Instruction Manual
Table Of Contents
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Main Parts
- 4 Safety Symbols on the Products
- 5 General Power Tool Safety Warnings
- 6 IMPORTANT SAFETY INSTRUCTIONS
- 7 Battery Safety
- 8 Maintenance, Repair and Storage
- 9 Before Starting Work
- 10 Charging the Battery
- 11 LED Diagnostics and Acoustic Signals
- 12 STIHL AR Backpack Battery
- 13 Assembling the Hedge Trimmer
- 14 Inserting and Removing the Battery
- 15 Switching the Hedge Trimmer On and Off
- 16 Checking the Controls
- 17 During Operation
- 18 After Finishing Work
- 19 Transporting the Hedge Trimmer and Battery
- 20 Storing the Hedge Trimmer and Battery
- 21 Cleaning
- 22 Inspection and Maintenance
- 23 Troubleshooting Guide
- 24 Specifications
- 25 Approved Harness Combinations
- 26 Replacement Parts and Equipment
- 27 Disposal
- 28 Limited Warranty
- 29 Trademarks
- 30 Addresses
- 1 Introducción
- 2 Acerca de este manual de instrucciones
- 3 Componentes importantes
- 4 Símbolos de seguridad en los productos
- 5 Advertencias generales de seguridad para herramientas motorizadas
- 5.1 Introducción
- 5.2 Seguridad en la zona de trabajo
- 5.3 Seguridad eléctrica
- 5.4 Seguridad personal
- 5.5 Uso y cuidado de la herramienta motorizada
- 5.6 Uso y cuidado de la herramienta con batería
- 5.7 Mantenimiento
- 5.8 Advertencias de seguridad del cortasetos
- 5.9 Advertencias de seguridad del cortasetos de alcance extendido
- 6 INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- 7 Seguridad de la batería
- 8 Mantenimiento, reparación y almacenamiento
- 9 Antes de empezar a trabajar
- 10 Carga de la batería
- 11 Diagnóstico por LED y señales acústicas
- 12 Batería de mochila STIHL AR
- 13 Armado del cortasetos
- 14 Colocación y extracción de la batería.
- 15 Encendido y apagado del cortasetos
- 16 Revisión de los controles
- 17 Durante el funcionamiento
- 18 Después de completar el trabajo
- 19 Transporte del cortasetos y de la batería
- 20 Almacenamiento del cortasetos y de la batería
- 21 Limpieza
- 22 Inspección y mantenimiento
- 23 Guía de solución de problemas
- 24 Especificaciones
- 25 Combinaciones de arnés aprobadas
- 26 Piezas y equipos de repuesto
- 27 Eliminación
- 28 Garantía limitada
- 29 Marcas comerciales
- 30 Direcciones
0458-185-8621-A
31
English
18 After Finishing Work
► Cut the other side of the hedge in the same way.
► If cutting performance deteriorates: Sharpen the cutting
blades.
Cutting top of hedge
► Hold the cutting attachment at an angle of 0° to 10° as you
move the cutting attachment horizontally, using both sides
of the cutting attachment (see illustration above).
► If cutting performance deteriorates: Sharpen the cutting
blades.
Cutting overhead
WARNING
Any working position over shoulder height is tiring. To
reduce the risk of injury from fatigue, never hold the machine
with your rear hand on the control handle above shoulder
height. Set the adjustable cutter blades to the most suitable
angle so that the unit can be held at a lower, less tiring
position while providing adequate reach. Take frequent
breaks.
► Set the cutting attachment to a suitable angle.
► Hold the cutting attachment at an angle of 0° to 10° as you
move the cutting attachment horizontally, using both sides
of the cutting attachment (see illustration above).
► If cutting performance deteriorates: Sharpen the cutting
blades.
18.1 Preparing for Transportation or Storage
WARNING
To reduce the risk of personal injury from unintended
activation or unauthorized use, switch off the motor, ensure
the cutting blades have stopped and remove the battery
before transporting the hedge trimmer or putting it down.
To prepare the hedge trimmer for transportation or storage:
► Switch off the hedge trimmer, @ 15.2.
► Remove the battery, @ 14.2.
► For a hedge trimmer with adjustable shaft, adjust the shaft
to its shortest length, @ 17.2
► Slide a blade scabbard over the cutting blades so that it
covers the entire cutting attachment.
► If the hedge trimmer or battery became wet during
operation, allow them to dry completely before charging or
storing.
0000097227_002
18 After Finishing Work
0000097226_001