Datasheet

ManualsBrandsSTMICROELECTRONICS ManualsLinear ICsLinear IC - Comparator Multi-purpose CMOS, DTL, ECL, MOS, Open collector, TTL SO 14

July 2011 Doc ID 2159 Rev 3 1/19

LM139, LM239, LM339

Low-power quad voltage comparators

Features

■ Wide single supply voltage range or dual

supplies for all devices: +2 to +36 V or ±1 V to

±18 V

■ Very low supply current (1.1 mA) independent

of supply voltage

■ Low input bias current: 25 nA typ

■ Low input offset current: ±5 nA typ

■ Low input offset voltage: ±1 mV typ

■ Input common-mode voltage range includes

ground

■ Low output saturation voltage: 250 mV typ;

SINK

= 4 mA)

■ Differential input voltage range equal to the

supply voltage

■ TTL, DTL, ECL, MOS, CMOS compatible

outputs

Description

This family of devices consists of four

independent precision-voltage comparators with

an offset voltage specification as low as 2 mV

maximum for LM339A, LM239A and LM139A.

Each comparator has been designed specifically

to operate from a single power supply over a wide

range of voltages. Operation from split power

supplies is also possible.

These comparators also have a unique

characteristic in that the input common mode

voltage range includes ground even though

operated from a single power supply voltage.

DIP14

(Plastic package)

SO-14

(Plastic micropackage)

TSSOP14

(Thin shrink small outline package)

QFN16 3x3

(Plastic micropackage)

www.st.com

Summary of content (19 pages)

