StorCase® Technology Data Express® DE110 Removable Ultra ATA133 Drive Enclosure User's Guide
i StorCase® Technology Data Express® DE110 Removable Ultra ATA133 Drive Enclosure User's Guide Part No. D89-0000-0158 C03 October 2005 StorCase Technology, Inc. 17600 Newhope Street Fountain Valley, CA 92708-9885 Phone (714) 438-1850 Fax (714) 438-1847 PATA DE110 User's Guide - Rev. C03 StorCase Technology, Inc.
ii LIMITED WARRANTY STORCASE TECHNOLOGY, Incorporated (StorCase) warrants that its products will be free from defects in material and workmanship, subject to the conditions and limitations set forth below. StorCase will, at its option, either repair or replace any part of its product that proves defective by reason of improper workmanship or materials.
iii Warranty Claim Requirements To obtain warranty service, the defective product must be returned to your local authorized StorCase dealer or distributor, or, with prior StorCase approval, to the StorCase factory service center. For defective products returned directly to StorCase, a Return Material Authorization (RMA) number must be obtained by calling StorCase Customer Service at (714) 445-3455. The RMA number must be prominently displayed on the outside of the return package.
iv Declaration of Conformity Company Name: StorCase Technology, Inc.
v Table of Contents INTRODUCTION ........................................................................................................................ Packaging Information ................................................................................................... Serial Numbers ............................................................................................................... Package Contents ...........................................................................................
vi List of Figures Figure 1: Figure 2: Figure 3A: Figure 3B: Figure 4: Figure 5: Figure 6: Figure 7: Figure 8: Figure 9: Package Contents .............................................................................................. 2 DE110 Receiving Frame and Carrier ................................................................. 3 Receiving Frame Front Panel ............................................................................. 4 Receiving Frame Unit ID Number and Activity Display ............
Introduction 1 INTRODUCTION Packaging Information The StorCase Technology Data Express® system is shipped in a container designed to provide protection and prevent damage during shipment. The Data Express unit was carefully inspected before and during the packing procedure at the factory. Bent or broken connectors, or evidence of other damage to the Data Express should be reported to the shipper immediately. Refer to Figure 1 for the package contents.
2 Introduction Package Contents The DE110 package contents include the following items. If any item is missing or damaged, contact your StorCase dealer for a replacement. 2 0834a 1 5 4 7 6 3 8 Da Disk (Not Drive Inclu ded) I/O ID Drive Carr Sele ier Pow er Cabl Cabl ct Cabl e ta E xpre ss Cabl Cove (Prov r e ided) e e Drive Hard Philli 3/16 ps wareMounting Flat # 6-32(4ea HD x ) 0151 Cabl Scre e # Flat 6-32 ws (2Cove HD x 3/16plcs)r Carrier & Rec. Frame Carrier Only 1.
Introduction 3 General Description NOTE: For Ultra ATA133 (133MByte/sec) operation, an Ultra ATA133 controller and hard drive(s), and appropriate 40-pin, 80-conductor cable are required. The StorCase Technology Data Express® DE110 is a removable drive carrier and receiving frame, designed to provide durable and reliable mounting for one (1) low-profile (up to 1" high) 3.5" Ultra ATA133 drive within a 5.25" half-height peripheral slot (Figure 2).
4 Introduction Receiving Frame Front Panel (Figures 3A & 3B) Unit ID Number Indicator (Figures 3A & 3B) - This LED displays the physical address of the DE110 device carrier if the carrier is Installed and Locked in the receiving frame or if the carrier is removed from the receiving frame. If the carrier is Installed but not Locked in the receiving frame, a "u" will be displayed to indicate an unlocked condition.
Introduction 5 Figure 3B: Receiving Frame Unit ID Number and Activity Display Drive Carrier (Figure 4) Key Lock/Drive Power Switch (Figure 4) - Performs three functions. The key switch assures proper seating of the drive carrier within the receiving frame, turns power to the drive carrier ON and OFF, and prevents unauthorized removal or installation of the carrier. For the computer to access data on the disk drive, the key must be turned counterclockwise to the locked position.
6 Introduction Receiving Frame Rear Panel (Figure 5) I/O Connector (JP1) - The input/output connector provides a standard interface for all IDE signals (Figure 5). DC Power Connector (P1) - A standard 4-pin DC power connector is used to accept DC power. Option Pins (W1) Master/Slave Selection Jumper (ID0 & ID1) - Master Drive designation (jumper is factory-installed on ID0). Change jumper position to Pins 3 & 4 (ID1) for Slave Drive designation.
Installation 7 INSTALLATION NOTES: A #2 Phillips screwdriver will be required during this procedure. Since specifications (specifically, pin assignments) between drive manufacturers may vary, please refer to your drive manufacturer's documentation for exact information regarding Master/Slave and Cable Select configuration. Preparation While performing the steps in this section, work on a soft surface to prevent excessive shock to the drive being installed.
8 Installation Installing the Drive into the Carrier 1. Attach the DC power cable (from the Drive Carrier Board) to the drive (Figure 6). 2. Carefully insert the drive into the carrier. Slide the drive towards the Drive Carrier Board, so that the I/O connector on the drive mates with the connector on the Drive Carrier Board (Figure 6). Make sure that the DC power cable is not pinched. Turn the drive/carrier assembly over. 3. Fasten the drive into place with four (4) #6-32 Phillips F.H.
