevant administrative authority (i.e.
Table of Contents CHAPTER 1: SAFETY................................................................ 5 1-1 1-2 1-3 1-4 How to Use This Manual ............................................................................................. 5 Safety Symbols Used in this Manual .....................................................................5 General Safety Regulations ........................................................................................ 6 Responsibility ...................................
Chapter 1: Safety 1-1 How to Use This Manual Use this manual as a guide and reference for installing, operating, and maintaining your equipment. The purpose is to assist you in applying efficient, proven techniques that enhance equipment productivity. This manual covers only light corrective maintenance. No other maintenance should be undertaken without first contacting a service engineer. The Functional Description section outlines models covered, standard features, and safety features.
1-2 General Safety Regulations This machine uses knives for the performance of its intended use. Consequently, it can be a dangerous machine to operate and maintain unless these safety regulations are followed. These regulations should be read, understood and periodically reviewed by all personnel involved in any way with this machine. Never operate or remove any machine components that are secured by wrench-type fasteners unless the motor is electrically locked out and the rotor is motionless.
1-4 Warnings and Precautions Our granulators are designed to provide safe and reliable operation when installed and operated within design specifications, following national and local safety codes. To avoid possible personal injury or equipment damage when installing, operating, or maintaining this granulator, use good judgment and follow these safe practices: ; LEARN AND OBEY your company’s safety policy regarding granulating equipment.
; ROTATION OF MOTORS: The correct rotating direction for the machine motor is clearly marked on the machine. Always check for proper rotation of motors. Incorrect rotation direction can cause severe damage. ; ELECTRICAL GROUNDING: All electrical equipment on the granulator must be grounded in accordance to all local codes and Article 250 of the National Electric Code. ; ALWAYS DISCONNECT AND LOCKOUT the main electrical power to the granulator before performing any service.
Type of Danger Activity Possible Consequences Preventative Measures Pulling in caused by running V-belts All activities Serious injury can result from hair, jewelry, etc. being pulled into the machine. • Never dismount V-belt protection and window. Direct/indirect contact with live parts in terminal box. Maintenance work, start up Serious injury or death • Only trained electricians may carry out all work on the electrical equipment.
Type of Danger Activity Possible Consequences Preventative Measures Crushing, cutting, amputation caused by manipulation of protective devices All activities Serious injury or death • Never make the protective devices ineffective. • Check the protective devices regularly for proper function according to the manual’s specifications.
Chapter 2: Functional Description 2-1 Models Covered in This Manual The models included in this manual are the Sterling SXS 1500 and 2000 Extreme Duty Shredders. The SXS Extreme Duty Shredders are designed for processing plastic waste for reclamation and recycling, large extruder purgings, large reject parts, trip scraps, baled or loose film, synthetic fiber, wood processing scrap, medical waste, cardboard, paper, and carpet.
Machine (Standard Execution) (1) (2) (3) (4) (5) (6) (7) (8) Base Frame Machine door Hopper door Gear Box Drive motor V-belt guards Ram hydraulic guards Discharge area 3 7 4 2 6 5 8 1 The machine housing, drive motor, gear box, hydraulic system and terminal box are mounted on the base frame for electrical connections.
In-feed Hopper The material in-feed flows through an in-feed hopper made to ensure the material is delivered safely and correctly. NOTE: An optional top-hinged cover to prevent in-feed material fly-back during size reduction is available. Special hopper with hydraulic cover Additional In-feed Device If the machine has an optional in-feed device, such as a conveyor belt, please refer to the additional information about the accessory in the manufacturer’s manual that accompanied the accessory.
Drive The drive of the rotor runs using an electric motor via V-belts. The motor (mounted on sliding rails or a motor plate) can be adjusted for regulating the tension of the V-belts by using tensioning screws. The V-belt pulley is attached to the motor shaft with a special tensioning element.
1 3 (1) Rotor cutter (2) Screen support (hydraulic) (3) Bed knife 2 (1) Rotor cutter (2) Screen support 1 2 The rotor is accessible after opening the machine door and removing the screen. The rotor is arranged on roller bearings that are situated outside the housing. The V-belt pulley is attached to the rotor axis with a taper brush. The rotor is dynamically counter balanced and has vibration-free concentricity.
