Instruction Manual
Table Of Contents
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Main Parts
- 4 Safety Symbols on the Product
- 5 IMPORTANT SAFETY INSTRUCTIONS
- 6 Kickback and Other Reactive Forces
- 7 Emergency Situations
- 8 Proper Techniques for Basic Bucking, Limbing, Pruning and Felling
- 9 Maintenance, Repair and Storage
- 10 Before Starting Work
- 11 Assembling the Chain Saw
- 12 Lubricating the Saw Chain and Guide Bar
- 13 The Chain Brake
- 14 Mixing Fuel and Refueling the Chain Saw
- 15 Starting the Engine
- 16 Shutting Off the Engine
- 17 Checking the Chain Saw
- 18 Adjusting the Carburetor
- 19 After Finishing Work
- 20 Transporting
- 21 Storing
- 22 Cleaning
- 23 Inspection and Maintenance
- 24 Troubleshooting Guide
- 25 Specifications
- 26 Combinations of Guide Bars and Saw Chains
- 27 Replacement Parts and Equipment
- 28 Disposal
- 29 Limited Warranty
- 30 Emission Control Warranty
- 31 Trademarks
- 32 Addresses
- 1 Introducción
- 2 Acerca de este manual de instrucciones
- 3 Componentes importantes
- 4 Símbolos de seguridad en el producto
- 5 INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- 6 Contragolpe y otras fuerzas reactivas
- 7 Situaciones de emergencia
- 8 Técnicas adecuadas para el tronzado, el desramado, la poda y la tala básicos
- 9 Mantenimiento, reparación y almacenamiento
- 10 Antes de empezar a trabajar
- 11 Armado de la motosierra
- 12 Lubricación de la cadena de aserrado y de la espada
- 13 El freno de cadena
- 14 Mezcla del combustible y carga de combustible en la motosierra
- 15 Arranque del motor
- 16 Apagado del motor
- 17 Revisión de la motosierra
- 18 Ajuste del carburador
- 19 Después de completar el trabajo
- 20 Transporte
- 21 Almacenamiento
- 22 Limpieza
- 23 Inspección y mantenimiento
- 24 Guía de solución de problemas
- 25 Especificaciones
- 26 Combinaciones de espadas y cadenas de aserrado
- 27 Piezas y equipos de repuesto
- 28 Eliminación
- 29 Garantía limitada
- 30 Garantía del sistema de control de emisiones
- 31 Marcas comerciales
- 32 Direcciones
0458-787-8621-A
64
English
25 Specifications
24.2 Clearing the Combustion Chamber
WARNING
To reduce the risk of fire and burn injury, use only spark
plugs authorized by STIHL. Always press the spark plug
boot snugly onto the spark plug terminal.
WARNING
To reduce the risk of fire, always move the Master Control
Lever to position before pulling the starter grip if the
spark plug boot has been removed.
If you believe the engine is flooded, you must clear the
combustion chamber before you can start the saw. To clear
the combustion chamber:
► Shut off the engine, @ 16.
► Engage the chain brake, @ 13.1.
► Allow the chain saw to cool down.
► Open the shroud locks (1) by turning them 1/4 turn
counter-clockwise with the combination wrench.
► Remove the shroud (2).
► Remove the spark plug boot (3).
► Unscrew the spark plug and dry it.
► Move the Master Control Lever to position .
► Pull the starter grip and guide it back several times.
The combustion chamber will be cleared.
► Re-insert the spark plug and tighten it down firmly.
► Connect the spark plug boot (3) and press it down firmly.
► Place the shroud in position.
► Tighten the shroud locks until you hear an audible click.
25.1 EPA
The Emission Compliance Period referenced on the
Emissions Compliance Label indicates the number of
operating hours for which the engine has been shown to
meet federal emission requirements.
Category:
A = 300 hours
B = 125 hours
C = 50 hours
25.2 STIHL MS 462 C-M R Rescue Saw
– Displacement: 4.41 cu. in. (72.2 cm³)
– Engine power according to ISO 7293: 5.9 bhp (4.4 kW)
– Idle speed according to ISO 11681: 2,800 ± 50 rpm
– Maximum engine speed: 13,500 rpm
– Recommended spark plugs: NGK CMR6H by STIHL
11
3
0000-GXX-3809-A0
25 Specifications
0000-GXX-5806-A0
3