Instruction Manual
Table Of Contents
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Main Parts
- 4 Safety Symbols on the Products
- 5 IMPORTANT SAFETY INSTRUCTIONS
- 6 Maintenance, Repair and Storage
- 7 Battery Safety
- 8 Before Starting Work
- 9 Charging the Battery
- 10 LED Diagnostics and Acoustic Signals
- 11 Assembling the Trimmer / Brushcutter
- 12 Using a Battery Harness
- 13 Adjusting the Trimmer / Brushcutter
- 14 Inserting and Removing the Connecting Cord
- 15 Switching the Trimmer / Brushcutter On and Off
- 16 Checking the Power Tool
- 17 During Operation
- 18 After Finishing Work
- 19 Transporting
- 20 Storing
- 21 Cleaning
- 22 Inspection and Maintenance
- 23 Troubleshooting Guide
- 24 Specifications
- 25 Approved Deflector, Cutting Attachment, Handle and Harness Combinations
- 26 Replacement Parts and Equipment
- 27 Disposal
- 28 Limited Warranty
- 29 Trademarks
- 30 Addresses
- 1 Introducción
- 2 Acerca de este manual de instrucciones
- 3 Componentes importantes
- 4 Símbolos de seguridad en los productos
- 5 INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- 6 Mantenimiento, reparación y almacenamiento
- 7 Seguridad de la batería
- 8 Antes de empezar a trabajar
- 9 Carga de la batería
- 10 Diagnóstico por LED y señales acústicas
- 11 Armado de la motoguadaña / desmalezadora
- 12 Uso de un arnés para batería
- 13 Ajuste de la motoguadaña / desmalezadora
- 14 Inserción y retiro del cable de conexión
- 15 Encendido y apagado de la motoguadaña / desmalezadora
- 16 Comprobación de la herramienta motorizada
- 17 Durante el funcionamiento
- 18 Después de completar el trabajo
- 19 Transporte
- 20 Almacenamiento
- 21 Limpieza
- 22 Inspección y mantenimiento
- 23 Guía de solución de problemas
- 24 Especificaciones
- 25 Combinaciones aprobadas de deflector, accesorio de corte, mango y arnés
- 26 Piezas y equipos de repuesto
- 27 Eliminación
- 28 Garantía limitada
- 29 Marcas comerciales
- 30 Direcciones
0458-725-8621-B
48
English
22 Inspection and Maintenance
To lubricate the gearbox:
► Remove the screw plug (2).
► If no grease can be seen on the inside of the screw plug,
screw the tube (1) of STIHL gear lubricant into the filler
hole.
► Squeeze no more than 0.2 oz (5 g) of STIHL gear
lubricant into the gearbox.
► Remove the tube of STIHL gear lubricant.
► Insert the screw plug and tighten it down firmly.
NOTICE
Do not completely fill the gearbox with grease.
22.4 Replacing the Trimmer Line on an AutoCut 25
-
2
Mowing Head
WARNING
Use of wire or metal-reinforced line is not authorized and
could be extremely dangerous. Use only the cutting
attachments recommended in this manual, in combination
with the recommended deflector.
WARNING
A damaged or loose cutting attachment or mowing head may
vibrate, crack, break or come off the trimmer / brushcutter,
which may result in serious or fatal injury or property
damage. Make sure the mowing head and cutting
attachment are properly and securely tightened and in good
condition before starting work.
► Switch off the power tool, @ 15.2.
► Remove the connecting cord, @ 14.2.
► Remove the mowing head, @ 11.5.2.
► Press both tabs (1) and remove the cover (2).
► Press down on the spool (3), turn it clockwise to release
the spool and pull up to remove it.
► Remove the remaining trimmer line (4) and dispose of it.
► If you use trimmer line with a diameter of 0.095 in.
(2.4 mm), cut a 33 ft. m (10 m) length of nylon line from
the reel and then cut it in half, making two 16.5 ft. (5 m)
lengths.
► Insert the first 16.5 ft. (5 m) length of line into the
eyelet (5) nearest the notches (6) until it stops.
2
1
0000-GXX-3044-A0
0000-GXX-4033-A0
1
1
4
2
3
0000-GXX-4034-A0
6
5