An optional feature is a water cooling system for the rotor used for special applications. Bearing with water plug for rotor cooling Screen and screen support The screen and the screen support are welded together and fixed to the housing by screws in standard execution. The screen is slightly larger in radius than the cutting circle of the rotor cutters. The screen perforation is selected according to the desired grain size of the shredded material.
(1) Hydraulic cylinder (2) Screen support (3) Screen 3 1 2 Discharge of Shredded Material Normally the shredded material will be discharged onto a conveyor belt. (Options include a discharge with blower or with a screw conveyor.
Hydraulic Ram The hydraulic ram is fixed on two arms arranged on flange bearings. Two heavy duty hydraulic cylinders move the ram back and forth. The ram moves automatically after switching on the hydraulic system and the shredder when the machine is operated in automatic mode. NOTE: The ram can be moved by hand on the control panel when run in manual mode.
2-4 Safety Features Protective Devices CAUTION! The Machine may under no circumstances be operated without these protective devices. The use of faulty or manipulated protective devices is strongly prohibited. Safety Device for Machine and Hopper Doors Safety device: machine door Safety device: hopper door The shredder can only be operated if the doors are closed deactivating the safety switch. The safety contact is broken when the machine or hopper door is open, thus switching off the machine.
V-Belts and Ram Guards V-belt and ram guards are bolted to the machine. They can be dismounted for installation and maintenance work when all rotating parts have come to a complete standstill and the machine is electronically locked out. 1 (1) Ram guarding 2 (2) V-belt guarding NOTE: The operator must fit and mount the protective devices delivered with the machine according to the current legal safety regulations if the machine is delivered without drive motors upon customer request.
The following protective gear must be worn when performing the outlined tasks: Unloading machine. Connecting machine. Operation. Cleaning. Maintenance of bearings. Screen replacement. Maintenance of V-belts. Maintenance of cutting knives. Knife sharpening. Safety helmet x Safety boots x x x x x x x x Safety gloves x x Safety goggles x x Ear muffs x x x x x x x x Emergency Stop Button The machine may only be operated with the installed Emergency Stop buttons.
Chapter 3: Installation 3-1 Uncrating the Equipment Requirements at Application Site Check the application site to make sure it conforms to the qualifications listed below. • • • • • • • • • • The site has enclosed space. The ground has sufficient load-bearing capacity (refer to the “Technical Specifications” in the Appendix for machine weight). The unevenness of the ground surface may not exceed 5 mm. The machine must be freely accessible from all sides.
WARNING! SUSPENDED LOAD! • Falling loads can cause serious injury or death. • Only use a crane or forklift suitable for the weight and the dimensions of the load. • Use suitable stopping equipment and pay attention to the gravity center location. • DO NOT step under the suspended load. • Wear a safety helmet in addition to basic protective gear. WARNING! OVERTURNING OR FALLING MACHINE! • Serious injury or death can result.
WARNING! Use caution when operating specific equipment to prevent electrical shock. Installation, service, alterations, and/or modifications must only be done by qualified personnel and with high regard for safety. Not conforming to the requirements could result in bodily harm, death, or costly damage. NOTE: Alterations to the wiring diagrams require approval. Failure to do this will exclude all guarantee claims. The wiring schematics are located in the control panel.
Checking the Rotational Direction Rotational direction of the motors must be checked before initial start-up. The following steps must be completed. 1. Switch the machine ON and then immediately OFF again. 2. Observe whether the discharge air fan in the drive motor is rotating in the direction of the direction arrow. NOTE: If running in the wrong direction, reconnect the motor connection immediately. Damage to the machine will result from operation in the wrong direction.
9 Switch ON machine for a short period of time and check rotational direction. The rotational direction can be seen at the discharge air fan of the drive motor (observe running direction arrow). 9 Switch ON hydraulic unit for a short time and check rotational direction. 9 Allow machine to run for approximately 10 minutes without shredding material. 9 Connect material discharge device and in-feed device; check rotational direction drives. 9 Feed grinding material uniformly.
Chapter 4: Operation 4-1 Start-up WARNING! No persons should operate the machine until they have read and understand all parts of the operation manual. Machine Check—Before Switching Machine ON 9 Cutters and bed knives are properly set and the screws are tightened with the specified torque. 9 Screen is inserted into the screen support according to the instructions, and the screen support is fixed at the end position with tightened mounting screws. 9 The cutting chamber is free of foreign matter.
