Instruction Manual
Table Of Contents
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Main Parts
- 4 Safety Symbols on the Products
- 5 IMPORTANT SAFETY INSTRUCTIONS
- 6 Maintenance, Repair and Storage
- 7 Battery Safety
- 8 Before Starting Work
- 9 Charging the Battery
- 10 LED Diagnostics and Acoustic Signals
- 11 Assembling the Trimmer / Brushcutter
- 12 Using a Battery Harness
- 13 Adjusting the Trimmer / Brushcutter
- 14 Inserting and Removing the Connecting Cord
- 15 Switching the Trimmer / Brushcutter On and Off
- 16 Checking the Power Tool
- 17 During Operation
- 18 After Finishing Work
- 19 Transporting
- 20 Storing
- 21 Cleaning
- 22 Inspection and Maintenance
- 23 Troubleshooting Guide
- 24 Specifications
- 25 Approved Deflector, Cutting Attachment, Handle and Harness Combinations
- 26 Replacement Parts and Equipment
- 27 Disposal
- 28 Limited Warranty
- 29 Trademarks
- 30 Addresses
- 1 Introducción
- 2 Acerca de este manual de instrucciones
- 3 Componentes importantes
- 4 Símbolos de seguridad en los productos
- 5 INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- 6 Mantenimiento, reparación y almacenamiento
- 7 Seguridad de la batería
- 8 Antes de empezar a trabajar
- 9 Carga de la batería
- 10 Diagnóstico por LED y señales acústicas
- 11 Armado de la motoguadaña / desmalezadora
- 12 Uso de un arnés para batería
- 13 Ajuste de la motoguadaña / desmalezadora
- 14 Inserción y retiro del cable de conexión
- 15 Encendido y apagado de la motoguadaña / desmalezadora
- 16 Comprobación de la herramienta motorizada
- 17 Durante el funcionamiento
- 18 Después de completar el trabajo
- 19 Transporte
- 20 Almacenamiento
- 21 Limpieza
- 22 Inspección y mantenimiento
- 23 Guía de solución de problemas
- 24 Especificaciones
- 25 Combinaciones aprobadas de deflector, accesorio de corte, mango y arnés
- 26 Piezas y equipos de repuesto
- 27 Eliminación
- 28 Garantía limitada
- 29 Marcas comerciales
- 30 Direcciones
0458-725-8621-B
30
English
11 Assembling the Trimmer / Brushcutter
Mowing heads other than FixCut 31-2
To mount a mowing head:
► Switch off the power tool, @ 15.2.
► Remove the connecting cord, @ 14.2.
► Position the unit so that you are facing the underside of
the deflector and the drive shaft is pointed upwards.
► Slip the thrust plate (2) onto the drive shaft (3), keeping
the side of the thrust plate with the smaller diameter facing
upwards toward the mowing head (1).
► Insert the stop pin (4) in the hole in the gearbox and rotate
the drive shaft until the stop pin slips into position and
blocks the rotation of the drive shaft.
► By hand, screw the mowing head counterclockwise onto
the drive shaft while keeping the stop pin inserted. The
drive shaft must be blocked with the stop pin to mount or
remove a cutting attachment.
► Continue screwing down the mowing head until it is
properly and securely attached.
► Remove the stop pin from the hole in the gearbox.
FixCut 31-2 Mowing Head
To mount the FixCut 31-2 mowing head:
► Switch off the power tool, @ 15.2.
► Remove the connecting cord, @ 14.2.
► Position the unit so that you are facing the underside of
the deflector and the drive shaft is pointed upwards.
► Slip the thrust plate (4) onto the drive shaft (5), keeping
the side of the thrust plate with the smaller diameter facing
upwards toward the FixCut 31-2 mowing head (3).
► Insert the stop pin (6) in the hole in the gearbox and rotate
the drive shaft until the stop pin slips into position and
blocks the rotation of the drive shaft.
► Place the mowing head directly on top of the thrust plate,
so that the collar of the thrust plate (4) engages to the
mowing head's mounting hole.
► Slip the thrust washer (2) onto the drive shaft. Keep the
arched side facing up and the flat side facing towards the
FixCut 31-2 mowing head.
► Screw on the nut (1) counterclockwise and tighten it down
until the mowing head is properly and securely attached.
► Remove the stop pin from the hole in the gearbox.
2
3
4
0000-GXX-3031-A0
1
4
1
1
0000-GXX-5065-A0
2
3
4
5
6