Instruction Manual
Table Of Contents
- STIHL MSA 120 C, MSA 140 C
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Overview
- 4 Safety Precautions
- 5 Preparing the Saw for Operation
- 6 Charging the Battery, LEDs
- 7 Assembling the Saw
- 8 Engaging and Disengaging the Chain Brake
- 9 Removing and Fitting the Battery
- 10 Switching the Saw On/Off
- 11 Testing the Chain Saw and Battery
- 12 Operating the Saw
- 13 After Finishing Work
- 14 Transporting
- 15 Storing
- 16 Cleaning
- 17 Maintenance
- 18 Repairing
- 19 Troubleshooting
- 20 Specifications
- 21 Bar and Chain Combinations
- 22 Spare Parts and Accessories
- 23 Disposal
- 24 EC Declaration of Conformity
- 25 General Power Tool Safety Warnings
► Wind up the connecting cable and attach it to
the charger.
► Observe the following points when storing the
charger:
–
Charger is out of the reach of children.
–
The charger is clean and dry.
–
Charger is in an enclosed space.
–
Charger is stored separately, away from the
battery.
–
The charger is not suspended from the con‐
necting cable or the holder (3) for the con‐
necting cable.
–
Charger is in a temperature range between
+ 5°C and + 40°C.
16 Cleaning
16.1 Cleaning the chainsaw
► switch off chain saw, engage chain brake and
remove battery
► Clean the chainsaw with a damp cloth or
STIHL resin solvent.
► Clean vents with a paintbrush.
► Remove the chain sprocket cover.
► Clean the area around the chain sprocket with
a damp cloth or STIHL resin solvent.
► Remove foreign objects from the battery com‐
partment and clean the battery compartment
with a damp cloth.
► Clean the electrical contacts in the battery
compartment with a paintbrush or soft brush.
► Fit the chain sprocket cover.
16.2 Cleaning the Bar and Chain
► Switch off the chain saw, engage the chain
brake and remove the battery.
► Remove the bar and chain.
2
0000-GXX-1215-A0
3
3
1
► Clean the oil port (1), oil inlet hole (2) and bar
groove (3) with a soft brush or STIHL resin
solvent.
► Clean the saw chain with a soft brush or
STIHL resin solvent.
► Mount the bar and chain.
16.3 Cleaning the Battery
► Clean the battery with a damp cloth.
16.4 Cleaning the Charger
► Disconnect the mains plug from the power
supply.
► Clean the charger with a damp cloth.
► Clean vents with a paintbrush.
► Clean the charger’s electrical contacts with a
paintbrush or a soft brush.
17 Maintenance
17.1 Deburring the Guide Bar
A burr can build up on the outer edge of the
guide bar.
► Remove burr with a flat file or a STIHL guide
bar dressing tool.
► If you have any queries: Contact your STIHL
servicing dealer.
17.2 Sharpening the Saw Chain
Correctly sharpening saw chains requires a lot of
practice.
STIHL files, STIHL filing aids, STIHL sharpeners
and the brochure “Sharpening STIHL Saw
Chains” help you achieve the right results. To
obtain the brochure visit http://www.stihl.com/
sharpening-brochure.
STIHL recommends you have saw chains
resharpened by a STIHL servicing dealer.
WARNING
■ The chain's cutters are very sharp. There is a
risk of cut injuries.
► Wear work gloves made of durable mate‐
rial.
0000-GXX-1219-A0
► File each cutter with a round file so that the
following points are observed:
–
Round file matches the chain pitch.
–
File from the inside to the outside of the cut‐
ter.
–
Hold the file at right angle to the guide bar.
–
Maintain a filing angle of 30°.
English 16 Cleaning
24 0458-716-0121-D