TDS

TECHNICAL DATA
SRT-44
STOPS RUST
®
WITH TURBO SPRAY SYSTEM
1
Form: ARJ-1639
Rev.: 051618
DESCRIPTION AND USES
Rust-Oleum
®
Stops Rust
®
Innovative Turbo Spray System
delivers the same trusted protection of traditional Stops Rust
and now gets the job done 4x faster. Super tall fan spray
coats the surface in fewer passes for faster projects.
Professional spray equipment results without messy
cleanup. 24 ounce can optimized for large jobs. Fun and
exciting for users to tackle large, intimidating jobs in minutes.
Rust-Oleum Stops Rust Enamel Sprays are designed to
provide a durable protective coating with excellent rust
prevention, and excellent resistance to abrasion, fading,
chipping, and dulling. These sprays apply easily, provide
excellent coverage and dry fast to a tough attractive finish.
Rust-Oleum Stops Rust Enamel Sprays are ideal for ferrous,
non-ferrous metal and wood surfaces. It features a comfort
tip with a wider finger pad to reduce fatigue caused by
continuous spraying and an any-angle tip which allows you
to spray at any angle. Not for use on galvanized metal.
PRODUCTS
SKU
DESCRIPTION (Aerosol)
334128
Gloss Black
334133
Gloss White
PRODUCT APPLICATION
READ ALL INSTRUCTIONS CAREFULLY BEFORE
STARTING PROJECT
Use outdoors or in a well-ventilated area such as an open
garage. Use when temperature is between 50°-90°F (10°-
32°C) and humidity is below 70% to ensure proper drying.
Do not apply to surfaces that, when heated, exceed 200°F
(93°C) or galvanized metal. Avoid spraying in very windy,
dusty conditions. Cover surrounding area to protect from
spray mist.
SURFACE PREPARATION
Remove all dirt, grease, oil, salt and chemical contaminants
by washing the surface with a commercial detergent, or
other suitable cleaning method. Rinse with fresh water and
allow to thoroughly dry. Remove loose paint and rust with a
wire brush or sandpaper. Previously coated surfaces must
be sound and in good condition. Smooth, hard, or glossy
finishes should be scarified by sanding to create a surface
profile.
PRODUCT APPLICATION (cont.)
SURFACE PREPARATION (cont.)
WARNING! If you scrape, sand or remove old paint from any
surface, you may release lead paint dust. LEAD IS TOXIC.
EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS
ILLNESS, SUCH AS BRAIN DAMAGE; ESPECIALLY IN
CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID
EXPOSURE. Wear a NIOSH approved respirator to control
lead exposure. Clean up carefully with a HEPA vacuum and
a wet mop. Before you start, find out how to protect yourself
and your family by contacting the National Lead Information
Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.
PRIMING
Use of a Stops Rust
®
Primer provides added corrosion
protection, superior adhesion and hiding and is especially
recommended for bare wood and metal.
APPLICATION
Shake can vigorously for one minute after mixing ball begins
to rattle. If mixing ball fails to rattle DO NOT STRIKE CAN.
Contact Rust-Oleum. Shake often during use. Hold can
upright 18-24" from surface and spray in a steady back-and-
forth motion, slightly overlapping each stroke. Keep the can
the same distance from the surface. Keep the can in motion
while spraying. It is recommended to apply a light first coat,
target 50% coverage. Apply 2 or more light coats a few
minutes apart.
DRY AND RECOAT TIMES
Based on 70°F (21°C) 50% relative humidity. Allow more
time at cooler temperatures. Dries tack-free in 2-4 hours, to
handle in 5-9 hours, and is fully dry in 24 hours. Apply a
second coat within 1 hour or after 48 hours.
CLEAN UP
Wipe off tip before storing. Clean up wet paint with Xylene
or mineral spirits. Throw away empty can in trash pickup.
Do not burn or place in home trash compactor.
CLOGGING
If valve clogs, twist and pull off spray tip and rinse it in a
solvent such as mineral spirits. Do not stick a pin or other
objects into the stem.