Instruction Manual
Table Of Contents
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Main Parts
- 4 Safety Symbols on the Product
- 5 IMPORTANT SAFETY INSTRUCTIONS
- 6 Kickback and Other Reactive Forces
- 7 Emergency Situations
- 8 Proper Techniques for Basic Bucking, Limbing, Pruning and Felling
- 9 Maintenance, Repair and Storage
- 10 Before Starting Work
- 11 Assembling the Chain Saw
- 12 Lubricating the Saw Chain and Guide Bar
- 13 The Chain Brake
- 14 Mixing Fuel and Refueling the Chain Saw
- 15 Starting the Engine
- 16 Shutting Off the Engine
- 17 Checking the Chain Saw
- 18 Adjusting the Carburetor
- 19 After Finishing Work
- 20 Transporting
- 21 Storing
- 22 Cleaning
- 23 Inspection and Maintenance
- 24 Troubleshooting Guide
- 25 Specifications
- 26 Combinations of Guide Bars and Saw Chains
- 27 Replacement Parts and Equipment
- 28 Disposal
- 29 Limited Warranty
- 30 Emission Control Warranty
- 31 Trademarks
- 32 Addresses
- 1 Introducción
- 2 Acerca de este manual de instrucciones
- 3 Componentes importantes
- 4 Símbolos de seguridad en el producto
- 5 INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- 6 Contragolpe y otras fuerzas reactivas
- 7 Situaciones de emergencia
- 8 Técnicas adecuadas para el tronzado, el desramado, la poda y la tala básicos
- 9 Mantenimiento, reparación y almacenamiento
- 10 Antes de empezar a trabajar
- 11 Armado de la motosierra
- 12 Lubricación de la cadena de aserrado y de la espada
- 13 El freno de cadena
- 14 Mezcla del combustible y carga de combustible en la motosierra
- 15 Arranque del motor
- 16 Apagado del motor
- 17 Revisión de la motosierra
- 18 Ajuste del carburador
- 19 Después de completar el trabajo
- 20 Transporte
- 21 Almacenamiento
- 22 Limpieza
- 23 Inspección y mantenimiento
- 24 Guía de solución de problemas
- 25 Especificaciones
- 26 Combinaciones de espadas y cadenas de aserrado
- 27 Piezas y equipos de repuesto
- 28 Eliminación
- 29 Garantía limitada
- 30 Garantía del sistema de control de emisiones
- 31 Marcas comerciales
- 32 Direcciones
0458-787-8621-A
57
English
23 Inspection and Maintenance
23.1 Inspection and Maintenance Chart
1)
STIHL recommends an authorized STIHL servicing dealer
23 Inspection and Maintenance
The following maintenance intervals are examples and apply for normal
operating conditions. Actual use and your experience will determine the
frequency of required inspection and maintenance.
Before starting
work
After finishing work
or daily
Whenever fueling
Weekly
Monthly
Yearly
Relevant Chapter
Complete Machine Visual inspection XX
Clean X @ 22.1
Controls Check function and condition XX @ 17.2
Chain Brake Check function X @ 17.1
Chain Oil Tank Clean
1)
XX
Chain Lubrication Check chain oil flow rate X @ 17.3
Fuel Tank Clean
1)
X
Fuel Pick-Up Body / Filter Clean
1)
X
Replace
1)
X
Air Filter Clean X @ 22.3
Saw Chain Check chain tension XX @ 11.3
Sharpen
1)
XXX @ 23.5
Guide Bar Inspect for proper groove depth and
spread
X @ 23.4
Deburr X @ 23.4
Chain Sprocket Inspect X @ 23.4
Chain catcher on sprocket cover Inspect
1)
X
Air intake on fan housing Clean XX
Cylinder fins Clean XX
Spark arresting screen in muffler Check and Clean
1)
X