PAGE 1
LM139, LM239, LM339 Low-power quad voltage comparators Features ■ Wide single supply voltage range or dual supplies for all devices: +2 to +36 V or ±1 V to ±18 V ■ Very low supply current (1.
PAGE 2
Pin and schematic diagram 1 LM139, LM239, LM339 Pin and schematic diagram Figure 1. Pin connections (top view) O utput2 1 14 O utput1 2 13 O utput4 V Figure 2. + CC 3 O utput3 12 V CC Inverting input1 4 11 N on-inverting input4 N on-inverting input1 5 10 Inverting input4 Inverting input2 6 9 N on-inverting input3 N on-inverting input2 7 8 Inverting input3 Schematic diagram (1/4 LM139) VCC 3.5 μ A 100 μA 3.
PAGE 3
LM139, LM239, LM339 2 Absolute maximum ratings and operating conditions Absolute maximum ratings and operating conditions Table 1.
PAGE 4
Absolute maximum ratings and operating conditions Table 2. Operating conditions (Tamb = 25° C) Symbol 4/19 LM139, LM239, LM339 Parameter VCC Supply voltage VICM Common mode input voltage range Toper Operating free-air temperature range – LM139, LM139A – LM239, LM239A – LM339, LM339A Doc ID 2159 Rev 3 Value Unit 2 to 32 ±1 to ±16 V 0 to (VCC+ - 1.
PAGE 5
LM139, LM239, LM339 Electrical characteristics 3 Electrical characteristics Table 3. Electrical characteristics at VCC+ = +5 V, VCC-= GND, Tamb = +25° C (unless otherwise specified) Symbol LM139A - LM239A LM339A Parameter Min. Typ. Max. LM139 - LM239 LM339 Min Typ. Max.
PAGE 6
Electrical characteristics Table 3. Symbol LM139, LM239, LM339 Electrical characteristics at VCC+ = +5 V, VCC-= GND, Tamb = +25° C (unless otherwise specified) (continued) LM139A - LM239A LM339A Parameter Min. trel Large signal response time RL= 5.1 kΩ connected to VCC+, el = TTL, V(ref) = +1.4 V Typ. 300 Max. LM139 - LM239 LM339 Min Typ. Unit Max. 300 ns 1. At output switch point, Vo ≈ 1.4 V, VCC+ from 5 V to 30 V, and over the full common-mode range (0 V to VCC+ -1.5 V). 2.
PAGE 7
LM139, LM239, LM339 Electrical characteristics curves 4 Electrical characteristics curves Figure 3. Supply current vs. supply voltage Figure 4. 80 INPUT CURRENT (nA) Tamb = 0°C 0.8 Tamb= +25°C 0.6 Tamb = +70°C 0.4 Tamb = +125°C 0.2 R = 0 10 20 30 SUPPLY VOLTAGE (V) Figure 5. Output saturation voltage vs.
PAGE 8
Typical applications LM139, LM239, LM339 5 Typical applications Figure 8. Basic comparator Figure 9. Driving CMOS 5V VCC = 5 V 15 kΩ 100 kΩ +V(ref) +V(ref) 1/4 LM139 VO -V(ref) Figure 10. Driving TTL 1/ 4 LM139 & -V(ref) Figure 11. Low frequency op amp 5V 5V 15 kΩ 10 kΩ 1/4 LM139 +V(ref) ~ 1/ 4 LM139 el eo & 0.5 μF 100 kΩ -V(ref) 1 kΩ & Figure 12. Low frequency op amp AV = 100 Figure 13.
PAGE 9
LM139, LM239, LM339 Typical applications Figure 14. Time delay generator VC C = +15 V 10 kΩ 15 kΩ 3 kΩ 200 kΩ 10 MΩ 10 kΩ 1/4 LM139 V3 VCC V03 to t3 3kΩ 10 kΩ to tA 10 kΩ VC1 1/4 LM139 VCC 0 10 MΩ 51 kΩ 1/4 LM139 V2 V(ref.) VCC VO2 to t2 0.001 μF Input gating signal 3 kΩ VCC 10 MΩ 51 kΩ 10 kΩ 1/4 LM139 V3 VC1 V2 V1 0 t 0 t1 t2 t3 V O1 VCC t0 t1 V1 t 51 kΩ t4 Figure 15. Low frequency op amp with offset adjust Figure 16.
PAGE 10
Typical applications LM139, LM239, LM339 Figure 18. Limit comparator VCC 2RS V(ref) high Figure 19. Crystal-controlled oscillator (12 V) 200 kΩ 10 kΩ 2 kΩ 100 kΩ 1/ 4 LM139 VCC Lamp RS eI VCC = 15 V 1/ 4 LM139 0.1 μF 0 eo ~ 2RS 1/ 4 LM139 f = 100 kHz 2N 2222 200 kΩ V(ref) low Figure 20. Zero crossing detector Figure 21. Comparator with a negative reference 15 V 15 V 5.1 kΩ 1/4 LM139 eI 5.
PAGE 11
LM139, LM239, LM339 6 Package information Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark.
PAGE 12
Package information 6.1 LM139, LM239, LM339 DIP14 package information Figure 22. DIP14 package mechanical drawing Table 4. DIP14 package mechanical data Dimensions Millimeters Inches Ref. Min. Typ. A Min. Typ. 5.33 Max. 0.21 A1 0.38 0.015 A2 2.92 3.30 4.95 0.11 0.13 0.19 b 0.36 0.46 0.56 0.014 0.018 0.022 b2 1.14 1.52 1.78 0.04 0.06 0.07 c 0.20 0.25 0.36 0.007 0.009 0.01 D 18.67 19.05 19.69 0.73 0.75 0.77 E 7.62 7.87 8.26 0.30 0.31 0.32 E1 6.10 6.
PAGE 13
LM139, LM239, LM339 6.2 Package information SO-14 package information Figure 23. SO-14 package mechanical drawing Table 5. SO-14 package mechanical data Dimensions Millimeters Inches Ref. Min. Typ. Max. Min. Typ. Max. A 1.35 1.75 0.05 0.068 A1 0.10 0.25 0.004 0.009 A2 1.10 1.65 0.04 0.06 B 0.33 0.51 0.01 0.02 C 0.19 0.25 0.007 0.009 D 8.55 8.75 0.33 0.34 E 3.80 4.0 0.15 0.15 e 1.27 0.05 H 5.80 6.20 0.22 0.24 h 0.25 0.50 0.009 0.02 L 0.40 1.
PAGE 14
Package information 6.3 LM139, LM239, LM339 QFN16 3x3 package information Figure 24.
PAGE 15
LM139, LM239, LM339 Table 6. Package information QFN16 3x3 mm package mechanical data (pitch 0.5 mm) Dimensions Ref. Millimeters Inches Min. Typ. Max. Min. Typ. Max. A 0.80 0.90 1.00 0.031 0.035 0.039 A1 0 0.05 0 A3 0.20 b 0.18 D 2.90 D2 1.50 E 2.90 E2 1.50 e L 3.00 3.00 0.008 0.30 0.007 3.10 0.114 1.80 0.059 3.10 0.114 1.80 0.059 0.50 0.30 0.002 0.012 0.118 0.122 0.071 0.118 0.122 0.071 0.020 0.50 0.012 0.020 Figure 25.
PAGE 16
Package information 6.4 LM139, LM239, LM339 TSSOP14 package information Figure 26. TSSOP14 package mechanical drawing Table 7. TSSOP14 package mechanical data Dimensions Ref. Millimeters Min. Typ. A Max. Min. Typ. 1.20 A1 0.05 A2 0.80 b Max. 0.047 0.15 0.002 0.004 0.006 1.05 0.031 0.039 0.041 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0089 D 4.90 5.00 5.10 0.193 0.197 0.201 E 6.20 6.40 6.60 0.244 0.252 0.260 E1 4.30 4.40 4.50 0.169 0.173 0.
PAGE 17
LM139, LM239, LM339 7 Ordering information Ordering information Table 8.
PAGE 18
Revision history 8 LM139, LM239, LM339 Revision history Table 9. Document revision history Date Revision 01-Mar-2003 1 Initial release. 2 Updated document format. Removed power dissipation from Table 1: Absolute maximum ratings. Added RTHJA, RTHJC, ESD and TLEAD values to Table 1. Updated package information in Chapter 6. Added Table 8: Order codes. 3 Added pin connections for QFN16 package in Figure 1 on page 2. Added thermal information for QFN16 package in Table 1 on page 3.
PAGE 19
LM139, LM239, LM339 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale.