Datasheet

ManualsBrandsSTMICROELECTRONICS ManualsPMICsPMIC - ELCs High side PowerSO 10

March 2007 Rev 5 1/16

VN340SP-E

Quad high side smart

Power solid state relay

Features

■ Output current : 0.7A per channel

■ Digital I/O‘s clamped at 32V minimum voltage

■ Shorted load and overtemperature protections

■ Protection against loss of ground

■ Built-in current limiter

■ Undervoltage shut-down

■ Open drain diagnostic output

■ Fast demagnetization of inductive loads

■ Conforms to IEC 61131-2

Description

The VN340SP-E is a monolithic device made

using STMicroelectronics VIPower technology,

intended for driving four indipendent resistive or

inductive loads with one side connected to

ground. Active current limitation avoids dropping

the system power supply in case of shorted load.

Built-in thermal shut-down protects the chip from

overtemperature and short circuit. The open drain

diagnostic output indicates overtemperature

conditions. Each I/O is pulled down when

overtemperature condition of the relative channel

is verified.

Type

demag

(1)

1. Per channel.

DSon

(1)

out

(1)

VN340SP-E

-55V

0.2Ω 0.7A 36V

PowerSO-10

www.st.com

Figure 1. Block diagram

Summary of content (16 pages)

PAGE 1
VN340SP-E Quad high side smart Power solid state relay Features Vdemag(1) RDSon(1) Type VN340SP-E VCC-55V 0.2Ω Iout(1) VCC 0.7A 36V PowerSO-10TM 1. Per channel. ■ Output current : 0.
PAGE 2
VN340SP-E Contents Contents 1 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Pin connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 Test circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
VN340SP-E 1 Maximum ratings Maximum ratings Table 1. Absolute maximum rating Symbol Parameter Value Unit VCC Power supply voltage 45 V -VCC Reverse supply voltage -4 V IOUT Output current (continuos) Internally limited A -6 A IR Reverse output current (per channel) IIN Input current (per channel) ± 10 mA IDIAG Diag pin current ± 10 mA VESD Electrostatic discharge (R = 1.5KΩ; C = 100pF) 2000 V EAS Ptot TJ TSTG Table 2.
PAGE 4
VN340SP-E Pin connections 2 Pin connections Figure 2. Connection diagram (top view) Figure 3.
PAGE 5
VN340SP-E 3 Electrical characteristics Electrical characteristics 10V < VCC < 36V; -40°C < TJ < 125°C; unless otherwise specified Table 3. Symbol Power section Parameter VCC Supply voltage RON On state resistance Test conditions Min Typ 10 IOUT = 0.5A; TJ = 25°C IOUT = 0.5A; TJ = 85°C IOUT = 0.5A; TJ = 125°C IS VOL Vdemag ILGND Table 4. Symbol td(ON) tr td(OFF) tf Table 5. 0.2 0.32 0.4 Ω Ω Ω mA (TJ = 125°C) 6 mA Low state output voltage VIN = VIL; RLOAD >= 10MΩ 1.
PAGE 6
VN340SP-E Electrical characteristics Table 6. Symbol Protection and diagnostic Parameter Test conditions VDIAG(1) Status voltage output low IDIAG = 5mA ( Fault condition ) VSCL(1) Status clamp voltage VUSD Undervoltage shut down ILIM DC Short circuit current IDIAG = 1mA Min 32 IDIAG = 1mA VCC = 24V; RLOAD < 10mΩ Typ Max Unit 1 V 36 -0.7 V V 5 8 V 0.
PAGE 7
VN340SP-E 4 Test circuits Test circuits Figure 4. Avalance energy test circuit Figure 5.
PAGE 8
VN340SP-E Test circuits Figure 6.
PAGE 9
VN340SP-E 5 Switching time waveforms and truth table Switching time waveforms and truth table Figure 7. Switching waveforms Figure 8.
PAGE 10
VN340SP-E Switching time waveforms and truth table Table 7. Truth table MCOUTn I/On OUTPUTn Diagnostic Normal operation L H L H L H H H Overtemperature L H L L L L H L Undervoltage L H L H L L H H Shorted load ( Current limitation ) L H L H L H H H Figure 9.
PAGE 11
VN340SP-E 6 Package mechanical data Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a Lead-free second level interconnect . The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark.
PAGE 12
VN340SP-E Package mechanical data Table 8. PowerSO-10 Mechanical data Mm Inch Dim Min Max Min Typ Max A 3.35 3.65 0.132 0.144 A1 0.00 0.10 0.000 0.004 B 0.40 0.60 0.016 0.024 c 0.23 0.32 0.009 0.012 D 9.40 9.60 0.370 0.378 D1 7.40 7.60 0.291 0.300 E 9.30 9.50 0.366 0.374 E1 7.20 7.40 0.283 0.291 E2 7.20 7.60 0.283 0.300 E3 6.10 6.35 0.240 0.250 E4 5.90 6.10 0.232 e 1.27 0.240 0.050 F 1.25 1.35 0.049 0.053 H 13.80 14.40 0.543 0.
PAGE 13
VN340SP-E Package mechanical data Figure 11. PowerSO-10TM Suggested Pad and Tube Shipment (No Suffix) Figure 12.
PAGE 14
VN340SP-E Order code 7 Table 9.
PAGE 15
VN340SP-E 8 Revision history Revision history Table 10.
PAGE 16
VN340SP-E Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale.