Warranty

ManualsBrandsStonepoint LED Lighting ManualsLighting & Ceiling Fans1200-Lumens Bronze Outdoor Integrated LED Flood Light with Switch Activation

Switch Control Security Light

Model: 1G1200S-PW/1G1200S-PB

Please read all instructions thoroughly and carefully prior to installing this product. Retain these instructions for future

reference.

Failure to follow these instructions could result in voiding the product warranty. Keystone Group assumes no liability or

responsibility for claims arising from improper installation or improper use.

For questions in regard to the warranty of this product, contact us at 303.652.6164 or email us at info@keystonegroupusa.com

READ FIRST: IMPORTANT SAFETY INSTRUCTIONS

Before you begin installing, servicing, or maintenance of this product, follow these general precautions.

• To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions

and other hazards please read all warnings and instructions included with and on this product prior to installation.

• For commercial installation: service and maintenance of this product should be performed by a qualified, licensed

electrician.

• For residential installation: If you are unsure about the installation or maintenance of this product, consult a

qualified licensed electrician.

o Do not mount the unit against flammable surfaces.

• This product CANNOT be used with a dimmer switch, motion or occupancy sensor or other electronic switching

devices unless otherwise designated. LED products must be powered directly to a switched circuit.

• This product should not be used in areas with limited ventilation or high ambient temperatures.

• This product is intended to be connected to a properly installed and grounded UL listed junction box.

WARNING: RISK OF ELECTRICAL SHOCK

• Turn off electrical power at fuse or circuit breaker box before wiring product to the power supply.

• Verify the supply voltage is correct before installing (110-240V).

• Make all electrical and grounded connections in accordance with the National Electric Code and any applicable local

code requirements.

• All wiring connections should be capped with UL listed wire connectors.

CAUTION: RISK OF PRODUCT DAMAGE

• Never connect components with power on.

• Do not mount or support product in a manner that can cut the outer jacket or damage the wire insulation.

• Avoid covering LED products with insulation, foam or other materials that will prevent convection or conduction

cooling.

• Never connect an LED product directly to dimmer packs, occupancy sensors, timing devices, or other related control

devices, unless individual product specifications deem otherwise.

• Unless individual product deems otherwise; do not exceed product’s maximum temperatures.

• LED products are Polarity Sensitive, ensure proper polarity before installation.

Summary of content (4 pages)

PAGE 1
Switch Control Security Light Model: 1G1200S-PW/1G1200S-PB Please read all instructions thoroughly and carefully prior to installing this product. Retain these instructions for future reference. Failure to follow these instructions could result in voiding the product warranty. Keystone Group assumes no liability or responsibility for claims arising from improper installation or improper use. For questions in regard to the warranty of this product, contact us at 303.652.
PAGE 2
• • Electrostatic Discharge (ESD), can cause damage to LED products. Wear personal grounding equipment during installation and service of the product. Do not touch the individual electronic components, it may cause ESD (Electronic Discharge), shorten lamp life or alter performance. CAUTION: RISK OF INJURY • • • Wear gloves and safety glasses at all times when removing fixture from carton, installing or servicing the product. Avoid direct eye exposure to the light source while it is on.
PAGE 3
MOUNTING AND WIRING THE LIGHT NOTE: DO NOT MOUNT ON THE GROUND, RECOMMENDED INSTALLATION HEIGHT IS 6 ½ FEET TO 10 FEET 1. 2. 3. 4. 5. 6. 7. Turn off power to the circuit breaker box. DO NOT rely on only the switch power being turned off. Install the cross bar (E) to the junction box and secure with the (2) mounting screws (I). If installing to a wall or building, pre-drill holes and use appropriate masonry plugs, now install the cross bar to the surface using the (2) mounting screws (F).
PAGE 4
ADJUSTING YOUR LIGHT HEADS Your light heads can be adjusted by turning the individual light head to desired position. You can also adjust your light head up and down to your desired position. TROUBLE SHOOTING If the light does not come on: ➢ Verify the power is turned on at the switch and breaker ➢ Verify that the product is properly wired ➢ Verify that the line voltage is correct (110-240V) PRODUCT MAINTENANCE To clean the surface of the light, use mild soap and water.