Instruction Manual
Table Of Contents
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Main Parts
- 4 Safety Symbols on the Products
- 5 IMPORTANT SAFETY INSTRUCTIONS
- 6 Kickback and Other Reactive Forces
- 7 Proper Techniques for Pruning
- 8 Battery Safety
- 9 Maintenance, Repair and Storage
- 10 Before Starting Work
- 11 Charging the Battery
- 12 LED Diagnostics and Acoustic Signals
- 13 STIHL AR Backpack Battery
- 14 Assembling the Chain Saw
- 15 The Chain Brake
- 16 Inserting and Removing the Battery
- 17 Switching the Chain Saw On and Off
- 18 Checking the Chain Saw
- 19 After Finishing Work
- 20 Transporting the Chain Saw and Battery
- 21 Storing the Chain Saw and Battery
- 22 Cleaning
- 23 Inspection and Maintenance
- 24 Troubleshooting Guide
- 25 Specifications
- 26 CSA Standard
- 27 Combinations of Guide Bars and Saw Chains
- 28 Replacement Parts and Equipment
- 29 Disposal
- 1 Préface
- 2 Indications concernant la présente Notice d'emploi
- 3 Principales pièces
- 4 Symboles de sécurité sur les produits
- 5 CONSIGNES DE SÉCURITÉ IMPORTANTES
- 6 Rebond et autres forces réactives
- 7 Techniques appropriées d’élagage
- 8 Sécurité de la batterie
- 9 Maintenance, réparation et rangement
- 10 Avant d'entreprendre le travail
- 11 Recharge de la batterie
- 12 DEL de diagnostic et signaux sonores
- 13 Batterie en sac à dos STIHL AR
- 14 Assemblage de la tronçonneuse
- 15 Le frein de chaîne
- 16 Insertion et retrait de la batterie
- 17 Mise en marche et arrêt de la tronçonneuse
- 18 Contrôle de la tronçonneuse
- 19 Après avoir terminé le travail
- 20 Transport de la tronçonneuse et de la batterie
- 21 Stockage de la tronçonneuse et de la batterie
- 22 Nettoyage
- 23 Inspection et maintenance
- 24 Guide de dépannage
- 25 Spécifications
- 25.1 STIHL MSA 161 T
- 25.2 Pignons
- 25.3 Profondeur de rainure minimale des guide- chaines
- 25.4 Réglage de la jauge de profondeur
- 25.5 Symboles sur la tronçonneuse
- 25.6 Améliorations technologiques
- 25.7 Déclaration de conformité de l'appareil et du chargeur avec la directive CEM (sur la compatibilité électromagnétique)
- 26 Norme CSA
- 27 Combinaisons de guide-chaînes et de chaînes coupantes
- 28 Pièces de rechange et équipement
- 29 Élimination
0458-791-8221-C
47
English
24 Troubleshooting Guide
24.1 Chain Saw and Battery
24 Troubleshooting Guide
Always remove the battery before carrying out any inspection, cleaning or maintenance.
Condition LEDs on
Battery
Possible Cause Remedy
Chain saw does not
start when switched
on.
No electrical contact
between chain saw
and battery.
► Remove the battery, @ 16.2.
► Engage the chain brake, @ 15.1.
► Visually check the electrical contacts in the battery
compartment and on the battery.
► Reinsert the battery, @ 16.1.
1 LED flashes
green.
STIHL AR only:
Additionally,
four long beeps
are emitted.
Battery has low
charge.
► Charge the battery, @ 11.
1 LED glows
red.
Battery too hot / too
cold.
► Allow the battery to warm up or cool down gradually at
ambient temperatures of about 50 °F to 68 °F (10 °C to
20 °C).
4 LEDs flash
red.
STIHL AR only:
Additionally, a
rapid
succession of
short beeps is
emitted.
Malfunction in
battery.
► Remove the battery and reinsert it, @ 16.
► Switch on the chain saw, @ 17.1.
► If the LEDs continue to flash, do not attempt to use.
The battery has a malfunction and must be replaced.
3 LEDs glow
red.
Chain saw too hot. ► Allow the chain saw to cool down.
3 LEDs flash
red.
Malfunction in chain
saw.
► Remove the battery and reinsert it, @ 16
► Switch on the chain saw, @ 17.1.
► If the LEDs still flash, do not attempt to use.
The chain saw has a malfunction and must be checked by
a servicing dealer.