Instruction Manual
Table Of Contents
- STIHL FS 91, 91 R
- 1 Guide to Using this Manual
- 2 Safety Precautions and Working Techniques
- 2.1 Clothing and equipment
- 2.2 Transporting the machine
- 2.3 Refueling
- 2.4 Before starting
- 2.5 Starting the engine
- 2.6 Holding and guiding the machine
- 2.7 While working
- 2.8 Using mowing heads
- 2.9 When using metal cutting attachments
- 2.10 Vibrations
- 2.11 Maintenance and Repairs
- 2.12 Symbols on Deflectors
- 2.13 Shoulder Strap/Harness
- 2.14 Mowing Head with Nylon Line
- 2.15 STIHL Polycut Mowing Head with Polymer Blades
- 2.16 Risk of Kickout (Blade Thrust) with Metal Cutting Attachments
- 2.17 Grass Cutting Blade
- 2.18 Brush Knife
- 2.19 Circular Saw Blade
- 3 Approved Combinations of Cutting Attachment, Deflector, Handle and Harness
- 4 Approved Power Tool Attachments
- 5 Mounting the Bike Handle
- 6 Mounting the Loop Handle
- 7 Adjusting the Throttle Cable
- 8 Fitting the Carrying Ring
- 9 Mounting the deflector
- 10 Mounting the Cutting Attachment
- 10.1 Placing power tool on the ground
- 10.2 Mounting Hardware for Cutting Attachments
- 10.3 Blocking the Shaft
- 10.4 Removing the Mounting Hardware
- 10.5 Mounting the Cutting Attachment
- 10.6 Fitting Mowing Head with Screw Mounting
- 10.7 Remove the mowing head.
- 10.8 Mounting Metal Cutting Attachments
- 10.9 Removing the Metal Cutting Attachment
- 11 Fuel
- 12 Fueling
- 13 Fitting the Harness
- 14 Balancing the Machine
- 15 Starting / Stopping the Engine
- 16 Transporting the Unit
- 17 Operating Instructions
- 18 Replacing the Air Filter
- 19 Adjusting the Carburetor
- 20 Spark Arresting Screen in Muffler
- 21 Spark Plug
- 22 Engine Running Behavior
- 23 Lubricating the Gearbox
- 24 Storing the Machine
- 25 Sharpening Metal Cutting Blades
- 26 Maintaining the Mowing Head
- 27 Maintenance and Care
- 28 Minimize Wear and Avoid Damage
- 29 Main Parts
- 30 Specifications
- 31 Maintenance and Repairs
- 32 Disposal
- 33 EC Declaration of Conformity
002BA662 KN
1
2
► Loosen the screw (1).
► Slide the carrying ring (2) along the drive tube.
► Tighten the screw (1) moderately.
► Allow the unit to hang freely.
► Check the position obtained:
Balanced positions
A
002BA034 KN
Mowing tools (A) such as mowing heads, grass
cutting blades and brush knives
► should just touch the ground.
B
002BA035 KN
Circular saw blades (B)
► should "hover" about 20 cm (8 in) above the
ground.
When the correct balanced position has been
reached:
► Tighten down the screw (1) on the carrying
ring firmly.
14.3 Disconnecting Machine from
Harness
002BA661 KN
2
1
1
1
2
2
► Press down the bar on the carabiner (1) and
pull the carrying ring (2) out of the carabiner.
14 Balancing the Machine English
0458-426-8321-B 25