User's Manual

User Manual

Connect the Wii Remote with the receiver and the Wii Remote with the Console,

also connect the receiver with the Wii Nunchuk and installed the battery according to

the instructions.At this time the transmitter will be in sleep mode, press the comb key

to wake up transmitter, the transmitter into the search mode, Status LED flashes to 2

Hz, and then wait for the receiver to connect with the transmitter, if any receiver is in

connection mode, transmitter and the receiver will be reset identification ID and

confirmed to use of other channel connection (registration), After the wireless

Transmitter is connected it will register with the receiver ,and the transmitter Status

LED flashes with the 1hz. Transmitter and receiver will turn into data transfer mode.

With the transmitter press the Comb Key to awaken the transmitter, the transmitter

then will go into the search mode , the transmitter status LED will flash 2 Hz.When

the receiver is in the search mode, the receiver connection led will flash 2 Hz.

ＦＣＣ　ＮＯＴＥ：Ｔｈｉｓ　ｄｅｖｉｃｅ　ｃｏｍｐｌｉｅｓ　ｗｉｔｈ　Ｐａｒｔ　１５　ｏｆ　ｔｈｅ　ＦＣＣ　Ｒｕｌｅｓ．　Ｏｐｅｒａｔｉｏｎ　ｉｓ　

ｓｕｂｊｅｃｔ　ｔｏ　ｔｈｅ　ｆｏｌｌｏｗｉｎｇ　ｔｗｏ　ｃｏｎｄｉｔｉｏｎｓ：（１）ｔｈｉｓ　ｄｅｖｉｃｅ　ｍａｙ　ｎｏｔ　ｃａｕｓｅ　ｈａｒｍｆｕｌ　

ｉｎｔｅｒｆｅｒｅｎｃｅ，　ａｎｄ　（２）　ｔｈｉｓ　ｄｅｖｉｃｅ　ｍｕｓｔ　ａｃｃｅｐｔ　ａｎｙ　ｉｎｔｅｒｆｅｒｅｎｃｅ　ｒｅｃｅｉｖｅｄ，　

ｉｎｃｌｕｄｉｎｇ　ｉｎｔｅｒｆｅｒｅｎｃｅ　ｔｈａｔ　ｍａｙ　ｃａｕｓｅ　ｕｎｄｅｓｉｒｅｄ　ｏｐｅｒａｔｉｏｎ．



Ｔｈｅ　ｍａｎｕｆａｃｔｕｒｅｒ　ｉｓ　ｎｏｔ　ｒｅｓｐｏｎｓｉｂｌｅ　ｆｏｒ　ａｎｙ　ｒａｄｉｏ　ｏｒ　ＴＶ　ｉｎｔｅｒｆｅｒｅｎｃｅ　ｃａｕｓｅｄ　ｂｙ　

ｕｎａｕｔｈｏｒｉｚｅｄ　ｍｏｄｉｆｉｃａｔｉｏｎｓ　ｔｏ　ｔｈｉｓ　ｅｑｕｉｐｍｅｎｔ．　Ｓｕｃｈ　ｍｏｄｉｆｉｃａｔｉｏｎｓ　ｃｏｕｌｄ　ｖｏｉｄ　ｔｈｅ　

ｕｓｅｒ＇ｓ　ａｕｔｈｏｒｉｔｙ　ｔｏ　ｏｐｅｒａｔｅ　ｔｈｅ　ｅｑｕｉｐｍｅｎｔ．

PAGE 1
User Manual Connect the Wii Remote with the receiver and the Wii Remote with the Console, also connect the receiver with the Wii Nunchuk and installed the battery according to the instructions.
PAGE 2
6.1.3 Wireless receiver and transmitter complete re-configuration identification ID and confirmed the completion channel connecting lines. 5.2 Connection status： 5.2.1 Online status of the Transmitter break the connection： When the receiver and the Transmitter has been in connection line status, if connection is cut, the Transmitter will return into the search mode, Connection LED will flash with 1 Hz, Transmitter connected or press comb key again, the receiver and the transmitter can be connected again.
PAGE 3
When the receiver and the transmitter has been in connection status, Press Comb key for 4 seconds , the transmitter will go into the search mode, the transmitter Status LED flashes to 2 Hz, and the original receiver interrupted, the receiver will go to the connected Line mode, the receiving end of the Status LED flashes to 1 Hz.
PAGE 4
Configuration appearance parameter Transmitter part Receiver part