• Throw the material into the in-feed hopper. • The machine should be fed from the front. • If your machine has an additional in-feed device installed, please observe the additional information for working with the in-feed device. DANGER! Do not climb into the in-feed hopper while operating the machine. Death will result. Emptying the Screen 1. Switch off the shredder at the main switch. 2. Safeguard main switch using a padlock. 3. Open the machine door. 4. Safeguard machine door. 5.
Hydraulic Set-up 1. Connect hydraulic pipes to the machine—make sure the upper hydraulic pipe is connected to the upper pipe at the machine. 2. Connect the wires for the motor and magnetic valves. 3. Fill the oil tank with hydraulic oil No. 46 or No. 32 until the maximum is reached and mark the level indicated by the gauge. 4.
SQ3 工进 杆径?63 SQ4 SQ1 SQ2 Figure: Hydraulic Set-up 缸径?125 ( 初始设定压力 15MPa) ( 初始设定压力 9MPa) 12ml / r ec BJ5-620 ( 初始设定压力 9MPa) 33ml / r ec Operation 30 of 73
4-3 Shut-down Switch OFF Machine 1. Switch OFF the material in-feed device (accessories). 2. Wait until the remaining material has been shredded, and then switch OFF the shredder (main switch to 0). 3. Switch OFF the material discharge device.
Chapter 5: Maintenance 5-1 Preventative Maintenance Schedule Only trained and specialized personnel should carry out maintenance work. Maintenance Plan WARNING! • Danger caused by electrical voltage and starting the machine during maintenance work. Death can result! • ALWAYS turn main switch to 0, safeguard using a padlock, and attach a warning sign while carrying out maintenance work. The tasks for maintenance work are described below.
5-2 Preventative and Corrective Maintenance Checking the Protective Devices Check the safety devices for: • Stipulated condition • Stipulated location • Safe mounting • Stipulated function WARNING! Danger due to non-functioning protective devices can cause serious injury or death! • Eliminate all defects before operating the machine! • If defects occur during operation, stop the machine immediately and eliminate the defects! • Do NOT change or remove any protective devices.
9. Remove clinging shredded material residue using a suitable wooden scraper. 10. Place the screen back into its working position and fasten with the mounting screws. 11. Close the machine and hopper doors. 12. Machine can be started again. Replacing the Gear Box The gearbox is designed so a replacement is only necessary in exceptional cases. Dismounting and mounting of the gear box requires specialist knowledge and a careful working method.
Mounting the Rotor 1. Before starting, clean the bearing seat surfaces and check the key. 2. Lift the rotor using suitable lifting and stopping equipment and place carefully into the bearing seats. 3. Attach the bearing housing (Pos.) to the bearing seats using screws. 4. Put the gear onto the rotor axis. 5. Put back the rotor mounting slot cover plates. 6. Put in the screen. 7. Pull on V-belts and adjust the V-belt tension force. 8. Attach the V-belt. 9. Carry out a test run.
10. Carefully lift out the complete rotor using suitable lifting and stopping equipment. 11. Lay the rotor down in a safe location. Suitable for this are timber beams of appropriate size. 12. Loosen the mounting screws on the bearings cover. 13. Pull the bearing housing off using a pulling-off device. 14. Pull the bearing off the rotor axis using a pulling-off device. Mounting the Main Bearings 1. Before mounting, clean the bearing surfaces and the shaft surfaces thoroughly and grease lightly. 2.
Lubrication Intervals Shift Operation Replace Lubricant Check One shift operation Every 18 months Monthly Two shift operation Every 9 months Monthly Three shift operation Every 6 months Monthly Check lubricant quality You can judge whether the lubricant needs to be replaced by checking for the following features: • Change in consistency • Discoloration • Degree of soiling Replacing or Refilling Lubricant BJ5-620 • Fill the bearings uniformly with grease until all operating surfaces are
Refilling lubricant The grease reaches through the circulating grooves and bores via lubrication nipples into the interior of the bearing. The greasing quantity is .13 to .22 lbs (60 to 100 g) roller bearing grease F3 per bearing. Grease Nipple Replacing Lubricant Renewing the lubricant between intervals is only necessary when there unusual noises or overheating.
