STIHL KM 56 R Instruction Manual
English KombiSystem Guide to Using this Manual Safety Precautions and Working Techniques Approved KombiTools Mounting the Loop Handle Carrying ring Fuel Fueling Starting / Stopping the Engine Operating Instructions Cleaning the Air Filter Adjusting the Carburetor Spark Plug Engine Running Behavior Storing the Machine Inspections and Maintenance by Dealer Maintenance and Care Main Parts Specifications Maintenance and Repairs Disposal EC Declaration of Conformity © ANDREAS STIHL AG & Co.
English KombiSystem In the STIHL KombiSystem a number of different KombiEngines and KombiTools can be combined to produce a power tool. In this instruction manual the functional unit formed by the KombiEngine and KombiTool is referred to as the power tool. Therefore, the separate instruction manuals for the KombiEngine and KombiTool should be used together for the power tool.
English Safety Precautions and Working Techniques The user is responsible for accidents or risks involving third parties or their property. Special safety precautions must be observed when operating a power tool. The machine should only be provided or loaned to people familiar with this model and its operation. The KombiEngine and KombiTool User Manuals should always be handed over with the machine.
English allow your clothes to be splashed with fuel. If that happens, change your clothes at once. Transporting the machine – Check the choke lever, throttle trigger and throttle trigger lockout for smooth action - throttle trigger must return automatically to idle position.
English Use your power tool only in the areas specified in the KombiTool User Manual. power tool securely. The attachment must be clear of the ground and all other obstructions because it may begin to run when the engine starts. Do not drop-start the power tool – start the engine as described in the User Manual. Note that the attachment continues to run for a short period after you let go of the throttle trigger – flywheel effect.
English Dust, fumes and smoke produced while working may be hazardous to health! Wear respiratory protection in case of heavy dust or smoke emission. If your power tool is subjected to unusually high loads for which it was not designed (e.g. heavy impact or a fall), always check that it is in good condition before continuing work – see also "Before Starting". Check in particular that the fuel system has no leaks and the safety equipment is fully operative.
English Mounting the Barrier Bar Mounting the Loop Handle The following STIHL KombiTools may be attached to the KombiEngine: FSB-KM HL-KM 145° HL-KM 0° FH-KM 145° BG-KM HT-KM BF-KM FCB-KM FCS-KM SP-KM KB-KM KW-KM 1) The included barrier bar on the loop handle must be used - see also "Mounting the Loop Handle” KM 56 R, KM 56 RC 1 2 4 002BA586 KN FS-KM 1) Intended use Scythe with mowing head Scythe with grass cutting blade Scythe with mowing head Long reach hedge trimmer, adjustable Long-reach hedge
English Orienting and Securing the Loop Handle 2 4 A 2 3 1 Insert the square nuts (1) in the barrier bar (2) – the holes must line up 7 7 N Insert the clamp (3) in the loop handle (4) and position them together on the shaft (5) N Position the clamp (6) against the shaft N Position the barrier bar (2) – note position! N Line up the holes N Insert the screws (7) in the holes and screw them into the barrier bar as far as they will go N Go to "Adjusting and Securing the Loop Handle" 002BA59
English Carrying ring Fuel Your engine requires a mixture of gasoline and engine oil. 547BA008 KN WARNING The carrying ring is integrated in the front end of the control handle. For health reasons, avoid direct skin contact with gasoline and avoid inhaling gasoline vapor. STIHL MotoMix STIHL recommends the use of STIHL MotoMix. This ready-to-use fuel mix contains no benzol or lead, has a high octane rating and ensures that you always use the right mix ratio.
English Store fuel only in approved safety-type fuel canisters in a dry, cool and safe location protected from light and the sun. Filling up with fuel Fueling Take care not to spill fuel while fueling and do not overfill the tank. STIHL recommends you use the STIHL filler nozzle (special accessory). Preparations Fuel mix ages – only mix sufficient fuel for a few weeks work. Do not store fuel mix for longer than 30 days.
