MSDS

Per OSHA-recommended ANSI Z400.1-2004 standard format & in accordance with
European standard format
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
Product Name: Storm System Step 3 Control White Mold Resistant Paint
Product Description: Mold Resistant Coating
Product Code: 69005
Manufacturer: California Products Corporation.
Address:
150 Dascomb Road
Andover MA, 01810
Contact Info:
Tel: [phone]
Emergency Phone: 24 Hour Contact: CHEM-TEL: [phone] (Contract Number: MIS0001450)
INTERNATIONAL 24 HOUR EMERGENCY Phone: [phone]
SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS
Non-hazardous:
Pigmented Latex emulsion coating comprised of water, pigments, llers, additives,
and latex emulsion resin.
Hazardous:
Chemical Name CAS# Percent Exposure Limits
1 - Titanium dioxide 13463-67-7 < 20.0 ACGIH TLV
10 mg/m
3
as Dust
OSHA PEL
10 mg/m
3
as Total Dust
5 mg/m
3
Respirable Fraction
Note: Normal application procedures pose no hazard since titanium dioxide is
wetted and encapsulated, but grinding or sanding dried lms of this product may
yield respirable titanium dioxide dust. Control exposures to less than 0.1 mg/m3
using NIOSH-approved dust lter respirators.
Note: Per 29CFR 1910.1200 (g) (2) (1) (C) (2), only hazardous substances
present in excess of 1.0% by weight (or 0.1% for carcinogens) must be listed on
an MSDS.
SECTION 3: HAZARDS IDENTIFICATION
Emergency Overview:
Product Description: This product is a pigmented liquid.
Health Hazards:
Eyes: May cause slight irritation.
Skin: Substance may cause slight skin irritation.
Inhalation: May cause irritation of respiratory tract.
Ingestion: Ingestion may cause gastrointestinal irritation, nausea, and vomitting.
Flammability Hazards: This product is not ammable. If this product is involved
in a re, the decomposition products generated will include irritating vapors and
gases and some carbon monoxide.
Reactivity Hazards: This product is not reactive.
Environmental Hazards: Although release of this product to the environment is
not expected to cause signicant adverse effect, all releases should be avoided.
SECTION 4: FIRST AID MEASURES
Eyes: Immediately ush eyes with plenty of water for at least 15 minutes and
consult physician.
Skin: Wash skin thoroughly with soap and water. If drenched with product,
remove and wash clothing before reuse.
Ingestion: Ingestion If victim is conscious give 2 glasses of water. Call a
physician.
Inhalation: N/A
MATERIAL SAFETY DATA SHEET
STORM SYSTEM STEP 3 CONTROL
WHITE MOLD RESISTANT PAINT (CA)
SECTION 5: FIRE-FIGHTING MEASURES
Product is non-combustible.
Flash point: Autoignition Temperature:
F: Not ammable
C: Not ammable
F: Not Established
C: Not Established
Extinguishing Media:
Use extinguishing media appropriate for surrounding re
Water Spray OK
Carbon Dioxide OK
Foam OK
Dry Chemical OK
Halon OK
Other Any “ABC” Class
SECTION 6: ACCIDENTAL RELEASE MEASURES
Accidental Release Measures:
Personal Precautions: Do not get in eyes. Do not take internally. Avoid skin
contact. Prevent prolonged or repeated breathing of vapor or spray mists. Keep
unnecessary people away. Floor may be slippery, use care to avoid falling.
Ventilate the area. Remove with inert absorbent.
Environmental Precautions: Keep spills and cleaning run-offs out of municipal
sewers and open bodies of water. Comply with local, state and national
regulations.
SECTION 7: HANDLING AND STORAGE
Handling and Storage:
Storage: Store in a cool, dry place
Keep closure tight and containers upright to prevent leakage.
Precautionary labeling: “KEEP FROM FREEZING”.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
Precautions:
Use only with adequate ventilation.
Avoid contact with skin and eyes. Avoid breathing vapor and spray mist.
Wash hands after using.
This coating may contain materials classied as nuisance particulates (listed “as
Dust” in Section 2) which may be present at hazardous levels only during the
sanding or abrading of the dried lm. If no specic dusts are listed in Section 2, the
applicable limits for nuisance dusts are ACGIH TLV 10 mg/m3 (total dust), 3 mg/
m3 (respirable fraction), OSHA PEL 10 mg/m3 (total dust), 5 mg/m3 (respirable
fraction).
Work Hygienic Practices: Avoid contact with skin. Do not get in eyes. Do not take
internally. Avoid breathing vapors or spray mists.
Ventilation: Use in well-ventilated areas. General exhaust acceptable if the
exposure to materials in Section 2 is maintained below applicable exposure limits.
Refer to OSHA Standards 1910.94, 1910.107, 1910.108.
Respiratory Protection: If personal exposure cannot be controlled below
applicable limits by ventilation, wear a properly tted organic vapor/particulate
respirator approved by NIOSH/MSHA for protection against materials in Section 2.
When sanding or abrading the dried lm, wear a dust/mist respirator approved
by NIOSH/MSHA for dust which may be generated from this product, underlying
paint, or the abrasive.
Eye Protection: Use approved safety eyewear including side shields, chemical
goggles or face shields.
Skin Protection: Wear neoprene or rubber gloves to prevent skin contact if
prolonged skin contact is likely. Wash hands before eating, smoking or using the
wash room.
MSDS DATE: 10/14
Page 1: MSDS for Storm System Step 3 Control White Mold Resistant Paint (CA) - #69005