List of Recommended Lubricants Country of Manufacturer/Manufacturer Roller Bearing Grease ARAL ARL Grease HL 3 BP BP ENERGREASE LS 3 CASTROL CASTROL SPHEEROL AP 3 ESSO Beacon 3 FUCHS FUCHS Grease 1200 FUCHS Grease FWA 220 SHELL SHELL Alvania Grease 3 MOBIL-OIL MOBILUX 3 WISURA WISURA Liba L 3 Zeller $ Gmelin ZET GE Grease M 50 FAG FAG L 71 ANTAR ROLEXA Holland, Beverol Beverol Multi Purpose Grease Italy, Agip AGIP Grease 33 FD Swede, NYNAS Nynas FI 3-42 BJ5-620 Maintenance 39
Mounting and Dismounting TAPER-LOCK Tensioning Element The motor and the gear V-belt pulleys are attached to the shaft using a TAPER-LOCK tensioning element. The disks must be dismounted for certain maintenance processes.
Tightening Torque of the Screws Refer to the table below.
8. Pivot the screen support into the working position and fasten using mounting screws. 9. Close the machine door. 10. Shredder can be started again. (Please refer to image from “Emptying the Screen”.) V-Belts V-belts are wearing parts that stretch and must be re-tensioned. Regular checks on the tension force of the V-belts and the condition of the V-belts are necessary in order to guarantee a long service life of the V-belts. Checking the tension force of the V-belt 1. Remove the V-belt cover. 2.
a: Distance between roller centers. b: Sag F: Force (direction) Re-tensioning and relaxing the V-belt Enlarging or decreasing the centre distance “A” tensions or relaxes the V-belt. 1. Loosen the tensioning screw. 2. Shift the drive motor as required onto the sliding rails. 3. Lock the drive motor into new position using tensioning screws so that the motor shaft is parallel to the rotor axis and aligned. 4. Check the tension force of the V-belt (see “Checking the Tension Force of the V-belt”). 5.
Working on the Cutting Knives Correctly setting and mounting the cutting knives is important when working with shredders to ensure efficient and economic function. Replacing and Checking the Cutting Knife Mountings Certain machine parts are subject to stress during operation as a result of vibrations that can lead to loosening of the screw connections. It is absolutely necessary to check the cutter and bed knife mounting screws in accordance with the maintenance plan. 1.
Dismounting the Cutters 1. Switch OFF the shredder at the main switch. 2. Safeguard main switch using a padlock. 3. Open the machine door. 4. Safeguard the machine door. 5. Remove screen. NOTE: Although it is possible to reach the cutting shaft by climbing into the feeding chamber, it is recommended to access the cutters through the machine door located at the front of the machine. The shaft can be rotated manually by turning the motor v-belt pulley. 6.
6. Clean the hexagon head socket of the cutter mounting screw (2). 7. Loosen the bolt using a high quality Allen key (10 mm). If necessary knock the Allen key lightly with a hammer to loosen it. 8. Take out the cutter mounting screw, the washer and the cutter. 9. Clean the hexagon head socket of the knife holder fixing bolts (4). 10. Loose the bolt using a high quality Allen key (6 mm). Knock the Allen key lightly with a hammer to loose it if necessary. 11. Take out the cutter holder mounting screws (4).
5. Clean the hexagon head socket of the knife mounting bolts (2) and the cover plates mounting bolts. 6. Loosen the cover plate mounting bolts using a high quality Allen key (10 mm). Knock the Allen key lightly with a hammer to loosen if necessary. 7. Take out the bolts and cover plates. 8. Loosen the knife adjusting screws for pulling and take them out. 9. Loosen the knife mounting bolts with Allen key (10 mm). Use a hammer to lightly knock key if necessary. 10. Take out the knife mounting bolt and knife.
3. Put in the cutter holder mounting bolts (DIN912 – M10x30 – 12.9) and put some Loctite on them. 4. Make sure that the cutter holder fits properly. 5. Tighten the cutter mounting bolts using a torque wrench. NOTE: The required torque for the cutter holder mounting bolts is 83 Nm (also see the table under “Replacing and checking the cutting knife mountings”). WARNING! Danger of cutting caused by sharp knives at all times—even when rotor is at standstill.
