STIHL FEILGERAT FGl FILING UNIT FG 1 AFFUTEUR A LIIVIE FG 1 APARATD LIIVIADDR FG 1 8.
english Printing inks contain vegetable oils; paper can be recycled. Contents Guide to Using this Manual ............ Safety Precautions ......................... Application ...................................... Clamping the Guide Bar ................. Mounting the Filing Tool on the Guide Bar ............................ Selecting and Fitting File ................ Setting Up ....................................... Sharpening ..................................... Quality Certification .................
english Guide to Using this Manual Pictograms All the pictograms attached to the machine are shown and explained in the this manual. The operating and handling instructions are supported by illustrations. In addition to the operating instructions, this manual may contain paragraphs that require your special attention. Such paragraphs are marked with the symbols described below: Symbols in text Warning where there is a risk of an accident or personal injury or serious damage to property.
english Safety Precautions To reduce the risk of personal injury, special safety precautions must be observed while operating the filing tool. Read the operating instructions carefully and keep them in a safe place for later reference. Always shut off the saw engine before working with the filing tool: Move Master Control lever / slide control or the separate stop switch to STOP or $. Electric saws: Disconnect plug from power supply. Wear gloves.
english Mounting the Filing Tool on the Guide Bar Clamping the Guide Bar Clamping the guide bar Depending on the position of the master cutter Pointing to right Pointing to left Use a slide caliper to find the shortest cutter and mark it, with chalk. : Place the filing tool on the guide bar. : The clamping jaws (1) must point towards the bar nose and be in line with top edge of the rivet heads. : Tighten down the wing screw (2).
english Selecting and Fitting File Setting Up Use only special saw chain sharpening files. Other files have the wrong shape and cut and are unsuitable for sharpening saw chain. Adjusting filing angle : Use the adjusting screw (3) to center the filing tool above the chain. : Tighten the second clamping jaw with the clamp screw (4) so that the chain can still be pulled along the bar with a screwdriver engaged in a cutter. FG 1 Round file Ø mm inch 4.0 5/32 4.0 5/32 4.0 5/32 4.8 3/16 5.2 13/64 5.
35 0 2 45 : 25 565BA024 KN english To rotate guide, lift it clear of the teeth. 45 35 0 25 1 565BA004 KN 565BA007 KN 2 : Set the filing angle (2), e.g. 30° and tighten down the knurled nut. 3 : 18 : Position the round file (1) between the side plate and depth gauge of the master cutter by swinging and lifting the filing frame. 565BA006 KN 1 Aligning the filing frame Position the master cutter (3) below the center of the knurled nut (1).
english 3 4 5 Turn the acorn nut (2) to set filing frame at a right angle to the clamping jaws. 565BA009 KN 1/10 ø 565BA020 KN : 565BA027 KN 90° 565BA008 KN 2 : FG 1 Turn the adjusting screw (3) (counterclockwise to lower file – clockwise to raise file) until about 1/10 of file diameter projects above the top plate. : Loosen the knurled nut (4). : Move the stop (5) up against the back of the cutter to be sharpened (master cutter) and tighten down the knurled nut.
english Sharpening Use the setting for the master cutter to sharpen all the other cutters in the row. 6 2 1 2 565BA012 KN 3 : Turn the acorn nut (2) slowly clockwise until the distance between it and the stop bar (6) is about 0.1 to 0.2 mm. 1 565BA021 KN 6 2 565BA010 KN 2 During the sharpening process make sure the stop (3) always locates properly against the back of the cutter being sharpened.
english Depth gauges : : Tighten down the knurled nut. : Turn the guide bar through 180° and clamp it in the bech vise or STIHL bar vise (special accessory). : Swing the filing frame down. : Position the round file between the side plate and depth gauge of the first cutter in the second row. : Sharpen the first cutter in the second row. : Check the cutter length (A). 2 : : FG 1 Filing gauge Part No.
english 45 : Set the filing angle on the guide to 0°. : Pull chain along the bar until the depth gauge is under the file. : : Lubricate the guide with oil. Impregnate the felt in the guide to ensure free movement of the filing frame. Rotate the file at regular intervals while filing to avoid one-sided wear. Fit the flat file (2) (special accessory) in place of the round file. : Adjust thestop (3) so that the file does not touch the cuting edge.
english 000BA026 Quality Certification All STIHL products comply with the highest quality standards. An independent organization has certified that all products manufactured by STIHL meet the strict requirements of the ISO 9001 standard for quality management systems in terms of product development, materials purchasing, production, assembly, documentation and customer service.
english 24 FG 1