English Also use this setting if the engine has been running but is still cold. Starting the Engine Starting / Stopping the Engine Cranking Controls N 1 1 2 3 002BA269 KN 2 N Place the unit on the ground: Check that the working tool is not touching the ground or any other obstacles – see also "Starting / Stopping the Engine" in the KombiTool instruction manual. N Make sure you have a safe and secure footing.
English As soon as the engine runs Engine does not start in warm start position < N Move the choke lever to g and continue cranking until the engine runs. 547BA021 KN If the engine does not start 547BA020 KN N N Hold the starter grip with your right hand. Version without ErgoStart N Pull the starter grip slowly until you feel it engage and then give it a brisk strong pull. Press down the throttle trigger lockout and open the throttle – the choke lever moves to the run position F.
English If there is a noticeable loss of engine power A factory-new machine should not be run at high revs (full throttle off load) for the first three tank fillings. This avoids unnecessary high loads during the break-in period. As all moving parts have to bed in during the break-in period, the frictional resistances in the engine are greater during this period. The engine develops its maximum power after about 5 to 15 tank fillings.
English Adjusting the Carburetor WARNING The carburetor comes from the factory with a standard setting. On this machine it is no longer necessary to adjust the carburetor. If the working tool or cutting attachment continues to run when the engine is idling, have your machine checked and repaired by your servicing dealer. Spark Plug N If the engine is down on power, difficult to start or runs poorly at idle speed, first check the spark plug.
English Checking the Spark Plug N Use resistor type spark plugs with a properly tightened adapter nut. 000BA039 KN Installing the Spark Plug A N Clean dirty spark plug. N Check electrode gap (A) and readjust if necessary – see "Specifications". N Rectify the problems which have caused fouling of the spark plug. N Screw the spark plug into the cylinder. N Press the boot firmly onto the spark plug.
English Storing the Machine For periods of 3 months or longer N Drain and clean the fuel tank in a well ventilated area. N Dispose of fuel properly in accordance with local environmental requirements. N Run the engine until the carburetor is dry – this helps prevent the carburetor diaphragms sticking together. N Thoroughly clean the machine – pay special attention to the air filter. N Remove, clean and check the attachment. Coat metal parts with corrosion inhibiting oil.
English Complete machine Control handle Air filter Manual fuel pump Pickup body (filter) in fuel tank Visual inspection (condition, leaks) X Clean X X Check operation X X Clean X Replace X X Check X Have repaired by servicing dealer1) X Check X Replace X Fuel tank Clean Carburetor Check idle adjustment – the working/cutting attachment must not run X X X Cooling air inlet X X Readjust electrode gap X Replace after every 100 operating hours Visual inspection X Clean X 1) H
English Main Parts 1 2 4 5 3 9 15 18 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 # 20 14 13 6 12 7 8 11 # 18 10 540BA010 STI 17 19 Manual fuel pump Fuel cap Tank Starter grip Muffler Carburetor adjusting screws Choke lever Air filter cover Spark plug boot Machine support Throttle trigger Throttle trigger lockout Stop switch Carrying ring Loop handle Barrier bar Shaft Coupling sleeve Wing screw Sleeve Serial number KM 56 R, KM 56 RC
English Sound and Vibration Levels Specifications Engine For further details on compliance with Vibration Directive 2002/44/EC see www.stihl.com/vib Single cylinder two-stroke engine KombiTool Displacement: Bore: Stroke: Engine power to ISO 8893: Idle speed: Cut-off speed (rated): For version see "Approved KombiTools". 27.2 cc 34 mm 30 mm 0.8 kW (1.1 bhp) at 8,500 rpm 2,800 rpm 10,000 rpm Ignition System Electronic magneto ignition Spark plug (resistor type): Electrode gap: NGK CMR 6 H 0.
English Users of this machine may only carry out the maintenance and service work described in this user manual. All other repairs must be carried out by a servicing dealer. STIHL recommends that you have servicing and repair work carried out exclusively by an authorized STIHL servicing dealer. STIHL dealers are regularly given the opportunity to attend training courses and are supplied with the necessary technical information.
English Done at Waiblingen, 03.02.2020 ANDREAS STIHL AG & Co. KG pp Dr.
0458-540-8321-C AUS G www.stihl.