Submittal Sheet

ManualsBrandsStiebel Eltron ManualsIndirect Water HeatersSBB 600 Plus 163 Gallon DHW Indirect Water Heater Tank

17 West St., W. Hatﬁeld, MA 01088 | 800.582.8423 | 413.247.3380 | fax 413.247.3369 | info

stiebel-eltron-usa.com | www.stiebel-eltron-usa.com

rev. 1.2021 | Due to our continuous process of engineering and technological advancement, speciﬁcations may change without notice.

1 Sacrificial anode indicator

2 Thermometer

3 Well for temperature sensor (boiler)

4 Well for temperature sensor (solar)

5 Clean-out port

6 Foam insulation

7 Cold water inlet

8 Heat exchanger ports

lower loop (solar)

9 Lower exchanger coil (solar)

10 Heat exchanger ports

upper loop (boiler)

11 Upper exchanger coil (boiler)

12 Hot water outlet

Dimensions

Warranty

Left to right:

SBB 300

SBB 400

SBB 600 Plus

Subject to the terms and conditions set forth in this limited

lifetime warranty, Stiebel Eltron, Inc. (the “Manufacturer”)

hereby warrants to the original purchaser (the “Owner”) that

each storage tank (the “Tank”) shall be free from defects in the

Manufacturer’s materials or workmanship for a period of:

1. (10 Years) from the date of purchase for single, two-, and

three-family residential installations

2. (5 Years) from the date of purchase for all other

installations

3. (Excluded) sacriﬁcial or electronic anode

As Owner’s sole and exclusive remedy for the above warranty,

Manufacturer shall, at the Manufacturer’s discretion, either

factory repair or replace the defective Tank with a replacement

unit or part(s) with comparable operating features.

Manufacturer’s maximum liability under all circumstances shall

be limited to the Owner’s purchase price for the Tank.

This limited warranty shall be the exclusive warranty made by

the Manufacturer and is made in lieu of all other warranties,

express or implied, whether written or oral, including, but

not limited to warranties of merchantability and ﬁtness for

a particular purpose. Manufacturer shall not be liable for

incidental, consequential or contingent damages or expenses

arising directly or indirectly from any defect in the Tank or the

use of the Tank. Manufacturer shall not be liable for any water

damage or other damage to property of Owner arising, directly

or indirectly, from any defect in the Tank or the use of the Tank.

Manufacturer alone is authorized to make all warranties on

Manufacturer’s behalf and no statement, warranty or guarantee

made by any other party shall be binding on Manufacturer.

Manufacturer shall not be liable for any damage whatsoever

relating to or caused by:

1. any misuse or neglect of the Tank, any accident to the Tank,

any alteration of the Tank, or any other unintended use;

2. acts of God and circumstances over which Manufacturer

has no control;

3. installation of the Tank other than as directed by

Manufacturer and other than in accordance with

applicable building codes;

4. improper installation and/or improper materials used

by any installer and not relating to defects in parts or

workmanship of Manufacturer;

5. failure to maintain the Tank or to operate the Tank in

accordance with the Manufacturer’s speciﬁcations;

6. failed components not originally installed by the

Manufacturer as a part of the unit at the time of sale;

7. exposure to freezing conditions;

8. exposure to harmful chemicals, contaminated water,

corrosive ﬂuids or atmosphere, liquids harmful to steel

tubing including improperly applied or maintained heat

transfer ﬂuids.

Type SBB 300 Plus SBB 400 Plus SBB 600 Plus

A Height of unit w/insulation 66.1˝ (1679 mm) 72.7˝ (1848 mm) 68.3˝ (1735 mm)

B Height of unit without insulation 63.3˝ (1609 mm) 70.1˝ (1781 mm) 65.7˝ (1670 mm)

C Height of well for temp. sensor 46.4˝ (1179 mm mm) 48.7˝ (1238 mm) 46.9˝ (1192 mm)

D Height thermometer 41.1˝ (1045 mm) 43.0˝ (1093 mm) 41.5˝ (1055 mm)

E Height spare port 40.3˝ (1025 mm) 42.4˝ (1078 mm) 40.9˝ (1040 mm)

F Height of well for temp. sensor 21.9˝ (557 mm) 22.0˝ (560 mm) 23.4˝ (595 mm)

G Height inspection flange 14.4˝ (365 mm) 14.4˝ (367 mm) 15.9˝ (405 mm)

H Height cold water feed 2.9˝ (73 mm) 2.6˝ (65 mm) 2.0˝ (50 mm)

I Height solar cold feed 11.0˝ (280 mm) 11.1˝ (282 mm) 10.9˝ (277 mm)

J Height solar hot return 34.0˝ (865 mm) 34.1˝ (867 mm) 33.9˝ (862 mm)

K Height heater hot boiler return 38.4˝ (975 mm) 44.5˝ (1130 mm) 42.9˝ (1089 mm)

L Height circulation port 52.7˝ (1339 mm) 63.0˝ (1600 mm) 57.2˝ (1453 mm)

M Height cold boiler feed 52.7˝ (1339 mm) 63.0˝ (1600 mm) 57.2˝ (1453 mm)

N Overall height 67.08˝ (1704 mm) 73.74˝ (1873 mm) 69.29˝ (1760 mm)

O Width without thermal insulation 21.65˝ (550 mm) 23.62˝ (600 mm) 29.52˝ (750 mm)

P Width with thermal insulation 27.55˝ (700 mm) 29.52˝ (750 mm) 36.22˝ (920 mm)