SC118 - Stowaway Slush/Cocktail OWNER’S MANUAL Manual No. 513556 Jan., 2001 Rev.
Need Parts or Service? We stock the parts you need. Our Technicians are factory trained and are certified in the Stoelting Technicare program. CALL Distributor: _________________________ Phone No.: _________________________ (fill in or affix label) Model No.: _______________________ Serial No.
OWNER'S MANUAL FOR MODEL SC118 STOELTING COUNTER MODEL FREEZER This manual provides basic information about the freezer. Instructions and suggestions are given covering its operation and care. The illustrations and specifications are not binding in detail. We reserve the right to make changes to the freezer without notice, and without incurring any obligation to modify or provide new parts for freezers built prior to date of change.
TABLE OF CONTENTS SECTION DESCRIPTION PAGE 1. Introduction ................................................................................................................. 1 2. Installation Instruction 2.1 Safety Precautions ................................................................................................. 2.2 Shipment and Transit.............................................................................................. 2.3 Freezer Installation .......................................
LIST OF ILLUSTRATIONS FIGURE TITLE PAGE 1 Model SC118 .........................................................................................................1 2 Specifications ........................................................................................................ 2 3 Leveling Unit ..........................................................................................................3 4 Power Cord ................................................................................
SECTION 1 INTRODUCTION The Stowaway is a countertop profit machine. This compact unit fits onto any crowded bar, yet its high capacity means it will turn out more than seven gallons every hour. And the Stowaway is as versatile as it is fast, dispensing frozen, pre-mixed or ready-to-serve blends all with the same smooth consistency. Figure 1. Model SC118 Stowaway Features [ Easy plug-in installation. [ Lighted, moving product and front-mounted flavor label attract attention and merchandise product.
Figure 2. Specifications Specifications 12 running amps 115/60/1 15-amp fuse 2.5 gallon (9.5 liter) hopper capacity 5.5 quart (5.
SECTION 2 INSTALLATION INSTRUCTIONS 2.1 SAFETY PRECAUTIONS Do not attempt to operate the freezer until the safety precautions and operating instructions in this manual are read completely and are thoroughly understood. If danger, warning or caution labels are needed, indicate the part number, type of label, location of label, and quantity required along with your address and mail to: Take notice of all warning labels on the freezer.
Figure 4. Power Cord D. Connect the power cord. The plug is designed for 115 volt/15 amp duty. The unit must be connected to a properly grounded receptacle. The electrical cord furnished as part of the freezer has a three prong grounding type plug. The use of an extension cord is not recommended. If one must be used, use one with a size 12 gauge or heavier with a ground wire. Do not use an adaptor to get around grounding requirements. CAUTION DO NOT ALTER OR DEFORM PLUG IN ANY WAY! E.
SECTION 3 INITIAL SETUP AND OPERATION 3.1 OPERATOR'S SAFETY PRECAUTIONS SAFE OPERATION IS NO ACCIDENT; Observe these rules: A. Know the freezer. Read and understand the Operating Instructions. B. Notice all warning labels on the freezer. C. Wear proper clothing. Avoid loose fitting garments, and remove watches, rings or jewelry which could cause a serious accident. D. Maintain a clean work area. Avoid accidents by cleaning up the area and keeping it clean. E. Stay alert at all times.
Figure 7. Front Door and Auger Assembly H. Remove all "O" Rings. To disassemble the freezer, refer to the following steps: WARNING DO NOT USE ANY TYPE OF SHARP OBJECT TO REMOVE THE "O" RINGS. A. Remove the front door by removing the upper and lower plastic shrouds then turn off the knobs, and pull the front door off the studs. B. Remove the spigot body from the spout by pulling the horse shoe clip up and out. Then pull the spigot body out of the spout.
3.4 CLEANING THE FREEZER PARTS Place all loose parts in a pan or container and take to the wash sink for cleaning. To clean freezer parts refer to the following steps: C. Lubricate the drive end of the agitator (rear) shaft with a small amout of white socket lubricant. A small container of socket lubrication is shipped with the freezer. A. Place all parts in warm mild detergent water and clean with brushes provided. Rinse all parts with clean hot water. D.
CAUTION PROLONGED CONTACT OF SANITIZER WITH FREEZER MAY CAUSE CORROSION OF STAINLESS STEEL PARTS. In general, sanitizing may be conducted as follows: A. Prepare 2 gallons (7.5 liters) of sanitizing solution following manufacturer's instructions. B. Pour sanitizer into hopper. C. Place the CLEAN OFF ON switch in the CLEAN position. Check for leaks around the front door seal. D. After five mintues, open spigot to drain sanitizing solution.
SECTION 4 BULB REPLACEMENT 4.1 LIGHT BULB REPLACEMENT 1. Remove the upper plastic shroud. 2. Remove the four retaining screws from the electrical panel and tip forward. 3. Grasp faulty bulb and pull out. 4. Push in replacement bulb until it snaps into place. 5. Replace the electrical panel and secure with the four retaining screws. 6. Replace the plastic shroud. Figure 10.
10
SECTION 5 SEQUENCE OF OPERATIONS 5.1 LIGHTS On/Off light switch is independent of all other switches. When on, the light transformer is operational and the lights illuminate. 5.2 SWITCHES On/Off/Clean Switch Position Mode Switch Position Clean Serve or Standby -Drive Motor and Condenser Fan Motor start and run together, No time limit exists. -Power Transformer, torque switch, compressor, liquid level control, and mix low light are non-operational.
12
SECTION 6 TROUBLESHOOTING PROBLEM: CAUSE CORRECTION High Pressure Cutout Switch Tripped. Dirty condenser. Clean condenser Drive motor overload trips. shuts down when running) Improper Brix reading. Refill with product that has Brix reading between 11 and 13. No mix in product cylinder or low mix in hopper. Keep product cylinder and hopper full. Scraper blade missing from agitator. Replace scraper blade. Freezer is being overdrawn. Slow down rate of draw.
14
15
16
17
18
19
20
21
22
23
24
WARRANTY MIX TRANSFER PUMPS / COCKTAIL / SLUSH 1.
