Instruction Manual
Table Of Contents
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Main Parts
- 4 Safety Symbols on the Products
- 5 IMPORTANT SAFETY INSTRUCTIONS
- 6 Maintenance, Repair and Storage
- 7 Battery Safety
- 8 Before Starting Work
- 9 Charging the Battery
- 10 LED Diagnostics and Acoustic Signals
- 11 Assembling the Trimmer / Brushcutter
- 12 Using a Battery Harness
- 13 Adjusting the Trimmer / Brushcutter
- 14 Inserting and Removing the Connecting Cord
- 15 Switching the Trimmer / Brushcutter On and Off
- 16 Checking the Power Tool
- 17 During Operation
- 18 After Finishing Work
- 19 Transporting
- 20 Storing
- 21 Cleaning
- 22 Inspection and Maintenance
- 23 Troubleshooting Guide
- 24 Specifications
- 25 Approved Deflector, Cutting Attachment, Handle and Harness Combinations
- 26 Replacement Parts and Equipment
- 27 Disposal
- 28 Limited Warranty
- 29 Trademarks
- 30 Addresses
- 1 Introducción
- 2 Acerca de este manual de instrucciones
- 3 Componentes importantes
- 4 Símbolos de seguridad en los productos
- 5 INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- 6 Mantenimiento, reparación y almacenamiento
- 7 Seguridad de la batería
- 8 Antes de empezar a trabajar
- 9 Carga de la batería
- 10 Diagnóstico por LED y señales acústicas
- 11 Armado de la motoguadaña / desmalezadora
- 12 Uso de un arnés para batería
- 13 Ajuste de la motoguadaña / desmalezadora
- 14 Inserción y retiro del cable de conexión
- 15 Encendido y apagado de la motoguadaña / desmalezadora
- 16 Comprobación de la herramienta motorizada
- 17 Durante el funcionamiento
- 18 Después de completar el trabajo
- 19 Transporte
- 20 Almacenamiento
- 21 Limpieza
- 22 Inspección y mantenimiento
- 23 Guía de solución de problemas
- 24 Especificaciones
- 25 Combinaciones aprobadas de deflector, accesorio de corte, mango y arnés
- 26 Piezas y equipos de repuesto
- 27 Eliminación
- 28 Garantía limitada
- 29 Marcas comerciales
- 30 Direcciones
0458-725-8621-B
29
English
11 Assembling the Trimmer / Brushcutter
To mount the skirt and line limiting blade:
► Insert the guide ridge on the bottom of the deflector (1)
into the groove on the skirt (2).
► Slide the skirt until it covers the entire bottom of the
deflector and clicks into place.
When the skirt is properly installed, it will cover the
pictogram embossed on the deflector indicating that use
with mowing heads is prohibited.
► Push the line limiting blade (3) into the guide groove of the
skirt.
► Insert and tighten the screw (4) until the line limiting blade
is securely in place.
11.4.2 Removing a Deflector
To remove a deflector:
► Switch off the power tool, @ 15.2.
► Remove the connecting cord, @ 14.2.
► Remove the screws (2).
► Remove the deflector (1)
To remove the skirt from the deflector:
► Insert the stop pin (2) in the hole in the skirt.
► Slide the skirt (1) off the guide ridge at the bottom of the
deflector.
11.5 Mounting and Removing a Mowing Head
11.5.1 Mounting a Mowing Head
WARNING
Use of wire or metal-reinforced line is not authorized and
could be extremely dangerous. Use only the cutting
attachments recommended in this manual, in combination
with the recommended deflector, @ 5.7.4.
WARNING
A damaged or loose cutting attachment or mowing head may
vibrate, crack, break or come off the trimmer / brushcutter,
which may result in serious or fatal injury or property
damage. Make sure the mowing head and cutting
attachment are properly tightened and in good condition
before starting work, @ 5.7.4.
3
2
4
0000-GXX-3028-A1
1
0000-GXX-3029-A0
1
2
1
0000-GXX-3030-A2
2