Installation 9 1 Insert this end into the carrier first 2 Slide the cover towards the back of the carrier 3 Secure with #6-32 Phillips Flat Hd. screws (2 Total) 0836 Figure 7: Drive Cover Installation Installing the Receiving Frame NOTE: Use a #2 Phillips screwdriver for this procedure. The drive should be installed into the carrier before installing the receiving frame into the mounting bay of a computer or expansion chassis. 1. Turn OFF power to the computer. 2.
10 Installation 4. Adjust the front of the receiving frame so the carrier slides freely in and out on the receiving frame guides. The position of adjoining peripheral units may require adjustment. Front of Unit Mounting Holes (Left) Mounting Holes (Right) 0837 Mounting Holes (Bottom) Figure 8A: Receiving Frame Mounting Holes StorCase Technology, Inc. PATA DE110 User's Guide - Rev.
Installation 11 Spacer Plates (Optional) NOTE: Depending on the computer system, spacer plates may be positioned on the receiving frame to utilize either top or bottom row of side-mounting holes (Figure 8B). The DE110 is designed to fit most computer systems with standard 5.25" peripheral slots. The installation of the spacer plates (provided) may or may not be necessary. Spacer Plate (2 Total) OR 0869 Figure 8B: Spacer Plate Installation (Optional) 5.
12 Installation 8. Reconnect any system or peripheral cables removed earlier. 9. Turn ON power to the computer. If the installation has been successful, and all the cables have been properly attached, the system should boot normally. Although the computer may not recognize the DE110 yet, the front panel display on the DE110 receiving frame should illuminate. 10. The new drive may need to be formatted or initialized prior to use with the operating system and applications software.
Installation 13 Unit ID Select Rotating Switch Drive Carrier Guide 0087a Typical Data Express Receiving Frame Figure 9: Unit ID Select Switch Location Unit ID Select Switch Settings The following table lists the Unit ID Select Switch settings and the valid AT/IDE unit numbers. Please note that all invalid switch settings have X's through them and result in a blank display in the receiving frame display window.
14 Installation I/O Connector JP1 The I/O connector (JP1) pin assignments are as follows: Table 2: AT/IDE Interface Signals Pin 01 03 05 07 09 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 Signal Host ResetHost Data 7 Host Data 6 Host Data 5 Host Data 4 Host Data 3 Host Data 2 Host Data 1 Host Data 0 Ground DMARQ DIOWDIORReserved Reserved IRQ 14 Host ADDR 1 Host ADDR 0 Host CS0DASP- I/O O I/O I/O I/O I/O I/O I/O I/O I/O O O O I O O O Notes Pin 02 04 06 08 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 4
Appendix A - Specifications/Dimensions 15 APPENDICES PATA DE110 User's Guide - Rev. C03 StorCase Technology, Inc.
16 Appendix A - Specifications/Dimensions Appendix A - Specifications/Dimensions Environmental Specifications Operating Storage Ambient Temperature Relative Humidity (1) 0° C to 50° C 10% to 80% Altitude -1000 to 10,000 ft -305m to 3048m -40° C to 70° C 10% to 90% -1000 to 40,000 ft -305m to 12195m Shock 10g 60g (2) (1) Non-condensing with maximum gradient of 10% per hour. (2) 11 msec pulse width 1/2 sine wave. Physical Specifications (1) Carrier Receiving Frame Height 1.52 (38.
Appendix A - Specifications/Dimensions Receiving Frame with Carrier Installed 17 2.06 (52.3mm) 3.12 (79.2mm) 1.61 (40.9mm) 0.47 (11.9mm) 5.81 (147.6mm) 8.657 (219.89mm) 3.12 (79.2mm) Carrier Only 1.52 (38.6mm) 4.73 (120.1mm) 7.939 (201.65mm) 3.75 (95.3mm) 0838C 4.081 (103.66mm) 1.75 (44.5mm) Figure A-1: DE110 Physical Dimensions (Dimensions are for reference only) PATA DE110 User's Guide - Rev. C03 StorCase Technology, Inc.
18 Appendix B - Optional Accessories Appendix B - Optional Accessories Carrying Case 320FW_13 Figure B-1: Carrying Case The optional molded plastic carrying case (P/N S20E101) is designed to transport one (1) DE110 carrier from one site to another in a safe, impact and moisture-resistant environment. Its compact dimensions, 10 long x 11 wide x 4.5 high, make it easy to carry and to store. The foam lining is contoured to fit a single Data Express carrier.
Reader's Comments 19 Reader's Comments Please take a few moments when your computer system is up and running to send us your ideas and suggestions for improving our products and documentation.
Reader's Comments CUT ALONG THIS LINE FROM BOTTOM TO TOP OF PAGE 20 FOLD ALONG THIS LINE AND STAPLE SHUT NO POSTAGE NECESSARY IF MAILED IN THE UNITED STATES B U S I N E S S R E P LY M A I L FIRST CLASS MAIL PERMIT NO. 10686 SANTA ANA, CA POSTAGE WILL BE PAID BY ADDRESSEE TECHNOLOGY CORPORATION 17600 NEWHOPE STREET FOUNTAIN VALLEY CA 92708-9885 StorCase Technology, Inc. PATA DE110 User's Guide - Rev.
