Instruction Manual
Table Of Contents
- STIHL FS 91, 91 R
- 1 Guide to Using this Manual
- 2 Safety Precautions and Working Techniques
- 2.1 Clothing and equipment
- 2.2 Transporting the machine
- 2.3 Refueling
- 2.4 Before starting
- 2.5 Starting the engine
- 2.6 Holding and guiding the machine
- 2.7 While working
- 2.8 Using mowing heads
- 2.9 When using metal cutting attachments
- 2.10 Vibrations
- 2.11 Maintenance and Repairs
- 2.12 Symbols on Deflectors
- 2.13 Shoulder Strap/Harness
- 2.14 Mowing Head with Nylon Line
- 2.15 STIHL Polycut Mowing Head with Polymer Blades
- 2.16 Risk of Kickout (Blade Thrust) with Metal Cutting Attachments
- 2.17 Grass Cutting Blade
- 2.18 Brush Knife
- 2.19 Circular Saw Blade
- 3 Approved Combinations of Cutting Attachment, Deflector, Handle and Harness
- 4 Approved Power Tool Attachments
- 5 Mounting the Bike Handle
- 6 Mounting the Loop Handle
- 7 Adjusting the Throttle Cable
- 8 Fitting the Carrying Ring
- 9 Mounting the deflector
- 10 Mounting the Cutting Attachment
- 10.1 Placing power tool on the ground
- 10.2 Mounting Hardware for Cutting Attachments
- 10.3 Blocking the Shaft
- 10.4 Removing the Mounting Hardware
- 10.5 Mounting the Cutting Attachment
- 10.6 Fitting Mowing Head with Screw Mounting
- 10.7 Remove the mowing head.
- 10.8 Mounting Metal Cutting Attachments
- 10.9 Removing the Metal Cutting Attachment
- 11 Fuel
- 12 Fueling
- 13 Fitting the Harness
- 14 Balancing the Machine
- 15 Starting / Stopping the Engine
- 16 Transporting the Unit
- 17 Operating Instructions
- 18 Replacing the Air Filter
- 19 Adjusting the Carburetor
- 20 Spark Arresting Screen in Muffler
- 21 Spark Plug
- 22 Engine Running Behavior
- 23 Lubricating the Gearbox
- 24 Storing the Machine
- 25 Sharpening Metal Cutting Blades
- 26 Maintaining the Mowing Head
- 27 Maintenance and Care
- 28 Minimize Wear and Avoid Damage
- 29 Main Parts
- 30 Specifications
- 31 Maintenance and Repairs
- 32 Disposal
- 33 EC Declaration of Conformity
16.5 Circular Saw Blades
681BA302 KN
681BA275 KN
1.
2.
► Disconnect wire rod from the transport guard.
681BA276 KN
► Swing wire rod outwards.
► Fit transport guard on saw blade from below,
making sure the limit stop is properly seated in
the recess.
681BA277 KN
2.
► Swing wire rod into position.
► Hook wire rod to the transport guard.
17 Operating Instructions
17.1 During break-in period
A factory-new machine should not be run at high
revs (full throttle off load) for the first three tank
fillings. This avoids unnecessary high loads dur‐
ing the break-in period. As all moving parts have
to bed in during the break-in period, the frictional
resistances in the engine are greater during this
period. The engine develops its maximum power
after about 5 to 15 tank fillings.
17.2 During Operation
After a long period of full throttle operation, allow
the engine to run for a short while at idle speed
so that engine heat can be dissipated by the flow
of cooling air. This protects engine-mounted
components (ignition, carburetor) from thermal
overload.
17.3 After Finishing Work
Storing for a short period: Wait for the engine to
cool down. Empty the fuel tank and keep the
machine in a dry place, well away from sources
of ignition, until you need it again. For longer out-
of-service periods – see "Storing the Machine".
18 Replacing the Air Filter
Filters have an average life of more than a year.
Do not remove the filter cover or replace the air
filter as long as there is no noticeable loss of
power.
English 17 Operating Instructions
30 0458-426-8321-B