Instruction Manual
Table Of Contents
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Main Parts
- 4 Safety Symbols on the Product
- 5 IMPORTANT SAFETY INSTRUCTIONS
- 6 Kickback and Other Reactive Forces
- 7 Emergency Situations
- 8 Proper Techniques for Basic Bucking, Limbing, Pruning and Felling
- 9 Maintenance, Repair and Storage
- 10 Before Starting Work
- 11 Assembling the Chain Saw
- 12 Lubricating the Saw Chain and Guide Bar
- 13 The Chain Brake
- 14 Mixing Fuel and Refueling the Chain Saw
- 15 Starting the Engine
- 16 Shutting Off the Engine
- 17 Checking the Chain Saw
- 18 Adjusting the Carburetor
- 19 After Finishing Work
- 20 Transporting
- 21 Storing
- 22 Cleaning
- 23 Inspection and Maintenance
- 24 Troubleshooting Guide
- 25 Specifications
- 26 Combinations of Guide Bars and Saw Chains
- 27 Replacement Parts and Equipment
- 28 Disposal
- 29 Limited Warranty
- 30 Emission Control Warranty
- 31 Trademarks
- 32 Addresses
- 1 Introducción
- 2 Acerca de este manual de instrucciones
- 3 Componentes importantes
- 4 Símbolos de seguridad en el producto
- 5 INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- 6 Contragolpe y otras fuerzas reactivas
- 7 Situaciones de emergencia
- 8 Técnicas adecuadas para el tronzado, el desramado, la poda y la tala básicos
- 9 Mantenimiento, reparación y almacenamiento
- 10 Antes de empezar a trabajar
- 11 Armado de la motosierra
- 12 Lubricación de la cadena de aserrado y de la espada
- 13 El freno de cadena
- 14 Mezcla del combustible y carga de combustible en la motosierra
- 15 Arranque del motor
- 16 Apagado del motor
- 17 Revisión de la motosierra
- 18 Ajuste del carburador
- 19 Después de completar el trabajo
- 20 Transporte
- 21 Almacenamiento
- 22 Limpieza
- 23 Inspección y mantenimiento
- 24 Guía de solución de problemas
- 25 Especificaciones
- 26 Combinaciones de espadas y cadenas de aserrado
- 27 Piezas y equipos de repuesto
- 28 Eliminación
- 29 Garantía limitada
- 30 Garantía del sistema de control de emisiones
- 31 Marcas comerciales
- 32 Direcciones
0458-787-8621-A
51
English
18 Adjusting the Carburetor
► Fully depress the throttle trigger for at least
30 seconds (B) and hold it in that position.
The engine will accelerate, the chain will rotate and the
chain saw will be calibrated. Engine speed will vary
noticeably during calibration.
► If the engine shuts off, retry to calibrate. The calibration
was aborted.
► If the engine keeps shutting off, engage the chain brake
and have the chain saw inspected by an authorized STIHL
servicing dealer before further use.
► Release the throttle trigger as soon as the engine speed
drops noticeably (C).
The engine will run at idling speed. The chain saw is
successfully calibrated and ready for operation.
NOTICE
The chain saw may be incorrectly calibrated if the throttle
trigger is not kept fully depressed during calibration. This
may result in damage to the saw.
NOTICE
The calibration process will be aborted if the throttle trigger
is released before the saw is properly calibrated. It is then
necessary to restart the entire calibration process.
18.3 Winter Operation
The carburetor may ice up when the saw is used at ambient
temperatures below 50 °F (10 °C). To prevent icing, the
shutter must be converted to allow warm air from around the
engine to heat the carburetor.
► Shut off the engine, @ 16.
► Engage the chain brake, @ 13.1.
► Open the shroud locks (1) by turning them 1/4 turn
counter-clockwise with the combination wrench.
► Remove the shroud (2).
► Pull out the shutter (3).
► Re-insert the shutter as shown above. The "winter"
symbol (4) points toward the chain saw.
► Push the shutter into the slot until it stops.
► Place the shroud in position.
► Tighten the shroud locks until you hear an audible click.
NOTICE
The winter operation setting should only be used in ambient
temperatures below 50 °F (10 °C). Use at higher
temperatures may cause the engine to overheat, resulting in
permanent damage. Always remember to return the shutter
to the configuration that is appropriate for ambient
temperature conditions.
0000-GXX-3163-A0
11
3
4
3
0000-GXX-3164-A0