Instruction Manual
Table Of Contents
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Main Parts
- 4 Safety Symbols on the Products
- 5 IMPORTANT SAFETY INSTRUCTIONS
- 6 Maintenance, Repair and Storage
- 7 Battery Safety
- 8 Before Starting Work
- 9 Charging the Battery
- 10 LED Diagnostics and Acoustic Signals
- 11 Assembling the Trimmer / Brushcutter
- 12 Using a Battery Harness
- 13 Adjusting the Trimmer / Brushcutter
- 14 Inserting and Removing the Connecting Cord
- 15 Switching the Trimmer / Brushcutter On and Off
- 16 Checking the Power Tool
- 17 During Operation
- 18 After Finishing Work
- 19 Transporting
- 20 Storing
- 21 Cleaning
- 22 Inspection and Maintenance
- 23 Troubleshooting Guide
- 24 Specifications
- 25 Approved Deflector, Cutting Attachment, Handle and Harness Combinations
- 26 Replacement Parts and Equipment
- 27 Disposal
- 28 Limited Warranty
- 29 Trademarks
- 30 Addresses
- 1 Introducción
- 2 Acerca de este manual de instrucciones
- 3 Componentes importantes
- 4 Símbolos de seguridad en los productos
- 5 INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- 6 Mantenimiento, reparación y almacenamiento
- 7 Seguridad de la batería
- 8 Antes de empezar a trabajar
- 9 Carga de la batería
- 10 Diagnóstico por LED y señales acústicas
- 11 Armado de la motoguadaña / desmalezadora
- 12 Uso de un arnés para batería
- 13 Ajuste de la motoguadaña / desmalezadora
- 14 Inserción y retiro del cable de conexión
- 15 Encendido y apagado de la motoguadaña / desmalezadora
- 16 Comprobación de la herramienta motorizada
- 17 Durante el funcionamiento
- 18 Después de completar el trabajo
- 19 Transporte
- 20 Almacenamiento
- 21 Limpieza
- 22 Inspección y mantenimiento
- 23 Guía de solución de problemas
- 24 Especificaciones
- 25 Combinaciones aprobadas de deflector, accesorio de corte, mango y arnés
- 26 Piezas y equipos de repuesto
- 27 Eliminación
- 28 Garantía limitada
- 29 Marcas comerciales
- 30 Direcciones
0458-725-8621-B
40
English
14 Inserting and Removing the Connecting Cord
If the mowing head or the metal cutting attachment will not
rest gently on or just above the ground:
► Loosen the screw on the carrying ring (2).
► Slide the carrying ring (1) along the drive tube and re-
tighten the screw.
► Allow the trimmer / brushcutter to hang freely again.
Repeat and re-adjust as necessary to achieve the proper
balance.
► Once the cutting attachment is properly positioned for
work, tighten the screw firmly and ensure that the carrying
ring is secure.
14.1 Inserting the Connecting Cord
WARNING
Never use a malfunctioning, damaged, cracked, leaking or
deformed battery, @ 7. Use and store the battery only
within an ambient temperature range of 14 °F to 122 °F (- 10
°C to 50 °C), @ 7.
To insert the connecting cord:
► Line up the arrow on the connecting cord plug (2) with the
arrow on the socket (1).
► Push the plug straight into the socket with steady, even
pressure until it is fully inserted.
14.2 Removing the Connecting Cord
WARNING
To reduce the risk of severe personal injury from unintended
activation, always remove the connecting cord before
assembling, transporting, adjusting, cleaning, servicing,
maintaining or storing the trimmer / brushcutter. Remove the
connecting cord in the event of malfunction or emergency
and any time the trimmer / brushcutter is not in use.
WARNING
To reduce the risk of electric shock or personal injury from
the loss of control, always switch off the trimmer before
removing the connecting cord from the socket.
To remove the connecting cord:
► Release trigger switch.
► Pull the plug straight out of the trimmer socket with steady,
even pressure.
14 Inserting and Removing the
Connecting Cord
1
2
0000-GXX-3033-A0
0000-GXX-3086-A0
2
1