STD25N10F7, STF25N10F7, STP25N10F7 N-channel 100 V, 0.027 Ω typ., 25 A, STripFET™ VII DeepGATE™ Power MOSFET in DPAK, TO-220FP and TO-220 packages Datasheet - production data Features TAB Order codes VDSS RDS(on) max.(1) STD25N10F7 100 V 0.035 Ω 25 A 40 W STF25N10F7 100 V 0.035 Ω 19 A 25 W STP25N10F7 100 V 0.035 Ω 25 A 50 W DPAK TAB ID PTOT 1. @ VGS = 10 V 3 3 2 1 1 TO-220FP 2 TO-220 • Ultra low on-resistance • 100% avalanche tested Applications Figure 1.
Contents STD25N10F7, STF25N10F7, STP25N10F7 Contents 1 Electrical ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.1 Electrical characteristics (curves) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3 Test circuits 4 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
STD25N10F7, STF25N10F7, STP25N10F7 1 Electrical ratings Electrical ratings Table 2. Absolute maximum ratings Value Symbol Parameter Unit DPAK TO-220 TO-220FP VDS Drain-source voltage 100 V VGS Gate-source voltage ± 20 V ID(1) Drain current (continuous) at TC = 25 °C 25 25 19 A ID(1) Drain current (continuous) at TC = 100 °C 18 18 13.
Electrical characteristics 2 STD25N10F7, STF25N10F7, STP25N10F7 Electrical characteristics (TCASE = 25 °C unless otherwise specified) Table 4. On/off states Symbol Parameter Test conditions Min. Typ. Max. Unit - V Drain-source breakdown voltage (VGS= 0) ID = 250 μA IDSS Zero gate voltage drain current (VGS = 0) VDS = 100 V VDS = 100 V; TC = 125 °C 10 100 μA μA IGSS Gate body leakage current (VDS = 0) VGS = ± 20 V ±100 nA VGS(th) Gate threshold voltage VDS = VGS, ID = 250 μA 4.
STD25N10F7, STF25N10F7, STP25N10F7 Electrical characteristics Table 6. Switching times Symbol td(on) tr Parameter Test conditions Turn-on delay time VDD = 50 V, ID = 12.5 A, RG = 4.7 Ω, VGS = 10 V Figure 17 Rise time td(off) tf Turn-off delay time Fall time Min. Typ. Max. Unit - 9.8 - ns - 14 - ns - 14.8 - ns - 4.6 - ns Max. Unit Table 7. Source-drain diode Symbol ISD ISDM (1) VSD(2) Parameter Test conditions Min. Typ.
Electrical characteristics 2.1 STD25N10F7, STF25N10F7, STP25N10F7 Electrical characteristics (curves) Figure 2. Safe operating area for DPAK AM16006v1 ID (A) Figure 3. Thermal impedance for DPAK K Tj=150°C Tc=25°C Single pulse 100 AM16024v1 δ=0.5 0.2 0.1 a is are s n) thi RDS(o in on max i t era by Op ited Lim 10 0.05 0.02 0.01 10 -1 1 100µs 0.01 0.1 1 10 10 -2 10 -6 VDS(V) Figure 4. Safe operating area for TO-220FP 10 -5 10 -4 10-3 10 -1 tp(s) Figure 5.
STD25N10F7, STF25N10F7, STP25N10F7 Electrical characteristics Figure 8. Output characteristics Figure 9. Transfer characteristics AM16008v1 ID (A) VGS=10V 80 AM16009v1 ID (A) 80 9V VDS=6V 70 70 8V 60 60 50 50 7V 40 40 30 30 6V 20 20 10 10 5V 0 0 1 2 3 4 5 6 7 8 0 Figure 10. Gate charge vs gate-source voltage AM16010v1 VGS (V) 12 2 VDS(V) VDD=50V ID=25A 3 4 5 7 6 8 9 10 11 VGS(V) Figure 11. Static drain-source on-resistance AM16011v1 RDS(on) (mΩ) VGS=10V 0.
Electrical characteristics STD25N10F7, STF25N10F7, STP25N10F7 Figure 14. Normalized on-resistance vs temperature AM16014v1 RDS(on) Figure 15. Normalized BVDSS vs temperature AM16015v1 VDS (norm) (norm) ID=250µA ID=12.5A 2 1.04 1.5 1.02 1 1 0.5 0.98 0 -55 -30 -5 20 45 70 95 120 TJ(°C) 0.96 -55 -30 -5 Figure 16. Source-drain diode forward characteristics AM16016v1 VSD (V) 1.1 TJ=-50°C 1 TJ=25°C TJ=150°C 0.9 0.8 0.7 0.
