Installation Guide

ITEM # COLOR NAME
34595XX-1 Clear Base
345C103-1 Bound Rock
345C104-1 Butternut
345C105-1 Cedar
345C106-1 Cedar Mill
345C107-1 Cedar Walk
345C108-1 Chestnut Brown
345C109-1 Country Club
345C110-1 Earthlink
345C111-1 Headwall
345C112-1 Marshview
345C113-1 Morado
345C114-1 Mystic Gray
345C115-1 Natural
345C116-1 Natural Light
345C117-1 Natural Oak
345C118-1 Nature Trail
345C119-1 Parsons Gray
345C120-1 Redwood
345C121-1 Reections
345C122-1 Seacoast Gray
345C123-1 Seasalt Gray
345C124-1 Teak
345C125-1 Tenderfoot
345C126-1 Treeline
Product Description:
This product decorates and protects exterior wood from weather and temperature changes. This product can be used
on new wood, previously stained wood and new pressure treaded wood with proper preparation. Apply one coat over
previously stain surfaces but two coats will provide maximum protection on new or unfinished wood.
Precautions:
DO NOT use over previously painted, solid stained or varnished surfaces. Temperatures of both air and surface should
be at least 50°F (10°C) during application and drying time. Do not apply in hot sunlight or if wet weather is expected
within 48 hours. Surfaces are slippery when wet. Use caution when walking on wet surfaces during application.
Architectural Specifications:
•Unfinished Wood Decks, Siding, Rails, Posts, Fences, Patios, Screening and Outdoor Furniture;
1 Coat Storm System Dual Dispersion Semi-Solid Finish #345 Series
•Previously Stained Surfaces (after proper preparation);
1 Coat Storm System Dual Dispersion Semi-Solid Finish #345 Series
•Pressure treated wood;
1 Coat Storm System Dual Dispersion Semi-Solid Finish #345 Series
Note: New pressure treated wood must be thoroughly cleaned with Storm System All Surface Cleaner, rinsed clean
and allowed to dry completely before finishing. Do not use interchangeably on the same substrate with other Storm
System products as you may note differences in appearance. Appearance varies with different species of wood.
Samples should be tested on the actual wood being used to insure an acceptable appearance.
Application:
WARNING! If you scrape, sand or remove old paint from any surface, you may release lead dust. LEAD IS TOXIC.
EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN
CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to
control lead exposure. Carefully clean up with a wet mop or HEPA vacuum. Before you start, find out how to protect
yourself and your family by contacting the U.S. EPA/Lead Information Hotline at 1-800-424-LEAD (5323) or log on to
www.epa.gov/lead.
This product is of proper consistency as packaged is to be applied without thinning under normal environmental
application conditions.
Surface Preparation:
Surfaces must be thoroughly dry to allow penetration. Surfaces must be clean and free from all other coatings that
may prevent penetration. Always test a small area before application to the entire surface. All mildewed areas should
be cleaned with Storm System All Surface Mold & Mildew Stain Remover. New pressure treated wood should be
scrubbed with Storm System All Surface Cleaner to remove all surface deposits. Rinse thoroughly and allow to dry.
Application:
Stir thoroughly. The clear base can be tinted up to 8 oz. per gallon with Universal Colorants. This product can be
applied by synthetic brush, roller or spray. Clean brushes and equipment with soap and water and remove spatters
immediately after completion of job. NOTE: for decks, use Storm System CATEGORY 1 100% Acrylic Top Coat
#11550 for longer life and greater durability.
Recommended Use:
For Pressure Treated and Conventional Woods / Sun Decks / Wood Screening / Patios / Siding / Fencing / Benches /
Open Porches / Outdoor Furniture / Railings and Posts / Wood Pool and Garden Enclosures
Safety Information:
Avoid contact with skin. Use only with adequate ventilation. Keep out of reach of children. Protect from freezing. Do not
take internally. Close container after each use.
First Aid: If swallowed, do not induce vomiting. Call a physician immediately.
Dual Dispersion Semi-Solid
No. 345 Series
4/10/2017
STORM SYSTEM™
California Paints ▪ 150 Dascomb Rd. ▪ Andover, MA ▪ 01810 ▪ www.stormsystem.com ▪ 800-225-1141
5/17/2013
Exterior
Type:
Acrylic/Alkyd Dispersion
Specular Gloss:
2
Volume Solids:
29.0
@ 60°
%
Solids by Weight:
39.6
%
Dry Film Thickness:
1.0
mils
Vehicle:
81.0
%
Pigment:
19.0
%
Viscosity @ 77 °F:
73
KU
Maximum VOC:
100
g/liter
Flash Pt °F:
Non-combustible
Thinner:
Water
Product Specifications:
Exposure:
Exterior
(Weight Per Gallon:
9.80
Available Package Sizes:
Gallon 5 Gallon
To Handle:
6
To Recoat:
16
hrs.
hrs.
hrs.
To Touch:
4
Drying Times:
lbs. ± .5 lb)
Surface Spread Rate:
s.f./gal.
(Spray Application is 50% of above)
Tools and Equipment:
±
1
Smooth:
200-400
Porous:
150-350
s.f./gal.
Brush -
Natural Bristle
Roller -
Medium Nap
Airless Spray -
.011 to .013
±2
±2
±2
±2
±5
(@ 70-77 °F, 50% R.H.)
Soap & Water
Clean Up:
Available Colors and Bases:
See back page
for complete list