Installation Guide

ManualsBrandsStinger ManualsAudioWrangler JK Installation Kit For HEIGH10 Multimedia Head Unit

Stinger HEIGH10

Radio Replacement Kit

for 2011-2018 Jeep Wrangler JK

SR-JK11H

AAMP Global is not a󰀩liated with FCA US LLC. Jeep® is a registered trademark of FCA US LLC. The terms

OEM, Jeep®, Wrangler®, and Gladiator® all terms are used strictly for identication purposes only. It is not

implied that any part listed is a product of, or approved by, Fiat Chrysler Automobiles.

Pacific Accessory Corporation

Page 1

Rev: V2

Date:052521

Introduction and Features

The SR-JK11H is a complete radio replacement kit for Jeep Wrangler JK. All modules and cables are included to retain important

features of the factory system, including: steering wheel-mounted radio controls, factory amplier (if equipped) and AM/FM

reception. Plug & Play wiring harnesses allow for quick and easy installation without the need to cut or splice any wiring.

Important Notes

Recommended Tools

We recommend reading this manual thoroughly to familiarize yourself

with the entire process prior to beginning the installation.

1. Mounting Panel Front Frame

2. HEIGH10 Display Mounting Panel

3. Side Mounting Brackets

4. Top Support Bracket

5. Main Wiring Harness (RP4-JK07-HAR)

6. Radio Replacement Interface Module (RP4-CH11)

7. Satellite Antenna Adapter (SAT-01)

8. AM / FM Antenna Adapter (BAA22)

9. Dual USB Extension (SSUSB2)

Included Components

1. Does not retain the following factory features:

● uConnect

● In Premium Amplied Systems, only two input channels can be used from the aftermarket radio,

therefore there will be no fading capability of the aftermarket stereo.

● SiriusXM Satellite Radio

2. To retain SiriusXM Satellite Radio would require purchasing a SXV300 SiriusXM tuner.

3. Directions for removing the display panel are on page 13.

Plastic Panel Tool

7mm Socket

Ratchet

Ratchet Extension

Phillips Screwdriver

Pick Tool

Flush Cutters

Wire Feeder

NOTE: Along with the SR-JK11H components,

additional hardware and wire harnesses from the

HEIGH10 (UN1810) kit will also be used in the

installation. There is a component list, hardware

guide, wire harness descriptions and illustrations

in the UN1810 Installation Guide for reference.

Summary of content (13 pages)

PAGE 1
SR-JK11H Stinger HEIGH10® Radio Replacement Kit for 2011-2018 Jeep Wrangler JK Introduction and Features The SR-JK11H is a complete radio replacement kit for Jeep Wrangler JK. All modules and cables are included to retain important features of the factory system, including: steering wheel-mounted radio controls, factory amplifier (if equipped) and AM/FM reception. Plug & Play wiring harnesses allow for quick and easy installation without the need to cut or splice any wiring.
PAGE 2
SR-JK11H Stinger HEIGH10® Radio Replacement Kit for 2011-2018 Jeep Wrangler JK Wiring Diagram Overview ® Pacific Accessory Corporation © 2021 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global. AAMP Global is not affiliated with FCA US LLC. Jeep® is a registered trademark of FCA US LLC. The terms OEM, Jeep®, Wrangler®, and Gladiator® all terms are used strictly for identification purposes only.
PAGE 3
SR-JK11H Stinger HEIGH10® Radio Replacement Kit for 2011-2018 Jeep Wrangler JK This installation manual will cover the necessary order of procedures to complete the installation efficiently and to avoid redoing any steps along the way. The order will be as follows; Disassembly, In-Vehicle Harness Connections and Preparation, Display, Radio Module and Harness Preparation, and Radio Unit Installation.
PAGE 4
SR-JK11H Stinger HEIGH10® Radio Replacement Kit for 2011-2018 Jeep Wrangler JK Section 1: Disassembly (cont.) Step 7 Step 8 Step 9 Using the storage tray and area over the gauges, pull the top edge of the panel to release the upper retaining clips. Lower the steering wheel and remove the panel. Remove the four 7mm screws securing the radio and pull the radio from the sub-dash. Disconnect all wire harnesses and antenna cables from the back of the factory radio.
PAGE 5
SR-JK11H Stinger HEIGH10® Radio Replacement Kit for 2011-2018 Jeep Wrangler JK Section 2: In-Vehicle Harness Connections and Preparation (cont.) Part One: Dual USB Extension (SSUSB2) (cont.) Step 4 Step 5 Install the optional USB cover and feed the USB cables through the front of the panel. Secure with the flanged nut and then lock with the lock nut. Reconnect and reinstall the climate control panel. Route the two USB cables up to the radio opening, making sure to route them behind the metal bracket.
PAGE 6
SR-JK11H Stinger HEIGH10® Radio Replacement Kit for 2011-2018 Jeep Wrangler JK Section 2: In-Vehicle Harness Connections and Preparation (cont.) Part Three: AM / FM Antenna Adapter (BAA22) Step 1 Step 2 Connect the BAA22 Antenna Adapter to the factory antenna cable (white connector). Note: The mustard colored antenna cable is for satellite radio. These are the connections for the basic installation.
PAGE 7
SR-JK11H Stinger HEIGH10® Radio Replacement Kit for 2011-2018 Jeep Wrangler JK Section 3: Display, Radio Module and Harness Preparation (cont.) Part Two: Attaching the Radio Module Mounting Brackets FRONT arrow should point towards the Stinger logo. Step 1 Step 2 Step 3 Align and attach one of metal side brackets to the right side of the radio module using two M5 x 10 screws from the HEIGH10 box.
PAGE 8
SR-JK11H Stinger HEIGH10® Radio Replacement Kit for 2011-2018 Jeep Wrangler JK Section 3: Display, Radio Module and Harness Preparation (cont.) Part Three: Main Harness Connections (RP4-JK07-HAR) (cont.) Step 4 Step 5 Step 6 Connect the 16-pin and 6-pin connectors on the RP4-JK07-HAR Main Harness to the HEIGH10 radio module. From the HEIGH10 box, connect the blue LVDS and 8-pin display cables to the radio module.
PAGE 9
SR-JK11H Stinger HEIGH10® Radio Replacement Kit for 2011-2018 Jeep Wrangler JK Section 4: Radio Unit Installation Part Two: Mounting the Radio Assembly Step 1 Step 2 Step 3 With the two display cables routed over the top of the radio module, slide the assembly into place. Take caution that no wiring gets pinched between metal brackets. The top support bracket on the radio assembly needs to go over the top of the factory radio support bracket with the factory nut centered in the bracket cut-out.
PAGE 10
SR-JK11H Stinger HEIGH10® Radio Replacement Kit for 2011-2018 Jeep Wrangler JK Section 4: Radio Unit Installation (cont.) Part Three: Attaching the Display Panel 1/16” 1/16” Step 1 Step 2 Step 3 Apply a piece of cloth tape across the top and bottom edges of the radio opening. Approximately 1/16” of tape along the face of the dash panel and the remainder folded inward. Apply a piece of removable tape across the bottom of the radio opening to protect the dash panel during installation.
PAGE 11
SR-JK11H Stinger HEIGH10® Radio Replacement Kit for 2011-2018 Jeep Wrangler JK Section 4: Radio Unit Installation (cont.) Part Three: Attaching the Display Panel (cont.) 2 3 2 1 1 Step 5 Step 6 To attach the display assembly, align the location ribs on the sides of the mounting panel to the side brackets to center the panel side to side. Holding the mounting panel at the sides: 1. Position the bottom edge almost touching the air vents. 2. Firmly push the assembly against the dash panel. 3.
PAGE 12
SR-JK11H Stinger HEIGH10® Radio Replacement Kit for 2011-2018 Jeep Wrangler JK Section 4: Radio Unit Installation (cont.) Part Three: Attaching the Display Panel (cont.) Step 7 Step 8 Once the display panel is locked into place, use a Phillips screwdriver to tighten the two mount screws on the left and right sides of the mounting panel. Install the front frame by hooking at the top first, then snapping in the sides and bottom. Remove the tape by pulling downward.
PAGE 13
SR-JK11H Stinger HEIGH10® Radio Replacement Kit for 2011-2018 Jeep Wrangler JK Removing the Display Panel Step 1 Step 2 Step 3 Remove the front frame by first releasing the side clips at the locations indicated by arrows. Using a very thin pry tool or similar, carefully release the side clips as shown on both sides. Once the side clips are disengaged, swing the bottom edge upwards to unhook the top of the frame and remove.