Installation Guide

ManualsBrandsStorm System ManualsPaintCategory 2 1-gal. Angel Street Exterior Semi-Transparent Dual Dispersion Wood Finish

Product Description:

This product was developed to provide exterior protection without detracting from the texture and graining of natural

wood. Two coats are recommended for maximum protection on most new or unfinished woods. A single coat is

recommended for porches, railings and outdoor furniture.

Precautions:

DO NOT use over previously painted, solid stained or varnished surfaces. Temperatures of both air and surface should

be at least 50°F (10°C) during application and drying time. Do not apply in hot sunlight or if wet weather is expected

within 48 hours. Surfaces are slippery when wet. Use caution when walking on wet surfaces during application. Do not

mix with oil, water or other types of paint or stain. All loose surface wood fibers must be completely removed. Storm

System stains provide maximum resistance to fading and mildew.

Architectural Specifications:

•Unfinished Wood Decks, Siding, Rails, Posts, Fences, Patios, Screening and Outdoor Furniture;

1 Coat Storm System Dual Dispersion Semi-Transparent Finish #225 Series

•Previously Stained Surfaces (after proper preparation);

1 Coat Storm System Dual Dispersion Semi-Transparent Finish #225 Series

•Pressure Treated Wood;

1 Coat Storm System Dual Dispersion Semi-Transparent Finish #225 Series

Note: New pressure treated wood must be thoroughly scrubbed with a solution of Tri-sodium phosphate and water,

rinsed clean and allowed to dry completely before finishing. Do not use interchangeably on the same substrate with

other Storm System products as you may note differences in appearance. Appearance varies with different species of

wood. Samples should be tested on the actual wood being used to insure an acceptable appearance.

Application:

WARNING! If you scrape, sand or remove old paint from any surface, you may release lead dust. LEAD IS TOXIC.

EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN

CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to

control lead exposure. Carefully clean up with a wet mop or HEPA vacuum. Before you start, find out how to protect

yourself and your family by contacting the U.S. EPA/Lead Information Hotline at 1-800-424-LEAD (5323) or log on to

www.epa.gov/lead.

This product is of proper consistency as packaged is to be applied without thinning under normal environmental

application conditions.

Surface Preparation:

All surfaces must be clean and thoroughly dry before application of this product. All mildewed areas should be

scrubbed clean with an appropriate mildew killing solution and thoroughly rinsed. Apply to rough side of clapboards for

best results.

Application:

Stir thoroughly. Additional light stirring during application may be necessary to maintain color uniformity. This product

is of proper consistency as packaged, to be applied without thinning under normal environmental and application

conditions. Clean tools and equipment as soon as possible with soap and water. Apply with synthetic brush, roller or

spray. Avoid overlapping. Product colors may vary with the type of wood. A small board of an inconspicuous section of

the house should be applied first to test the product on the actual wood. This product is self-priming on wood surfaces.

Cedar, Redwood, Cypress and some other woods contain a natural water soluble ingredient, “tannin,” that will show as

a reddish brown stain when it migrates to the wood surface. If these stains appear, they may be removed by washing

with a mild detergent solution and rinsing with clear water.

Recommended Use:

Shingles / Shakes / Clapboards / Beams / Plywood Siding / Trim / Decks

Safety Information:

Avoid contact with skin. Use only with adequate ventilation. Keep out of reach of children. Protect from freezing. Do not

take internally. Close container after each use.

First Aid: If swallowed, do not induce vomiting. Call a physician immediately.

Dual Dispersion Semi-Transparent

Clear Base No. 225 Series

4/10/2017

STORM SYSTEM™

California Paints ▪ 150 Dascomb Rd. ▪ Andover, MA ▪ 01810 ▪ www.stormsystem.com ▪ 800-225-1141

5/17/2013

Exterior

Type:

Acrylic/Alkyd Dispersion

Specular Gloss:

Volume Solids:

23.0

@ 60°

Solids by Weight:

30.1

Dry Film Thickness:

1.0

mils

Vehicle:

90.1

Pigment:

9.9

Viscosity @ 77 °F:

Maximum VOC:

100

g/liter

Flash Pt °F:

Non-combustible

Thinner:

Water

Product Specifications:

Exposure:

Exterior

(Weight Per Gallon:

9.2

Available Package Sizes:

To Handle:

To Recoat:

hrs.

To Touch:

Drying Times:

lbs. ± .5 lb)

Surface Spread Rate:

s.f./gal.

(Spray Application is 50% of above)

Tools and Equipment:

Smooth:

200-400

Porous:

150-350

s.f./gal.

Brush -

Natural Bristle

Roller -

Medium Nap

Airless Spray -

.011 to .013

±2

±5

(@ 70-77 °F, 50% R.H.)

Soap & Water

Clean Up:

Available Colors and Bases:

Gallon 5 Gallon

See back page

for complete list

Summary of content (2 pages)

PAGE 1
5/17/2013 STORM SYSTEM™ Exterior 4/10/2017 Dual Dispersion Semi-Transparent Clear Base No. 225 Series Product Description: This product was developed to provide exterior protection without detracting from the texture and graining of natural wood. Two coats are recommended for maximum protection on most new or unfinished woods. A single coat is recommended for porches, railings and outdoor furniture.
PAGE 2
5/17/2013 STORM SYSTEM™ 4/10/2017 Exterior Dual Dispersion Semi-Transparent Clear Base No. 225 Series Product Description: Product Specifications: This product was developed to provide exterior protection without detracting from the texture and graining of natural wood. Two coats are recommended for maximum protection on most unfinished woods. A single coat is ITEM # new or COLOR NAME recommended for porches, railings and outdoor furniture.