STD25N10F7, STF25N10F7, STP25N10F7 3 Test circuits Test circuits Figure 17. Switching times test circuit for resistive load Figure 18. Gate charge test circuit VDD 12V 47kΩ 1kΩ 100nF 3.3 μF 2200 RL μF IG=CONST VDD VGS 100Ω Vi=20V=VGMAX VD RG 2200 μF D.U.T. D.U.T. VG 2.7kΩ PW 47kΩ 1kΩ PW AM01468v1 Figure 19. Test circuit for inductive load switching and diode recovery times A A AM01469v1 Figure 20. Unclamped inductive load test circuit L A D G D.U.T.
Package mechanical data 4 STD25N10F7, STF25N10F7, STP25N10F7 Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark.
STD25N10F7, STF25N10F7, STP25N10F7 Package mechanical data Table 8. DPAK (TO-252) mechanical data mm Dim. Min. Typ. Max. A 2.20 2.40 A1 0.90 1.10 A2 0.03 0.23 b 0.64 0.90 b4 5.20 5.40 c 0.45 0.60 c2 0.48 0.60 D 6.00 6.20 D1 E 5.10 6.40 6.60 E1 4.70 e 2.28 e1 4.40 4.60 H 9.35 10.10 L 1.00 1.50 (L1) 2.80 L2 0.80 L4 0.60 1.00 R V2 0.
Package mechanical data STD25N10F7, STF25N10F7, STP25N10F7 Figure 23.
STD25N10F7, STF25N10F7, STP25N10F7 Package mechanical data Figure 24. DPAK footprint (a) Footprint_REV_K a.
Package mechanical data STD25N10F7, STF25N10F7, STP25N10F7 Table 9. TO-220FP mechanical data mm Dim. Min. Max. A 4.4 4.6 B 2.5 2.7 D 2.5 2.75 E 0.45 0.7 F 0.75 1 F1 1.15 1.70 F2 1.15 1.70 G 4.95 5.2 G1 2.4 2.7 H 10 10.4 L2 14/21 Typ. 16 L3 28.6 30.6 L4 9.8 10.6 L5 2.9 3.6 L6 15.9 16.4 L7 9 9.3 Dia 3 3.
STD25N10F7, STF25N10F7, STP25N10F7 Package mechanical data Figure 25.
Package mechanical data STD25N10F7, STF25N10F7, STP25N10F7 Table 10. TO-220 type A mechanical data mm Dim. Min. Typ. A 4.40 4.60 b 0.61 0.88 b1 1.14 1.70 c 0.48 0.70 D 15.25 15.75 D1 16/21 Max. 1.27 E 10 10.40 e 2.40 2.70 e1 4.95 5.15 F 1.23 1.32 H1 6.20 6.60 J1 2.40 2.72 L 13 14 L1 3.50 3.93 L20 16.40 L30 28.90 ∅P 3.75 3.85 Q 2.65 2.
STD25N10F7, STF25N10F7, STP25N10F7 Package mechanical data Figure 26.
Packaging mechanical data 5 STD25N10F7, STF25N10F7, STP25N10F7 Packaging mechanical data Table 11. DPAK (TO-252) tape and reel mechanical data Tape Reel mm mm Dim. Dim. Min. Max. A0 6.8 7 A B0 10.4 10.6 B 1.5 12.1 C 12.8 1.6 D 20.2 G 16.4 50 B1 18/21 Min. Max. 330 13.2 D 1.5 D1 1.5 E 1.65 1.85 N F 7.4 7.6 T K0 2.55 2.75 P0 3.9 4.1 Base qty. 2500 P1 7.9 8.1 Bulk qty. 2500 P2 1.9 2.1 R 40 T 0.25 0.35 W 15.7 16.3 DocID025265 Rev 1 18.4 22.
STD25N10F7, STF25N10F7, STP25N10F7 Packaging mechanical data Figure 27. Tape for DPAK (TO-252) 10 pitches cumulative tolerance on tape +/- 0.2 mm T P0 Top cover tape P2 D E F B1 W K0 B0 For machine ref. only including draft and radii concentric around B0 A0 P1 D1 User direction of feed R Bending radius User direction of feed AM08852v1 Figure 28. Reel for DPAK (TO-252) T REEL DIMENSIONS 40mm min.
Revision history 6 STD25N10F7, STF25N10F7, STP25N10F7 Revision history Table 12. Document revision history 20/21 Date Revision 17-Sep-2013 1 Changes First release.
STD25N10F7, STF25N10F7, STP25N10F7 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale.