Datasheet

ManualsBrandsSTMICROELECTRONICS ManualsDiodesDiode Case type TO-220-2

This is information on a product in full production.

October 2013 DocID7688 Rev 7 1/17

STTH8R06

Turbo 2 ultrafast high voltage rectifier

Datasheet - production data

Features

 Ultrafast switching

 Low reverse recovery current

 Low thermal resistance

 Reduces switching losses

 Package insulation voltage:

– TO-220AC Ins: 2500 V rms

– TO-220FPAC: 2000 V DC

Description

The STTH8R06, which uses ST Turbo 2 600 V

technology, is specially suited as boost diode in

continuous mode power factor corrections and

hard switching conditions.

TO-220AC

STTH8R06D

TO-220FPAC

STTH8R06FP

PAK

STTH8R06G

PAK

STTH8R06R

TO-220AC insulated

STTH8R06DIRG

Table 1. Device summary

Symbol Value

F(AV)

8 A

RRM

600 V

(typ) 5.5 A

175 °C

(typ) 1.4 V

(max) 25 ns

www.st.com

Summary of content (17 pages)

PAGE 1
STTH8R06 Turbo 2 ultrafast high voltage rectifier Datasheet - production data Description K K A A TO-220AC STTH8R06D The STTH8R06, which uses ST Turbo 2 600 V technology, is specially suited as boost diode in continuous mode power factor corrections and hard switching conditions. K Table 1. Device summary TO-220FPAC STTH8R06FP K K A A NC D2PAK STTH8R06G K NC I2PAK STTH8R06R K Symbol Value IF(AV) 8A VRRM 600 V IRM (typ) 5.5 A Tj 175 °C VF (typ) 1.
PAGE 2
Characteristics 1 STTH8R06 Characteristics Table 2. Absolute ratings (limiting values) Symbol VRRM Parameter Repetitive peak reverse voltage TO-220AC / TO-220FPAC / IF(RMS) IF(AV) 2 PAK / I PAK Unit 600 V 30 Forward current rms A TO-220AC ins. Average forward current  = 0.5 24 TO-220AC / D2PAK / I2PAK Tc = 130 °C TO-220FPAC Tc = 85 °C TO-220AC ins.
PAGE 3
STTH8R06 Characteristics Table 5. Dynamic characteristics IRM Reverse recovery current 5.5 S factor Softness factor Tj = 125 °C Qrr Reverse recovery charges tfr Forward recovery time VFP IF = 8 A, VR = 400 V, dIF/dt = -200 A/µs 7.2 A 0.3 150 IF = 8 A, dIF/dt = 64 A/µs VFR = 1.1 x VFmax Tj = 25 °C Forward recovery voltage nC Figure 1. Conduction losses versus average current 150 ns 5 V Figure 2. Forward voltage drop versus forward current IFM(A) P(W) 100 24 22 δ = 0.05 20 δ = 0.
PAGE 4
Characteristics STTH8R06 Figure 5. Peak reverse recovery current versus dIF/dt (typical values) Figure 6. Reverse recovery time versus dIF/dt (typical values) trr(ns) IRM(A) 22 120 VR=400V Tj=125°C 20 VR=400V Tj=125°C 110 IF=2 x IF(AV) 100 18 90 IF=IF(AV) 16 80 14 IF=0.5 x IF(AV) 70 12 IF=2 x IF(AV) 60 10 50 IF=0.25 x IF(AV) IF=IF(AV) IF=0.5 x IF(AV) 8 40 6 30 4 20 2 10 dIF/dt(A/µs) 0 dIF/dt(A/µs) 0 0 200 400 600 800 1000 Figure 7.
PAGE 5
STTH8R06 Characteristics Figure 11. Forward recovery time versus dIF/dt (typical values) Figure 12. Junction capacitance versus reverse voltage applied (typical values) tfr(ns) C(pF) 160 100 IF=IF(AV) VFR=1.1 x VF max. Tj=125°C 140 F=1MHz VOSC=30mVRMS Tj=25°C 120 100 80 60 40 20 dIF/dt(A/µs) VR(V) 10 0 0 100 200 300 400 1 500 10 100 1000 Figure 13.
PAGE 6
Package information 2 STTH8R06 Package information  Epoxy meets UL94, V0  Cooling method: by conduction (C)  Recommended torque values: – 0.8 to 1.0 N·m (TO-220FPAC), – 0.4 to 0.6 N·m to (TO-220AC) In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. Figure 14.
PAGE 7
STTH8R06 Package information Table 6. TO-220AC dimension values Dimensions Ref. Millimeters Min. Typ. Inches Max. Min. Typ. Max. A 4.40 4.60 0.173 0.181 C 1.23 1.32 0.048 0.051 D 2.40 2.72 0.094 0.107 E 0.49 0.70 0.019 0.027 F 0.61 0.88 0.024 0.034 F1 1.14 1.70 0.044 0.066 G 4.95 5.15 0.194 0.202 H2 10.00 10.40 0.393 0.409 L2 16.40 typ. 0.645 typ. L4 13.00 14.00 0.511 0.551 L5 2.65 2.95 0.104 0.116 L6 15.25 15.75 0.600 0.620 L7 6.20 6.
PAGE 8
Package information STTH8R06 Figure 15.
PAGE 9
STTH8R06 Package information Table 7. TO-220FPAC dimension values Dimensions Ref. Millimeters Min. Typ. Inches Max. Min. Typ. Max. A 4.4 4.6 0.173 0.181 B 2.5 2.7 0.098 0.106 D 2.5 2.75 0.098 0.108 E 0.45 0.70 0.018 0.027 F 0.75 1 0.030 0.039 F1 1.15 1.70 0.045 0.067 G 4.95 5.20 0.195 0.205 G1 2.4 2.7 0.094 0.106 H 10 10.4 0.393 0.409 L2 16 Typ. 0.63 Typ. L3 28.6 30.6 1.126 1.205 L4 9.8 10.6 0.386 0.417 L6 15.9 16.4 0.626 0.646 L7 9.
PAGE 10
Package information STTH8R06 Figure 16. TO-220AC (NIns. & Ins.
PAGE 11
STTH8R06 Package information Table 8. TO-220AC (NIns. & Ins. 20-up) dimension values Dimensions Ref. Millimeters Min. A Typ. 15.20 a1 Inches Max. Min. 15.90 0.598 3.75 Typ. Max. 0.625 0.147 a2 13.00 14.00 0.511 0.551 B 10.00 10.40 0.393 0.409 b1 0.61 0.88 0.024 0.034 b2 1.23 1.32 0.048 0.051 C 4.40 4.60 0.173 0.181 c1 0.49 0.70 0.019 0.027 c2 2.40 2.72 0.094 0.107 e 4.80 5.40 0.189 0.212 F 6.20 6.60 0.244 0.259 ØI 3.75 3.85 0.147 0.151 I4 15.
PAGE 12
Package information STTH8R06 Devices in I2PAK with nickel-plated back frame must NOT be mounted by frame soldering like SMDs. Such devices are intended to be through-hole mounted ONLY and in no circumstances shall ST be held liable for any lack of performance or damage arising out of soldering of nickel-plated back frames. Figure 17.
PAGE 13
STTH8R06 Package information Table 9. I2PAK dimension values Dimensions Ref. Millimeters Min. Typ. Inches Max. Min. Typ. Max. A 4.40 4.60 0.173 0.181 A1 2.40 2.72 0.094 0.107 b 0.61 0.88 0.024 0.035 b1 1.14 1.70 0.044 0.067 c 0.49 0.70 0.019 0.028 c2 1.23 1.32 0.048 0.052 D 8.95 9.35 0.352 0.368 e 2.40 2.70 0.094 0.106 e1 4.95 5.15 0.195 0.203 E 10 10.40 0.394 0.409 L 13 14 0.512 0.551 L1 3.50 3.93 0.138 0.155 L2 1.27 1.40 0.050 0.
PAGE 14
Package information STTH8R06 Figure 18.
PAGE 15
STTH8R06 Package information Table 10. D2PAK dimension values Dimensions Ref. Millimeters Min. Inches Typ. Max. Min. Typ. Max. A 4.40 4.60 0.173 0.181 A1 2.49 2.69 0.098 0.106 A2 0.03 0.23 0.001 0.009 B 0.70 0.93 0.027 0.037 B2 1.14 1.70 0.045 0.067 C 0.45 0.60 0.017 0.024 C2 1.23 1.36 0.048 0.054 D 8.95 9.35 0.352 0.368 E 10.00 10.40 0.393 0.409 G 4.88 5.28 0.192 0.208 L 15.00 15.85 0.590 0.624 L2 1.27 1.40 0.050 0.055 L3 1.40 1.75 0.
PAGE 16
Ordering information 3 STTH8R06 Ordering information Table 11. Ordering information Order code Marking Package Weight Base qty Delivery mode STTH8R06D STTH8R06D TO-220AC STTH8R06G 4 STTH8R06G 1.90 g 50 Tube 2 1.48 g 50 Tube 2 D PAK STTH8R06G-TR STTH8R06G D PAK 1.48 g 1000 Tape and reel STTH8R06FP STTH8R06FP TO-220FPAC 1.70 g 50 Tube 2 STTH8R06R STTH8R06R I PAK 1.5 g 50 Tube STTH8R06DIRG STTH8R06DI TO-220AC Ins. 1.86 g 50 Tube Revision history Table 12.
PAGE 17
STTH8R06 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale.