Instruction Manual
Table Of Contents
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Main Parts
- 4 Safety Symbols on the Product
- 5 IMPORTANT SAFETY INSTRUCTIONS
- 6 Kickback and Other Reactive Forces
- 7 Emergency Situations
- 8 Proper Techniques for Basic Bucking, Limbing, Pruning and Felling
- 9 Maintenance, Repair and Storage
- 10 Before Starting Work
- 11 Assembling the Chain Saw
- 12 Lubricating the Saw Chain and Guide Bar
- 13 The Chain Brake
- 14 Mixing Fuel and Refueling the Chain Saw
- 15 Starting the Engine
- 16 Shutting Off the Engine
- 17 Checking the Chain Saw
- 18 Adjusting the Carburetor
- 19 After Finishing Work
- 20 Transporting
- 21 Storing
- 22 Cleaning
- 23 Inspection and Maintenance
- 24 Troubleshooting Guide
- 25 Specifications
- 26 Combinations of Guide Bars and Saw Chains
- 27 Replacement Parts and Equipment
- 28 Disposal
- 29 Limited Warranty
- 30 Emission Control Warranty
- 31 Trademarks
- 32 Addresses
- 1 Introducción
- 2 Acerca de este manual de instrucciones
- 3 Componentes importantes
- 4 Símbolos de seguridad en el producto
- 5 INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- 6 Contragolpe y otras fuerzas reactivas
- 7 Situaciones de emergencia
- 8 Técnicas adecuadas para el tronzado, el desramado, la poda y la tala básicos
- 9 Mantenimiento, reparación y almacenamiento
- 10 Antes de empezar a trabajar
- 11 Armado de la motosierra
- 12 Lubricación de la cadena de aserrado y de la espada
- 13 El freno de cadena
- 14 Mezcla del combustible y carga de combustible en la motosierra
- 15 Arranque del motor
- 16 Apagado del motor
- 17 Revisión de la motosierra
- 18 Ajuste del carburador
- 19 Después de completar el trabajo
- 20 Transporte
- 21 Almacenamiento
- 22 Limpieza
- 23 Inspección y mantenimiento
- 24 Guía de solución de problemas
- 25 Especificaciones
- 26 Combinaciones de espadas y cadenas de aserrado
- 27 Piezas y equipos de repuesto
- 28 Eliminación
- 29 Garantía limitada
- 30 Garantía del sistema de control de emisiones
- 31 Marcas comerciales
- 32 Direcciones
0458-787-8621-A
36
English
11 Assembling the Chain Saw
11.2 Mounting and Removing the Guide Bar and
Chain
11.2.1 Mounting the Guide Bar and Chain
WARNING
The chain has many sharp cutters. If they contact your flesh,
they will cut you, even if the chain is not moving, @ 5.4.
Always wear heavy-duty work gloves when mounting or
otherwise handling the chain, @ 5.3.
To mount the guide bar and chain:
► Shut off the engine, @ 16.
► Unscrew the nuts (1).
► Remove the chain sprocket cover (2).
► Turn the side chain tensioner (3) counter-clockwise until
the tensioning gear (4) sits flush against the housing.
► Position the chain in the groove of the guide bar, starting
at the tip.
► Make sure that the cutters in the groove on the top side of
the guide bar face the tip of the bar. STIHL chains are
manufactured with arrows on the tie straps to help the
operator determine the proper direction of the chain.
Arrows on the tie straps on the top of the bar must point
toward the bar tip.
► Point the guide bar tip away from the chain sprocket (7).
► Place the chain around the chain sprocket.
► Slide the guide bar (6) over the collar screws (5). The
head of the collar screw must protrude into the oblong
hole.
► Fit the pin of the tensioning gear in the hole (8) of the
guide bar.
► Disengage the chain brake, @ 13.2.
3
0000-GXX-2734-A0
2
4
1
0000-GXX-2130-A0
0000-GXX-2735-A0
7
0000-GXX-2928-A0