• Operation Revised 12/10/07 www.nationalnail.com CS58 CAP STAPLER OWNER’S MANUAL ! • Maintenance • Safety • Warranty PLEASE READ! This manual contains important information about product safety.
www.nationalnail.
www.nationalnail.com IMPORTANT INFORMATION Please take the time to read and understand the information contained in the Owner’s Manual included with this product before operating or maintaining the STINGER™ CS58 Cap Stapler. Improper use of this tool could result in serious injury or even death. Most accidents occur because of the failure to observe basic safety rules and precautions. Basic safety precautions are outlined in the “Warnings” section of this manual.
www.nationalnail.com WARNINGS ! PERSONAL SAFETY ITEMS • Do not use tool prior to reading the Owner’s Manual. • Always wear eye protection that conforms to ANSI requirements (Z87.1) and provides protection against flying particles both from the front and side. Eye protection should be worn by the operator and by others in the work area. Eye protection is required to protect against flying fasteners and debris that could possibly cause severe eye injury.
www.nationalnail.com WARNINGS AIR SUPPLY AND CONNECTIONS • Use only clean, regulated compressed air as a power source for this tool. Do not use bottle gases, combustible gases or oxygen as a power source for the tool as the tool may explode. • Do not use air supply pressures that exceed 105 PSI. • Do not exceed the recommended maximum operating air pressure as tool wear will be greatly increased. The air supply must be capable of maintaining the operating air pressure of the tool.
www.nationalnail.com WARNINGS OPERATION OF THE TOOL • Never inspect, maintain, repair, adjust, clear a jam or store the tool with the air connected. • Never use the tool in proximity of flammable gases or liquids, as some tools will create sparks that can be an ignition source for a fire or explosion. • Always inspect the safety device for damage and proper operation, prior to operation. • Never assume the tool is empty of fasteners. • Never point the tool toward yourself or any other persons.
www.nationalnail.com TOOL SPECIFICATIONS Operating pressure 95-105 psi Weight 3.9 lb. Nail capacity 200 staples (2-100 count strips) Cap capacity 200 plastic collated caps (1 reel) Air inlet 3/8 NPT Fasteners STINGER StaplePac (National Nail product number 0136360) Consists of 20 strips of 5/8” 20 gauge staples (100 staples per strip) and 10 reels of 1” diameter plastic collated caps (200 caps per reel).
www.nationalnail.com LOADING THE TOOL USE 5/8” STINGER STAPLEPAC CAP STAPLES ONLY • Disconnect air. • Open the magazine cover by pushing the green cover release tab and lifting. • Place cap reel in basket. Make sure the front end of the cap coil is placed over the cap guide area of the basket. Insert lead cap into the feed chute. • Slide caps along the feed chute with fingers until they engage the cap feeder.
www.nationalnail.com OPERATING THE TOOL 1. Do not use tool prior to reading the Owner’s Manual. 2. Read warning label(s) on the tool. 3. Visually inspect the tool for worn or damaged parts. 4. Wear appropriate eye and ear protection. 5. Install a male pneumatic fitting into the end cap of the tool, ensuring that the fitting allows the tool to exhaust any air in the tool when the air hose is disconnected. 6. Add 2 drops of non-detergent, 20-weight oil into the male fitting. 7.
www.nationalnail.com OPERATING THE TOOL 11. Cycle the tool on a scrap work piece to evaluate the depth of penetration by the fastener into the work piece. 12. To adjust the depth of penetration, regulate the air pressure at the regulator and/or disconnect the air hose, adjust the depth control screw, connect the air hose and cycle the tool on a scrap work piece to evaluate the adjustment. 13. Repeat Step 12 as needed to set the correct depth, using the minimum amount of air pressure to drive the fastener.
www.nationalnail.
www.nationalnail.com STINGER CS58 PARTS LIST Item No. Re f No.
www.nationalnail.com STINGER CS58 PARTS LIST Item No. Re f No.
www.nationalnail.com STINGER CS58 PARTS LIST Item No. Re f No.
www.nationalnail.com MAINTANANCE & STORAGE MAINTENANCE 1. Disconnect the air hose from the tool when performing inspections, maintenance or repairs. 2. Use air line lubricators. If lubricators are not available, or if hose lengths exceed 10 feet, add 2 drops of non-detergent 20-weight oil daily into the air inlet of the tool. 3. Whenever repairs or replacement of parts inside the body occur, check the piston “O” ring for adequate grease lubrication. 4.
www.nationalnail.com WARRANTY WARRANTY ITEMS 1. Warranty for cap assemblies, castings and housing castings is one year. 2. Warranty for bumpers, “O” rings, driver blades and piston rings is not applicable as they are normal wearing parts whose life is dependant on application. 3. Warranty for all other parts is 90 days. WARRANTY CONDITIONS 1. The beginning date in which the warranty is in force is the date of purchase. 2. The warranty is not transferable. 3.
www.nationalnail.com TROUBLESHOOTING Disconnect the air hose from the tool when performing inspections, maintenance or repairs. PROBLEM: CORRECTION: 1. Tool operates, but no fasteners are driven. • Check magazine for proper fasteners. Fasteners should slide freely in and out of the magazine. 2. Cap leaks air. • Tighten cap screws. 3. Fasteners jam in nose of tool. • Remove fasteners from magazine. • Open Quick-Clear™ nose (if applicable), remove jammed fastener and close latch. • Load tool. 4.
Visit our website at www.nationalnail.com to learn more about our products and services. 2964 Clydon SW, Grand Rapids MI 49519, USA Phone: 800-968-6245 Fax: 616-531-5970 www.nationalnail.com Contact Inside Sales at 800-746-5659 to place an order for replacement parts.
