Instruction Manual
Table Of Contents
- STIHL FS 91, 91 R
- 1 Guide to Using this Manual
- 2 Safety Precautions and Working Techniques
- 2.1 Clothing and equipment
- 2.2 Transporting the machine
- 2.3 Refueling
- 2.4 Before starting
- 2.5 Starting the engine
- 2.6 Holding and guiding the machine
- 2.7 While working
- 2.8 Using mowing heads
- 2.9 When using metal cutting attachments
- 2.10 Vibrations
- 2.11 Maintenance and Repairs
- 2.12 Symbols on Deflectors
- 2.13 Shoulder Strap/Harness
- 2.14 Mowing Head with Nylon Line
- 2.15 STIHL Polycut Mowing Head with Polymer Blades
- 2.16 Risk of Kickout (Blade Thrust) with Metal Cutting Attachments
- 2.17 Grass Cutting Blade
- 2.18 Brush Knife
- 2.19 Circular Saw Blade
- 3 Approved Combinations of Cutting Attachment, Deflector, Handle and Harness
- 4 Approved Power Tool Attachments
- 5 Mounting the Bike Handle
- 6 Mounting the Loop Handle
- 7 Adjusting the Throttle Cable
- 8 Fitting the Carrying Ring
- 9 Mounting the deflector
- 10 Mounting the Cutting Attachment
- 10.1 Placing power tool on the ground
- 10.2 Mounting Hardware for Cutting Attachments
- 10.3 Blocking the Shaft
- 10.4 Removing the Mounting Hardware
- 10.5 Mounting the Cutting Attachment
- 10.6 Fitting Mowing Head with Screw Mounting
- 10.7 Remove the mowing head.
- 10.8 Mounting Metal Cutting Attachments
- 10.9 Removing the Metal Cutting Attachment
- 11 Fuel
- 12 Fueling
- 13 Fitting the Harness
- 14 Balancing the Machine
- 15 Starting / Stopping the Engine
- 16 Transporting the Unit
- 17 Operating Instructions
- 18 Replacing the Air Filter
- 19 Adjusting the Carburetor
- 20 Spark Arresting Screen in Muffler
- 21 Spark Plug
- 22 Engine Running Behavior
- 23 Lubricating the Gearbox
- 24 Storing the Machine
- 25 Sharpening Metal Cutting Blades
- 26 Maintaining the Mowing Head
- 27 Maintenance and Care
- 28 Minimize Wear and Avoid Damage
- 29 Main Parts
- 30 Specifications
- 31 Maintenance and Repairs
- 32 Disposal
- 33 EC Declaration of Conformity
12.1 Preparations
0000-GXX-0476-A0
► Before fueling, clean the filler cap and the area
around it to ensure that no dirt falls into the
tank.
► Position the machine so that the tank cap
faces up.
12.2 Opening the Tank Cap
002BA447 KN
► Turn the cap counterclockwise until it can be
removed from the tank opening.
► Remove the tank cap.
12.3 Filling Up with Fuel
Take care not to spill fuel while fueling and do
not overfill the tank.
STIHL recommends you use the STIHL filler noz‐
zle for fuel (special accessory).
► Fill up with fuel.
12.4 Closing the Tank Cap
002BA448 KN
► Place the cap in the opening.
► Turn the cap clockwise as far as stop and
tighten it down as firmly as possible by hand.
13 Fitting the Harness
The type and style of the harness/shoulder strap
depend on the market.
The use of the shoulder strap is described in the
chapter on "Approved Combinations of Cutting
Attachment, Deflector, Handle and Harness".
13.1 Shoulder Strap
1
0000-GXX-0503-A0
2
► Put on the shoulder strap (1).
► Adjust the length of the strap so that the cara‐
biner (2) is about a hand’s width below your
right hip.
► Balance the machine – see "Balancing the
Machine".
13 Fitting the Harness English
0458-426-8321-B 23