Instruction Manual
Table Of Contents
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Main Parts
- 4 Safety Symbols on the Products
- 5 IMPORTANT SAFETY INSTRUCTIONS
- 6 Maintenance, Repair and Storage
- 7 Battery Safety
- 8 Before Starting Work
- 9 Charging the Battery
- 10 LED Diagnostics and Acoustic Signals
- 11 Assembling the Trimmer / Brushcutter
- 12 Using a Battery Harness
- 13 Adjusting the Trimmer / Brushcutter
- 14 Inserting and Removing the Connecting Cord
- 15 Switching the Trimmer / Brushcutter On and Off
- 16 Checking the Power Tool
- 17 During Operation
- 18 After Finishing Work
- 19 Transporting
- 20 Storing
- 21 Cleaning
- 22 Inspection and Maintenance
- 23 Troubleshooting Guide
- 24 Specifications
- 25 Approved Deflector, Cutting Attachment, Handle and Harness Combinations
- 26 Replacement Parts and Equipment
- 27 Disposal
- 28 Limited Warranty
- 29 Trademarks
- 30 Addresses
- 1 Introducción
- 2 Acerca de este manual de instrucciones
- 3 Componentes importantes
- 4 Símbolos de seguridad en los productos
- 5 INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- 6 Mantenimiento, reparación y almacenamiento
- 7 Seguridad de la batería
- 8 Antes de empezar a trabajar
- 9 Carga de la batería
- 10 Diagnóstico por LED y señales acústicas
- 11 Armado de la motoguadaña / desmalezadora
- 12 Uso de un arnés para batería
- 13 Ajuste de la motoguadaña / desmalezadora
- 14 Inserción y retiro del cable de conexión
- 15 Encendido y apagado de la motoguadaña / desmalezadora
- 16 Comprobación de la herramienta motorizada
- 17 Durante el funcionamiento
- 18 Después de completar el trabajo
- 19 Transporte
- 20 Almacenamiento
- 21 Limpieza
- 22 Inspección y mantenimiento
- 23 Guía de solución de problemas
- 24 Especificaciones
- 25 Combinaciones aprobadas de deflector, accesorio de corte, mango y arnés
- 26 Piezas y equipos de repuesto
- 27 Eliminación
- 28 Garantía limitada
- 29 Marcas comerciales
- 30 Direcciones
0458-725-8621-B
33
English
12 Using a Battery Harness
► Remove the rider plate, thrust washer, metal cutting
attachment and thrust plate.
► Remove the stop pin from the hole in the gearbox.
NOTICE
After mounting or removing the cutting attachment, always
remove the stop pin used to block the rotation of the drive
shaft.
12.1 STIHL AR Backpack Battery
12.1.1 Positioning and Adjusting the Connecting Cord
WARNING
To reduce the risk of injury from tripping or losing control of
the power tool, always secure the connecting cord through
the backpack guides and with the hook and eye fasteners as
described below. Position and secure the connecting cord
so that it will not interfere with proper working technique or
your ability to maintain control of the power tool.
WARNING
Manage the cord to prevent it from contacting the
cutting/working attachment or catching on objects, which
could cause you to lose balance or control of the power tool,
resulting in serious personal injury and property damage.
The connecting cord can be secured in different positions
and adjusted to suit the height and reach of the operator.
The connecting cord can run through the guide on the
shoulder strap (Illustration A), or along the back
plate (Illustration B). Secure the connecting cord to the
backpack frame with the hook and eye fasteners (1). Always
secure the connecting cord using the guide or hook and eye
fasteners on the side of the body on which the power tool is
held and controlled. Do not allow the connecting cord to
swing across your body or hang at your side.
The length of the connecting cord can be adjusted by
making a loop around the top (Illustration C) or on the side
(Illustration D) of the backpack battery with the hook and eye
fasteners.
12 Using a Battery Harness
0000-GXX-2801-A2
1
1
1
1
1
1
B
A
0000-GXX-2803-A1
D
C