Mounting the Bed Knives 1. Clean the knife supporting surface and the holes on the knife holder 2. Insert sharp knife or turn old knife. 3. Put in the knife adjusting bolts and adjust them roughly 4. Put in the knife mounting bolts (DIN912 – M16x60 – 12.9) and tighten lightly first 5. Adjust the gap between cutter and bed knife to 0.8-1.0 mm 6. Tighten the knife mounting bolts using a torque wrench.
Sharpening Cutters and Bed Knives Shredder cutters have 4 cutting edges. This means they can be turned 3 times. The cutters should be replaced after the third use. Bed knives can be turned 2 times and can be re-sharpened as long as you can fix them with the long hole. 1. Dismount the cutters and bed knives (see “dismounting the cutters”). 2. Sharpen the cutters and bed knives.
(1) Bed knife (2) Knife mounting screws (3) Knife holder (4) Cover plates (5) Knife adjusting screw for pushing (6) Knife adjusting screw for pulling (7) Cover plate mounting screws 6 5 2 3 4 1 7 1. Remove old knives (see “Dismounting the bed knives”). 2. Insert sharp knife or turn old knife. 3. Put in the knife adjusting bolts and adjust them roughly 4. Put in the knife mounting bolts and tighten lightly first 5. Adjust the gap between cutters and bed knife to 0.8-1.0 mm using a calibre gauge. 6.
Transporting and Storing the Cutting Knives WARNING! • • • • • Danger of cutting caused by sharp knives. Serious injury, in particular to hands and fingers, can result. Wear protective gloves. Only transport and store the packaged cutting knives. Grease the cutting knives well so they do not rust. Protect the cutting edges with doubled cardboard and use adhesive tape to safeguard the knives against slipping out of the sides of the sheath.
Hydraulic liquid recommendation Designation to DIN 51 524 HLP 32 Ambient temperature: -7 to +70°C Supplier Name of the oil ARAL Aral Vitam GF 32 Aral Vitam HF 32 BP Energol HLP-D 32 BP Energol HLP 32 BP Energol SHF 32 Elfolna 32 Hydrelf 32 Nuto H 32 HLPD-Oel 32 Fina Hydran 32 Renolin MR 10 Renolin B 10 Mobil DTE 24 Mobil DTE 17 Drucköl HLP 32 - C Hydrauliköl HLPD 32 Rando Oil HD A - 32 Rando Oil HD AZ - 32 Alcor Oil DD 32 BP ELF ESSO FINA FUCHS MOBIL TEXACO BJ5-620 Maintenance 53 of 73
Chapter 6: Troubleshooting 6-1 Introduction The utmost in safety precautions should be observed at all times when working on or around the machine and the electrical components. All normal troubleshooting must be accomplished with the power off, line fuses removed, and with the machine tagged as out of service. The use of good quality test equipment cannot be over-emphasized when troubleshooting is indicated.
Problem Machine blocks or switches itself off Possible Cause Possible Remedy Too much feed material. Reduce grinding material infeed. Screen blocked. Clean screen, check condition, select larger screen perforation if necessary. V-belts slip. Check V-belt tension and condition. Re-tighten or replace if necessary. Knife condition. Check knives and resharpen or replace if necessary. Cutting gap. Check cutting gap and set following the instructions in this manual. Discharge blocked.
Problem Overheating of the shredded material. Unusual vibrations. Possible Cause Possible Remedy View first 5 possible causes for “Machine blocks or switches itself off” View first 5 possible remedies of “Machine blocks or switches itself off” Screen perforation too small. Insert a screen with larger perforation. Knives wrongly sharpened. Modify knife finish only after consulting the service department. Material rubs against the housing wall. Fit anti-winding device. Insufficient cooling.
Problem Cutting gap alters during operation. Screen damage. Shredder does not start. Shredder blocks when under load. Possible Cause Possible Remedy Knife mounting screws not tight. Re-tighten using torque wrench following the instructions in this manual. Screw fatigue. Fit new screws. Washers deformed. Insert new washers. Knife holder surface deformed. Insert new knife holders. Supporting surfaces not clean. Clean and re-dust supporting surfaces. Threads in housing worn.
Hydraulic Troubleshooting Problem Motor doesn’t work. Oil pump doesn’t work. Oil pump noise Possible Cause Possible Remedy Electric source. Correct wire connection. Motor damage. Replace motor. Motor not functioning. Correct wire connection. Pump damage. Replace pump. Filter jam. Clean the filter. Hydraulic oil is too thick. Change hydraulic oil. Hydraulic oil has bad quality. Change hydraulic oil. Pipe is leaking. Tighten pipe connectors. Pump damage. Change pump.
Appendix A-1 Returned Material Policy Credit Returns Prior to the return of any material, authorization must be given by the manufacturer. A RMA number will be assigned for the equipment to be returned. Reason for requesting the return must be given. All returned material purchased from the manufacturer is subject to 15% (75.00 minimum) restocking charge. All returns are to be shipped prepaid. The invoice number and ate or purchase order number and ate must supplied.
A-2 Technical Specifications BJ5-620 Appendix 60 of 73
A-3 Drawings and Diagrams NOTE: Please refer to the corresponding spare parts lists in the following section.
Bed knife fixing BJ5-620 Appendix 62 of 73
Rotor Assembly BJ5-620 Appendix 63 of 73
Drive BJ5-620 Appendix 64 of 73
Ram BJ5-620 Appendix 65 of 73
Ram scraper BJ5-620 Appendix 66 of 73
SQ3 工进 杆径?63 SQ4 SQ1 SQ2 SXS 1500/2000 Standard Hydraulic Diagram 缸径?125 ( 初始设定压力 15MPa) ( 初始设定压力 9MPa) ( 初始设定压力 9MPa) 33ml / r ec 12ml / r ec BJ5-620 Appendix 67 of 73
A-4 Spare Parts List SXS 1500 Pos. 100 101 102 103 104 105 106 107 108 109 1 2 1 1 1 2 1 1 1 Description/Standard Machine complete Standard hopper PP-scraper side PP-scraper top Upper door Lower door Safety grid side Safety grid back Safety grid back Ram residual chute 200 201 202 203 204 205 206 207 1 6 2 1 2 4 4 Screen complete (Hydraulic) Screen Screen support screws DIN912 – M16x25 – 8.
413 414 415 416 417 418 419 2 2 2 2 2 2 12 420 421 422 423 12 12 12 2 Rubber bush plate Rubber bush Ø116x68x100 Copper bush ø68x63x100 Torque arm bolt Washer disc Rotor cover Rubber bush plate bolts DIN933 – M20x65 – 12.9 Washer DIN433 – 20 Spring washer DIN127 – A – 20 Nut DIN934 – M20 – 10 Torque arm complete 75kW 500 501 502 503 504 505 1 76 76 76 76 152 E-knife rotor ø660x1500 Rotor knife 60x60x30 Rotor knife Mounting Bolt DIN 912 - M16x50 - 12.
806 1 Oil filter SP-10 900 901 902 903 904 905 2 1 1 2 2 Electrical parts Safety switch CAZ15zvrk Small control box Control panel Proximity switch II0297 Cable for Proximity switch E10200 SXS 2000 Pos.
BJ5-620 406 2 407 2 408 409 410 411 412 413 414 415 416 417 418 419 2 2 2 2 2 2 2 2 2 2 2 12 420 421 422 423 12 12 12 2 V-Belt SPC3250 Motor pulley SPC315-5 Motor pulley SPC335-6 Motor pulley taper bush TB 3535-75 Motor pulley taper bush TB 4040-75 Key Motor shaft Pulley cover + support Base frame for motor Gear box SEW MC3PLHF07-SD i=23 Torque arm plate Rubber bush plate Rubber bush Ø116x68x100 Copper bush ø68x63x100 Torque arm bolt Washer disc Rotor cover Rubber bush plate bolts DIN933 – M20x65 –
716 8 717 4 800 801 802 803 804 805 806 900 901 902 903 904 905 Fixing bolt for cylinder bolt DIN912 – M16x45 – 12.
A-5 Technical Assistance Parts Department Call toll-free 7am–5pm CST [800] 423-3183 or call [262] 641-8610, Fax [262] 641-8653 The ACS Customer Service Group will provide your company with genuine OEM quality parts manufactured to engineering design specifications, which will maximize your equipment’s performance and efficiency. To assist in expediting your phone or fax order, please have the model and serial number of your unit when you contact us.
